2006 SUZUKI SX4 E01-31

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-131
DTC P0481: Cooling Fan 2 (A/C Condenser Fan) Control CircuitS6RW0D1104049
Wiring Diagram
Circuit Description
A/C condenser cooling fan motor is turned ON and OFF by its relay which ECM controls. A/C condenser cooling fan
motor is turned ON when ECM outputs A/C ON signal or when engine coolant temp. is 110 °C, 230 °F or more.
DTC Detecting Condition and Trouble Area7Radiator cooling fan control check
1) Run engine until ECT is over 100 °C, 212 °F.
2) Measure voltage between vehicle body ground and
“E01-46” terminal of ECM connector.
Is voltage lower than 1.5 V?Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”. If OK, substitute a
known-good ECM and
recheck.Faulty ECM.
Substitute a known-
good ECM and recheck. Step Action Yes No
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
BLK/WHT
WHT
1
GRN
27
E01-29
10
89
REDBLK
3
5BLK/WHT
RED/BLKE01-58
WHT
4E01-47 GRY
BLU/YEL
6
C01-58
C01-15 C01-30
BLK/ORN
BLKBLKE01-31BLK
I6RW0D110042-01
1. Individual circuit fuse box No.1 5. A/C condenser cooling fan motor 9. “A/C” fuse
2. Ignition switch 6. A/C compressor 10. “IG COIL” fuse
3. A/C condenser cooling fan relay 7. ECM
4. A/C compressor relay 8. “FI” fuse
DTC detecting condition Trouble area
Monitor signal of A/C condenser cooling fan relay is different
from command signal.
(1 driving cycle detection logic but MIL does not light up)• A/C condenser cooling fan relay circuit malfunction
• A/C condenser cooling fan relay malfunction
• ECM malfunction

Downloaded from www.Manualslib.com manuals search engine 1A-136 Engine General Information and Diagnosis:
DTC P0532: A/C Refrigerant Pressure Sensor Circuit LowS6RW0D1104051
Wiring Diagram
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Connect scan tool to DLC with ignition switch turned OFF.
2) Turn ON ignition switch and clear DTC using scan tool.
3) Start engine and warm up engine to normal operating temperature.
4) Run engine at idle and turn both A/C switch and heater blower switch ON (turn ON air conditioning) for 3 min. or
more.
5) Check DTC and pending DTC.
Troubleshooting
NOTE
Before this troubleshooting is performed, read the precautions for DTC troubleshooting referring to
“Precautions for DTC Troubleshooting”.

E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
4
C01-58
C01-15 C01-30
BLK/ORN
BLKBLK
12
3
GRY/REDGRY/RED
ORNORN
5V
5VC01-14
E01-55
E01-54
RED/BLU
E01-31 BLK
I6RW0D110044-01
1. A/C refrigerant pressure sensor 2. To MAP sensor 3. To other sensors 4. ECM
DTC detecting condition Trouble area
A/C refrigerant pressure sensor signal voltage is less than specified
value.
(1 driving detection logic but MIL does not light up)• A/C refrigerant pressure sensor circuit
• A/C refrigerant pressure sensor
• MAP sensor
•ECM
Step Action Yes No
1Was “Engine and Emission Control System Check”
performed?Go to Step 2. Go to “Engine and
Emission Control
System Check”.

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-139
DTC P0601 / P0602 / P0607: Internal Control Module Memory Check Sum Error / Control Module
Programming Error / Control Module Performance
S6RW0D1104053
System Description
Internal control module is installed in ECM.
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Connect scan tool to DLC with ignition switch turned OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool.
3) Start engine and run it at idle if possible.
4) Check DTC and pending DTC by using scan tool.5A/C refrigerant pressure sensor signal circuit check
1) Disconnect connectors from ECM with ignition switch
turned OFF.
2) Measure resistance between “RED/BLU” wire terminal of
A/C refrigerant pressure sensor connector and “E01-55”
terminal of ECM connector.
Is resistance below 2
Ω?“RED/BLU” wire is
shorted to power supply
circuit.“RED/BLU” wire is open
or high resistance
circuit.
6A/C refrigerant pressure sensor ground circuit check
1) Turn OFF ignition switch, measure resistance between
engine ground and “ORN” wire terminal of A/C
refrigerant pressure sensor connector.
Is resistance below 5
Ω?Go to Step 8. Go to Step 7.
7ECM ground circuit check
1) Remove ECM from its bracket with ECM connectors
connected.
2) Measure resistance between engine ground and “E01-
54” terminal of ECM connector.
Is resistance below 5
Ω?“ORN” wire is open or
high resistance circuit.ECM grounds “C01-58”,
“C01-15”, “C01-30” and/
or “E01-31” is open or
high resistance circuit.
8A/C refrigerant pressure sensor check
1) Check A/C refrigerant pressure sensor referring to “A/C
Refrigerant Pressure Sensor and Its Circuit Inspection in
Section 7B” or “A/C Refrigerant Pressure Sensor and Its
Circuit Inspection in Section 7B”.
Is it good condition?Substitute a known-
good ECM and recheck.Faulty A/C refrigerant
pressure sensor. Step Action Yes No
DTC detecting condition Trouble area
DTC P0601:
Data write error or check sum error
(1 driving cycle detection logic)
DTC P0602:
Data programming error
(1 driving cycle detection logic but MIL does not light up)
DTC P0607:
Data programming error
(1 driving cycle detection logic)ECM

