2006 SUBARU FORESTER ignition

2-12
Keys and doors
with the leftmost digit.NOTEIf you do not start entering the number
using the lock switch before the elec-
tronic tone stops sounding, an error
will occur. In this event, perform the
procedure again beginning with part 3.
9. When you have finished entering the
code a second time, an electronic tone will
sound for one second to indicate comple-
tion of registration, provided the code en-
tered the second time is identical to that
entered the first time.NOTEIf the code entered the second time is
not identical to the code entered the
first time, an error will occur. In this
event, perform the procedure again be-
ginning with part 5. If an error occurs
five times, perform the procedure
again starting with part 3.
10.If you wish to program another trans-
mitter code into the system (up to four
transmitter codes can be programmed
into the system), perform the procedure
beginning with part 4. When you have fin-
ished programming all of the necessary
transmitter codes into the system, remove
the key from the ignition switch.
11.Test every registered transmitter toconfirm correct operation.
T
Deleting old transmitter codes
The control unit of the keyless entry sys-
tem has four memory locations to store
transmitter codes, giving it the ability to
operate with up to four transmitters. When
you lose a transmitter, the lost transmit-
ter’s code remains in the memory. For se-
curity reasons, lost transmitter codes
should be deleted from the memory.
To delete old transmitter codes, program
four transmitter codes into the system. If
you have only one current transmitter,
program it four times. If you have two cur-
rent transmitters, program each one twice.
If you have three current transmitters, pro-
gram two of them once and the third one
twice. This process will leave only current
transmitter codes in the system’s memory.
NOTEMake sure no one else is operating
their keyless entry system within range
of your vehicle when programming
transmitters. If someone else were to
operate their remote transmitter while
you are programming your transmit-
ters, it is possible that their transmitter
code will be programmed into your
system, allowing them unauthorized
access to your vehicle.
Alarm systemThe alarm system helps to protect your
vehicle and valuables from theft. The horn
sounds and the turn signal lights flash if
someone attempts to break into your vehi-
cle. The starter motor is also interrupted to
prevent starting the vehicle without a key.
The system can be armed and disarmed
with the remote transmitter.
The system does not operate when the
key is inserted into the ignition switch.
Your vehicle’s alarm system has been set
for activation at the time of shipment from
the factory. You can set the system for de-
activation yourself or have it done by your
SUBARU dealer.„ System operationThe alarm system will give the following
alarm when triggered:
yThe vehicle’s horn will sound and the
turn signal lights will flash for 30 seconds.
y If any door or the rear gate remains
open after the 30-second period, the horn
will continue to sound for a maximum of 3
minutes. If the door and the rear gate are
closed while the horn is sounding, the
horn will stop sounding with a delay of up
to 30 seconds.
ProCarManuals.com

Keys and doors
2-13
– CONTINUED –
The alarm is triggered by:
yOpening a door or the rear gate.
y Physical impact to the vehicle, such as
forced entry (only vehicles with shock sen-
sors (dealer option))„ Activating and deactivating
the alarm systemTo change the setting of your vehicle’s
alarm system for activation or deactiva-
tion, do the following.
1. Disarm the alarm system (see “Disarm-
ing the system” in this section).
2. Sit in the driver’s seat and shut all
doors and the rear gate.
3. Turn the ignition switch to the “ON” po-
sition.
4. Hold down the UNLOCK side of the
driver’s power door locking switch, open
the driver’s door within the following 1 sec-
ond, and wait 10 seconds without releas-
ing the switch. The setting will then be
changed as follows:
If the system was previously activated:
The horn sounds twice, indicating that the
system is now deactivated.
If the system was previously deactivated:
The horn sounds once, indicating that the
system is now activated.
NOTEYou may have the above setting
change done by your SUBARU dealer.„If you have accidentally trig-
gered the alarm systemT To stop the alarm
Do any of the following operations:
y Press any button on the remote trans-
mitter.
y Cycle the ignition switch from the
“LOCK” to “ON” position three times within
5 seconds.„ Arming the systemT To arm the system using remote
transmitter
1. Close all windows and the moonroof (if
so equipped).
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the vehi-
cle.
4. Make sure that the engine hood is
locked.
5. Close all doors and the rear gate.
: Press to Arm the system.
: Press to Disarm the system.
Security indicator light
6. Briefly press the “ ” button (for less
200808200815
ProCarManuals.com

