2006 SUBARU FORESTER manual radio set

Instruments and controls
3-17
„Cruise control set indica-
tor lightThe cruise control set indicator light
comes on when the ignition switch is
turned to the “ON” position and goes out
after approximately three seconds.
This light comes on when vehicle speed
has been set.
ClockTo adjust the clock, open the small article
storage compartment in the dashboard
with the vehicle parked in a safe place. To set the hour, press the “H” button. To
set the minutes, press the “M” button. To
reset the minutes to “00” with a radio time
signal, push the “Reset” button.
NOTEThe clock uses a liquid-crystal display.
You will find time indications hard to
see if you wear polarized glasses.
300578
HM
RESET300579
To ensure safety, do not attempt to
set the time while driving, as an ac-
cident from inadequate attention to
the road could result.
ProCarManuals.com

5
Audio
Antenna system .................................................. 5-2
FM reception ........................................................... 5-2
Installation of accessories ................................ 5-2
Audio set ............................................................. 5-3
Type A audio set ..................................................... 5-3
Type B audio set ..................................................... 5-3
In-dash 6 CD auto changer (Optional audio unit – if equipped) ........................................................ 5-3
Type A audio set (if equipped) .......................... 5-4
Radio operation ...................................................... 5-4
Compact disc player operation ............................. 5-8
CD changer control (if optional in-dash CD changer is connected) ......................................... 5-10
Type B audio set (if equipped) .......................... 5-12
Radio operation ...................................................... 5-12
Built-in CD changer operation ............................... 5-16
In-dash 6 CD auto changer (if equipped) ......... 5-19
Loading and unloading compact discs ................ 5-19
Precautions to observe when handling a compact disc ................................................... 5-21
ProCarManuals.com

Audio
5-3
Audio setYour SUBARU may be equipped with one
of the following audio sets. See the pages
indicated in this section for operating de-
tails.„Type A audio setyRadio operation: refer to page 5-4
y Compact disc player operation: refer to
page 5-8
y CD changer control: refer to page 5-10
„ Type B audio setyRadio operation: refer to page 5-12
y Built-in CD changer operation: refer to
page 5-16
„ In-dash 6 CD auto changer
(Optional audio unit – if
equipped)yInserting and removing a disc or all
discs: refer to page 5-19
500214
500215
500216
ProCarManuals.com

5-4
Audio
Type A audio set (if equipped)The radio will operate only when the ignition switch is in the “ACC” or “ON” position.„Radio operation
(1) (2)
(3)
(4)
(5)
(6)
500217
(1) Power switch, Volume control, Tone/
Fader/Balance control dial
(2) BAND button
(3) Tuning buttons
(4) Preset buttons
(5) AUDIO button
(6) SCAN button
T Power switch and volume/bass/tre-
ble/fader/balance control (PWR/
VOL)
The dial (1) is used for both power (ON/
OFF) and volume control. The radio is
turned ON and OFF by pushing the dial
and the volume is controlled by turning the
dial.
V Tone and balance control
The “VOLUME” control knob normally
function as volume control. This knob be-
come a control for Treble, Bass, Fader or
Balance when you select the appropriate
audio mode.
Choose desired volume level for each
mode by turning the “VOLUME” control
knob. The control function returns to vol-
ume control mode after approximately 5
seconds.
To change control modes: Each brief
press of the “AUDIO” button changes con-
trol modes in the following sequence start-
ing from volume control mode. (When the
ProCarManuals.com

5-6
Audio
TFM/AM/Weather band selection but-
ton (BAND)
Push the “BAND” button when the radio is
on to select FM1, FM2, AM or Weather
band (WB) reception. Each time this but-
ton is pressed, the band will change in the
following order:
The display indicates which one is cur-
rently selected.
T Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received.
T Tuning (TUNE)
V Manual tuning (TUNE)
Push the “ ” side of the tuning button
(3) to increase the tuning frequency and
press the “ ” side of the button to de-
crease it.
Each time the button is pressed, the fre-
quency changes 10 KHz in the AM wave-
band and 0.2 MHz in the FM waveband.
V Manual tuning for weather band
When weather band mode is selected,
press the “ ” side of the tuning button (3) to change the WB channel up and
press the “ ” side of the tuning button
to change the WB channel down. Each
time the button is pressed, the WB chan-
nel changes to the next channel.
T
Seek tuning
If the tuning button (3) is pressed for long-
er than half of a second, the radio will be-
gin to automatically search for receivable
frequencies and will stop at the first one
found. This function may not be available,
however, when radio signals are weak. In
such a situation, perform manual tuning to
select the desired station.
T Automatic tuning (SCAN)
Press the “SCAN” button (6) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper- ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
T
Selecting preset stations
Presetting a station with a preset button
(4) allows you to select that station in a
single operation. Up to six WB, AM, FM1
and FM2 stations each may be preset.
T How to preset stations
1. Press the “BAND” selection button to
select AM, FM1, FM2 or WB reception.
2. Press the “SCAN” button (6) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (4) for
at least 2 seconds to store the frequency.
At this time, there will momentarily be no
sound from the radio. If the button is
pressed for less than 2 seconds, the pre-
ceding selection will remain in memory.
NOTEy If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.
y If a cell phone is placed near the ra-
dio, it may cause the radio to emit
FM1 FM2 AM
WB
ProCarManuals.com