Downloaded from www.Manualslib.com manuals search engine 1A-140 Engine General Information and Diagnosis:
DTC Troubleshooting
NOTE
Before this troubleshooting is performed, read the precautions for DTC troubleshooting referring to
“Precautions for DTC Troubleshooting”.

DTC P0616: Starter Relay Circuit LowS6RW0D1104054
Wiring DiagramStep Action Yes No
1DTC recheck
1) Clear DTC referring to “DTC Clearance”.
2) Turn OFF ignition switch.
3) Turn ON ignition switch and check DTC.
Is DTC P0601 or P0607 still indicated?Go to Step 2. Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
2ECM reprogramming check
Was reprogramming of ECM executed?Execute reprogramming
of ECM correctly once
again.Go to step 3.
3ECM power and ground circuit check
1) Check that ECM power supply circuit and ECM ground
circuit is in good condition referring to “ECM Power and
Ground Circuit Check”.
Are check results OK?Substitute a known-
good ECM and recheck.Repair ECM power or
ground circuit.
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
3
461E01-29
C01-58
C01-15 C01-30
BLK/ORN
BLKBLK
5
RED/WHTGRN/WHT
GRN
RED
E01-30
C01-48
BLK/WHT
YEL/GRN
YEL/GRN
WHT
2 7
8 9WHT
WHT/BLU
BLKE01-31
I6RW0D110045-01
1. ECM 4. Main fuse box 7. “ST SIG” fuse
2. Starter motor 5. Starting motor control relay 8. “ST MOT” fuse
3. Ignition switch 6. “IG COIL” fuse 9. “IGN” fuse

Downloaded from www.Manualslib.com manuals search engine 1A-144 Engine General Information and Diagnosis:
DTC P2101: Throttle Actuator Control Motor Circuit Range / PerformanceS6RW0D1104057
Wiring Diagram2Battery voltage supply circuit check
1) Turn OFF ignition switch.
2) Remove ECM from its bracket with ECM connectors
connected.
3) With engine running, measure voltage between “E01-2”
terminal of ECM connector and engine ground.
Is voltage 10 – 14 V?Poor “E01-2”
connection or
intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
If wire and connections
are OK, substitute a
known-good ECM and
recheck.“DOME” fuse blown,
“WHT” or “WHT/RED”
wire is circuit open or
short circuit. Step Action Yes No
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
12V
5VBLK/REDBLK/RED
BLK/YEL
12BLK/YEL
BLK/YEL
BRN/WHT
E01-1
E01-60
C01-58
C01-15 C01-30
BLK/ORN
BLKBLKE01-31 BLK
BLK/RED
RED
BRN
BLU
GRN
GRNGRY
WHT
BLK
GRY
BLK/REDE01-16
E01-45
E01-32
C01-45
C01-44
C01-43
C01-54
C01-40
C01-42
C01-41
1-1
1-2
1-33
45
867
109
E01-29 GRNBLK/WHT
WHT
YEL
I6RW0D110047-01
1. Electric throttle body assembly 3. ECM 8. “IGN” fuse
1-1. Throttle actuator 4. Main relay 9. “IG COIL” fuse
1-2. Throttle position sensor (main) 5. Individual circuit fuse box No.1 10. Ignition switch
1-3. Throttle position sensor (sub) 6. “THR MOT” fuse
2. Throttle actuator control relay 7. “FI” fuse