2-14
Keys and doors
than two seconds). All doors and the rear
gate will lock, an electric chirp will sound
once, the turn signal lights will flash once,
and the indicator lights will start flashing
rapidly. After rapid flashing for 30 seconds
(standby time), the indicator lights will
then flash slowly (twice approximately ev-
ery two seconds), indicating that the sys-
tem has been armed for surveillance.
If any of the doors or the rear gate is not
fully closed, an electronic chirp sounds
five times, the turn signal lights flash five
times to alert you that the doors or the rear
gate are not properly closed. When you
close the door, the system will automati-
cally arm and doors will automatically
lock.
TTo arm the system using power
door locking switches
1. Close all windows.
2. Remove the key from the ignition
switch.
3. Open the doors and get out of the vehi-
cle.
4. Make sure that the engine hood is
locked.
5. Close the doors and the rear gate but
leave only the driver’s door or the front
passenger’s door open. 6. Push the front side (“LOCK” side) of
the power door locking switch to set the
door locks.
7. Close the door. An electronic chirp will
sound once, the turn signal lights will flash
once, and the indicator lights will start
flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator
lights will then flash slowly (twice approxi-
mately every two seconds), indicating that
the system has been armed for surveil-
lance.
NOTEy
The system can be armed even if the
engine hood, the windows and/or
moonroofs are opened. Always make
sure that they are fully closed before
arming the system. y
The 30-second standby time can be
eliminated if you prefer. Have it per-
formed by your SUBARU dealer.
y The system is in the standby mode
for a 30-second period after locking the
doors with the remote transmitter. The
security indicator light will flash at
short intervals during this period.
y If any of the following actions is done
during the standby period, the system
will not switch to the surveillance state. y Doors are unlocked using the re-
mote transmitter.
y Any door or the rear gate is
opened.
y Ignition switch is turned to the
“ON” position.
y The engine does not start even when
the ignition switch is turned to the
“START” position once the alarm sys-
tem has been triggered.
„ Disarming the systemBriefly press the “ ” button (for less
than two seconds) on the remote transmit-
ter. The driver’s door will unlock, an elec-
tronic chirp will sound twice, the turn sig-
nal lights will flash twice and the indicator
light will go off.
200883
ProCarManuals.com

Keys and doors
2-15
– CONTINUED –
NOTE (Models with immobiliz-
er)If your vehicle is equipped with an im-
mobilizer, the immobilizer’s function
will cause the security indicator light to
flash (approximately once every three
seconds) even after the system is dis-
armed.NOTEThe system can be disarmed by the fol-
lowing method, too.
yCycle the ignition switch from the
“LOCK” to the “ON” position three
times within 5 seconds.
T Emergency disarming
If you cannot disarm the system using the
transmitter (i.e. the transmitter is lost, bro-
ken or the transmitter battery is too weak),
you can disarm the system without using
the transmitter.
1. Unlock the door with the key and then
open the door.
2. Insert the key into the ignition switch
and cycle it from the “LOCK” to the “ON”
position three times within 5 seconds.„Valet modeWhen you choose the valet mode, the se-
curity system does not operate. In valet
mode, the remote transmitter is used only for locking and unlocking the doors and
rear gate and panic activation.
To enter the valet mode, change the set-
ting of your vehicle’s alarm system for de-
activation mode. (Refer to “Activating and
deactivating the alarm system” in this sec-
tion.) The security indicator light will con-
tinue to flash once every three seconds in-
dicating that the system is in the valet
mode (only vehicle with an immobilizer).
To exit valet mode, change the setting of
your vehicle’s alarm system for activation
mode. (Refer to “Activating and deactivat-
ing the alarm system” in this section.)
NOTEIf your vehicle is not equipped with an
immobilizer, the security indicator light
does not flash during the valet mode.„
Passive armingWhen passive arming mode has been
programmed by the dealer, arming of the
system is automatically accomplished
without using the remote transmitter. Note
that in this mode, DOORS MUST BE
MANUALLY LOCKED.
T To enter the passive mode
If you wish to program the passive arming
mode, have it done by your SUBARU dealer.
T
Arming the system
1. Turn the ignition switch to the “ON” po-
sition.
1) ON
2) LOCK2. Turn the ignition switch from “ON” to
“LOCK” position and remove the key from
the ignition switch.
1
2
200816
ProCarManuals.com