5-12
Audio
Type B audio set (if equipped)The radio will operate only when the ignition switch is in the “ACC” or “ON” position.„Radio operation
(1) (2) (3) (4) (5) (6)
(7)
(8)
500220
(1) SCAN button
(2) FM/AM selection button
(3) WB (weather band) button
(4) Power switch, Volume control, Bass/
Midrange/Treble control and Fader/
Balance control dial
(5) TONE button
(6) Fader/Balance selection button
(7) Preset buttons
(8) Tuning buttons
T Power switch and volume/bass/tre-
ble/fader/balance control (PWR/
VOL)
The dial (4) is used for both power (ON/
OFF) and volume control. The radio is
turned ON and OFF by pushing the dial
and the volume is controlled by turning the
dial.
This dial is used for bass/midrange/treble
controls when the “TONE” button (5) is in
the depressed position. It is also used for
fader/balance controls when the “BAL”
button (6) is in the depressed position.
ProCarManuals.com

5-14
Audio
starting from bass control mode. (When
the radio is first turned on, the control
mode is in the volume control.)
VFader and balance control
The volume control dial (4) normally func-
tion as volume control. The dial become
the controls for Fader or Balance when
you select the appropriate fader and bal-
ance control mode.
Choose desired setting for each mode by
turning the volume control dial. The con-
trol function returns to volume control
mode after approximately 5 seconds.
To change control modes: Each brief
press of the “BAL” button (6) changes
control modes in the following sequence
starting from fader control mode. (When
the radio is turned on, the control mode is
in the volume control.) V
Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims
when the light switch is in the “ ” or
“ ” positions. If this makes the display
difficult to read, press the volume dial for
more than 1.5 seconds to return the dis-
play to original brightness.
Subsequently pressing the volume dial
again for more than 1.5 seconds or if you
can safely do so, turning the light switch to
the OFF position and back to the “ ”
or“ ” position makes the radio display
dim again.
T FM/AM selection button (FM/AM)
Push the “FM/AM” button when the radio
is on to select FM1, FM2 or AM reception.
Each time this button is pressed, the band
will change in the following order:
The display indicates which one is cur-
rently selected.
T Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received. T
Weather band button (WB)
Press the “WB” button when the radio is
on to select the weather band.
T Manual tuning (TUNE)
V Manual tuning for AM and FM wave-
band
Push the “ ” side of the tuning button
(8) to increase the tuning frequency and
press the “ ” side of the button to de-
crease it.
Each time the button is pressed, the fre-
quency changes 10 KHz in the AM wave-
band and 0.2 MHz in the FM waveband.
V Manual tuning for weather band
When weather band mode is selected,
press the “ ” side of the tuning button
(8) to change the WB channel up and
press the “ ” side of the button to
change the WB channel down. Each time
the button is pressed, the WB channel
changes to the next channel.
T Seek tuning
If the tuning button (8) is pressed for long-
er than half of a second, the radio will be-
gin to automatically search for receivable
frequencies and will stop at the first one
found. This function may not be available,
however, when radio signals are weak. In
such a situation, perform manual tuning to
VOLUME
BASS
TREBLE
MIDDLE
FADER BALANCE VOLUME
FM1 FM2 AM
ProCarManuals.com

Audio
5-15
– CONTINUED –
select the desired station.
TAutomatic tuning (SCAN)
Press the “SCAN” button (1) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
T Selecting preset stations
Presetting a station with a preset button
(7) allows you to select that station in a
single operation. Up to six AM, FM1, FM2
and WB stations each may be preset.
T How to preset stations
1. Press the “FM/AM” selection button to
select AM, FM1 or FM2 reception.
OR
Press the “WB” button (3) to select the
weather band.
2. Press the “SCAN” button (1) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (7) for
at least 1.5 seconds to store the frequen-
cy. The frequency of the station will flash
once on the display at this time.
NOTEy If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.
y If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise
does not indicate a radio fault.
ProCarManuals.com