Downloaded from www.Manualslib.com manuals search engine 1A-160 Engine General Information and Diagnosis:
DTC P2135: Throttle Position Sensor (Main / Sub) Voltage CorrelationS6RW0D1104066
Wiring Diagram9Ground circuit check
1) Remove ECM from its bracket with ECM connectors
connected.
2) Check for proper connection of ECM connector at “E01-
51” terminal.
3) If OK, measure resistance between “E01-51” terminal of
ECM connector and engine ground.
Is resistance below 5
Ω?“WHT” wire is open or
high resistance circuit.Faulty ECM ground
circuit. If circuit is OK,
substitute a known-
good ECM and recheck.
10APP sensor assembly check
1) Check APP sensor (sub) referring to “Accelerator Pedal
Position (APP) Sensor Assembly Inspection in Section
1C”.
Is output voltage within specified value?Substitute a known-
good ECM and recheck.Replace APP sensor
assembly. Step Action Yes No
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
12V
5VBLK/REDBLK/RED
BLK/YEL
12BLK/YEL
BLK/YEL
BRN/WHT
E01-1
E01-60
C01-58
C01-15 C01-30
BLK/ORN
BLKBLKE01-31 BLK
BLK/RED
RED
BRN
BLU
GRN
GRNGRY
WHT
BLK
GRY
BLK/REDE01-16
E01-45
E01-32
C01-45
C01-44
C01-43
C01-54
C01-40
C01-42
C01-41
1-1
1-2
1-33
45
867
109
E01-29 GRNBLK/WHT
WHT
YEL
I6RW0D110049-02
1. Electric throttle body assembly 3. ECM 8. “IGN” fuse
1-1. Throttle actuator 4. Main relay 9. “IG COIL” fuse
1-2. Throttle position sensor (main) 5. Individual circuit fuse box No.1 10. Ignition switch
1-3. Throttle position sensor (sub) 6. “THR MOT” fuse
2. Throttle actuator control relay 7. “FI” fuse

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-179
E01-26RED/
BLUEPS signal10 – 14 V Ignition switch turned ON.
—
0 – 1 VWith engine running at idle
speed, and steering wheel
turned to the right or left as
far as it stops.
E01-27 — — — — —
E01-28YEL/
BLKSerial
communication line
for immobilizer coil
antenna10 – 14 V Ignition switch turned ON. —
E01-29BLK/
WHTIgnition switch
signal0 – 1 V Ignition switch turned OFF.
—
10 – 14 V Ignition switch turned ON.
E01-30 WHTStarting motor
control relay output0 – 1 V Ignition switch turned ON.
—
0 – 1 VIgnition switch is turned to
ST (engine cranking)
position.
E01-31 BLK Ground for ECM Below 0.3 V Ignition switch turned ON. —
E01-32 GRNPower supply of
throttle actuator
drive circuit10 – 14 V Ignition switch turned ON. —
E01-33 — — — — —
E01-34 REDOutput for 5 V
power source of
APP sensor (sub)4.5 – 5.5 V Ignition switch turned ON. —
E01-35 BRNOutput for 5 V
power source of
APP sensor (main)4.5 – 5.5 V Ignition switch turned ON. —
E01-36 YELAPP sensor (sub)
signal0.37 – 0.38 VIgnition switch turned ON
and accelerator pedal at
idle position after warmed
up engine.
—
1.70 – 2.00 V
(“Reference
waveform No.30: ”)Ignition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine.
E01-37 GRNAPP sensor (main)
signal0.75 – 0.85 VIgnition switch turned ON
and accelerator pedal at
idle position after warmed
up engine.
—
3.46 – 4.24 V
(“Reference
waveform No.30: ”)Ignition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine.
E01-38 — — — — —
E01-39 — — — — —
E01-40 — — — — —
E01-41 — — — — —
E01-42 — — — — —
E01-43 — — — — —
E01-44 — — — — —
E01-45 BRNThrottle actuator
control relay output0 – 1 V Ignition switch turned ON. — Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-193
ECM Power and Ground Circuit CheckS6RW0D1104073
Wiring Diagram
Circuit Description
When the ignition switch is turned ON, the main relay turns ON (the contact point closes) and the main power is
supplied to ECM.
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
BLK/WHT
BLK/RED
BLK/RED
BLK/RED
BLK/YELBLK/YEL
BLK/YEL
GRN
BRN/WHT
12V5V
2
13
12
13
14-1
15-1
15-2 14-2 4
56
E01-29
E01-1
E01-60
E01-16
9 87
1011
WHTWHT/REDE01-2
C01-58
C01-15 C01-30
BLK/ORN
BLKBLKBLK
WHT
GRY/RED
RED/BLK
GRY/BLU
C01-14
C01-53
C01-55
E01-54ORN
RED/BLUE01-55
BRNGRNBLU
REDYELWHT
E01-35E01-37E01-52
E01-51
E01-34E01-36
E01-50
REDGRN
WHTBLK
BLU
YEL
C01-43C01-54
C01-40C01-42
C01-45
C01-44
C01-41
E01-31
GRY
BLK
I6RW0D110052-01
1. Main fuse box 7. Individual circuit fuse box No.1 13. A/C refrigerant pressure sensor (if equipped with A/C)
2. Ignition switch 8. “IGN” fuse 14-1. APP sensor (main)
3. Main relay 9. “FI” fuse 14-2. APP sensor (sub)
4. BCM (included in junction block assembly) 10. “DOME” fuse 15-1. TP sensor (main)
5. “IG COIL” fuse 11. DLC 15-2. TP sensor (sub)
6. ECM 12. MAP sensor (if equipped)