2-16
Keys and doors
3. Open the doors and get out of the vehi-
cle.
4. Before closing the doors, lock all doors
with the inside door lock levers.
5. Close the doors. The system will auto-
matically arm after one minute.
In the passive mode, the system can also
be armed with the remote transmitter or
with the power door locking switches. If
the remote transmitter or power door lock-
ing switch is used to lock the vehicle, arm-
ing will take place immediately regardless
of whether or not the passive mode has
been selected.
TDisarming the system
To disarm the system, briefly press the
“ ” button on the transmitter.„ Tripped sensor identificationThe security indicator light flashes when
the alarm system has been triggered. Al-
so, the number of flashes indicates the lo-
cation of unauthorized intrusion or the se-
verity of impact on the vehicle.
yWhen the ignition switch is turned to the
“ON” position, the indicator light will light
for 1 second and then flash as follows:
When a door or rear gate was opened:
5 times
When the ignition switch was turned to
the “ON” position: 3 times
When a strong impact or multiple im-
pacts were sensed: twice (only vehicles with shock sensors (dealer option))
When a light impact was sensed: once
(only vehicles with shock sensors (deal-
er option))
NOTEAny of the above indicator light flash-
ings will recur each time the ignition
switch is turned to the “ON” position.
Rearming the alarm system cancels
the flashing.„
Shock sensors (dealer op-
tion)The shock sensors trigger the alarm sys-
tem when they sense impacts applied to
the vehicle and when any of their electric
wires is cut. The alarm system causes the
horn to sound and the turn signal lights to
flash for a short time when the sensed im-
pact is weak, but it warns of a strong im-
pact or multiple impacts by sounding the
horn and flashing the turn signal lights,
both lasting approximately 30 seconds.
If you desire, your SUBARU dealer can
connect them and set them for activation
or deactivation.NOTEyThe shock sensors are not always
able to sense impacts caused by
breaking in, and cannot sense an im-
200817
In passive mode, the system will au-
tomatically activate the alarm but
WILL NOT automatically lock the
doors. In order to lock the doors you
must either lock them as indicated
in step 4 above or with the key once
they have been closed. Failure to
lock the doors manually will result
in a higher security risk.
ProCarManuals.com

2-18
Keys and doors
Windows„Power windowsThe power windows operate only when
the ignition switch is in the “ON” position. T
Driver’s side switches
1) Lock switch
2) For driver’s window (with one-touch auto
down feature)
3) For front passenger’s window
4) For rear left window
5) For rear right windowAll door windows can be controlled by the
power window switch cluster at the driver
side door. V
Operating the driver’s window
1) Open
2) Automatically open
3) CloseTo open:
Push the switch down lightly and hold it.
The window will open as long as the
switch is held.
This switch also has a one-touch auto
down feature that allows the window to be
opened fully without holding the switch.
Push the switch down until it clicks and re-
lease it, and the window will fully open. To
stop the window halfway, pull the switch
up lightly.
To close:
Pull the switch up lightly and hold it. The
window will close as long as the switch is
To avoid serious personal injury
caused by entrapment, you must do
the following.yWhen operating the power win-
dows, be extremely careful to pre-
vent anyone’s fingers, arms, neck
or head from being caught in the
window.yAlways lock the passengers’ win-
dows using the lock switch when
children are riding in the vehicle.yBefore leaving the vehicle, always
remove the key from the ignition
switch for safety and never allow
an unattended child to remain in
the vehicle. Failure to follow this
procedure could result in injury to
a child operating the power win-
dow.
1
2
4 5 3200819
3
1
2200820
ProCarManuals.com

2-22
Keys and doors
If the moonroof is opened, the sun shade
also moves back. yNever let anyone’s hands, arms,
head or any objects protrude from
the moonroof. A person could be
seriously injured if the vehicle
stops suddenly or turns sharply
or if the vehicle is involved in an
accident.
To avoid serious personal injury
caused by entrapment, you must
do the following.yBefore closing the moonroof,
make sure that no one’s hands,
arms, head or other objects will be
accidentally caught in the moon-
roof.yBefore leaving the vehicle, always
remove the key from the ignition
switch for safety and never allow
an unattended child to remain in
the vehicle. Failure to follow this
procedure could result in injury to
a child operating the moonroof.
yNever try to check the anti-entrap-
ment function by deliberately
placing part of your body in the
moonroof.
y Do not sit on the edge of the open
moonroof.
y Do not operate the moonroof if
falling snow or extremely cold
conditions have caused it to
freeze shut.
ProCarManuals.com

3
Instruments and controls
Ignition switch .................................................... 3-3
LOCK ....................................................................... 3-3
ACC .......................................................................... 3-4
ON ............................................................................ 3-4
START ...................................................................... 3-4
Key reminder chime ............................................... 3-5
Ignition switch light (if equipped) ......................... 3-5
Key interlock release (AT vehicles only) .............. 3-5
Hazard warning flasher ...................................... 3-6
Meters and gauges ............................................. 3-6
Speedometer ........................................................... 3-6
Odometer/Trip meter .............................................. 3-6
Tachometer ............................................................. 3-7
Fuel gauge ............................................................... 3-7
Temperature gauge ................................................ 3-8
Outside temperature indicator .............................. 3-8
Warning and indicator lights ............................. 3-9
Seatbelt warning light and chime .......................... 3-9
SRS airbag system warning light .......................... 3-10
Front passenger’s frontal airbag ON and OFF indicators .............................................................. 3-10
CHECK ENGINE warning light/Malfunction indicator
lamp ....................................................................... 3-11
Charge warning light .............................................. 3-12
Oil pressure warning light ..................................... 3-12
AT OIL TEMPerature warning light (ATvehicles) .......................................................... 3-12
ABS warning light ................................................... 3-12 Vehicle Dynamics Control warning light
(if equipped)/Vehicle Dynamics Control OFF
indicator light (if equipped) ................................. 3-13
Brake system warning light ................................... 3-14
Door open warning lights ...................................... 3-15
Low fuel warning light ............................................. 3-15
All-Wheel Drive warning light (AT vehicles) ......... 3-15
Vehicle Dynamics Control operation indicator light (if equipped) ................................................. 3-16
Shift position indicator (AT vehicles) ................... 3-16
Turn signal indicator lights .................................... 3-16
High beam indicator light ....................................... 3-16
Cruise control indicator light ................................. 3-16
Cruise control set indicator light .......................... 3-17
Clock .................................................................... 3-17
Light control switch ........................................... 3-18
Headlights ............................................................... 3-18
High/low beam change (dimmer) .......................... 3-18
Headlight flasher ..................................................... 3-19
Daytime running light system ............................... 3-19
Turn signal lever ................................................. 3-20
Illumination brightness control ......................... 3-20
Headlight beam leveler (Canada-spec. 2.5XT) ............................................................... 3-21
Parking light switch ........................................... 3-21
Front fog light button ......................................... 3-21
Wiper and washer ............................................... 3-22
Windshield wiper and washer switches ............... 3-23
ProCarManuals.com