2006 SUBARU BAJA wheel

3-34
Instruments and controls
The indicator light located on the button will come on
when the outside mirror defogger heater in operation.
To turn it off, push the button again.Tilt steering wheelTilt steering wheel
Do not adjust the steering wheel tilt position
while driving. This may cause loss of vehicle
control and result in personal injury.
1. Adjust the seat position. Refer to the “Front seats”
section (chapter 1).
2. Pull the tilt lock lever down.
3. Move the steering wheel to the desired level.
4. Push the lever up to lock the steering wheel in
HS3043BA

3-35
Instruments and controls
– CONTINUED –
place.
5. Make sure that the steering wheel is securely
locked by moving it up and down.HornHorn
To sound the horn, push the horn pad.
HS3044BA

4-2
Climate control
Climate controlVentilator „
Driver’s side ventilators
1) Open
2) Close
Move the thumb-wheel up and down or right and left to
adjust the flow direction. „
Center ventilators
Move the thumb-wheel up and down or right and left to
adjust the flow direction.
12UB4038BB
UB4039BA

4-3
Climate control
– CONTINUED –
„Front passenger’s side ventilators
1) Open
2) Close
Move the thumb-wheel up and down or right and left to
adjust the flow direction.
1
2
UB4040BB

4-7
Climate control
– CONTINUED –
ON position (Recirculation): Interior air is recirculat-
ed inside the vehicle. Push the air inlet selection but-
ton to the ON position. The indicator light will come on.
Push the air inlet selectio n button to the ON position
for fast cooling with the air conditioner or when driving
on a dusty road.
OFF position (Outside Air): Outside air is drawn into
the passenger compartment. Push the air inlet selec-
tion button again to the OFF position. The indicator
light will go off.
Push the air inlet selection button to the OFF position
when the interior has cooled to a comfortable temper-
ature and the road is no longer dusty. „
Heater operation
T Defrosting or defogging the windshield
To direct warm air to the windshield and front door win-
dows:
1. Set the air flow control dial to “ ”.
2. Turn the temperature control dial all the way to the right.
3. Set the fan speed control dial to the highest speed.
NOTE
Warm air also comes out from the right and left air
outlets. To stop warm ai r flow from these outlets,
turn the corresponding thumb-wheel to the
UB5011AA

4-8
Climate control
“”
posit io n.
T Heating and defrosting
To direct warm air toward the floor and the windshield:
1. Set the air flow control dial to “ ”.
2. Set the temperature control dial to the desired tem-
perature level.
3. Set the fan speed control dial to the desired speed.
NOTE
Warm air also comes out from the right and left air
outlets. To stop warm ai r flow from these outlets,
turn the corresponding thumb-wheel to the
“” posit io n. T
Heating
To direct warm air toward the floor:
1. Set the air inlet selection button to the “OFF” posi- tion.
2. Set the air flow control dial to “ ”.
3. Set the temperature control dial to the desired tem- perature level.
4. Set the fan speed control dial to the desired speed.NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding thumb-wheel to the
“ ” position.
UB5012AA
UB5013AA

6-32
Interior and exterior equipments
ly locked.
If this does not lock the cover, release it from a slightly
higher position. Do not push the cover forcibly to lock it. „
Removal and installation of the hard bed cover
1) Brackets
y When removing the bed cover, never remove
the brackets shown in the above drawing. y
Removal and installation work should be per-
formed by at least two adults. y During the removal and installation work, be
careful not to trap yo ur fingers between the
cover and cargo bed.
The bed cover can be removed and reinstalled as de-
sired. T Removal
1. Open the front section of the cover. (Refer to
“Opening and closing the hard bed cover” in this sec-
tion.)
2. Take out the wheel nut wrench from the tool bag.
(Refer to “Jack and tools” section in chapter 9.)
1
UB6075BA

6-33
Interior and exterior equipments
– CONTINUED –
1) Bolts
3. Remove the two bolts shown in the above drawing
using the wheel nut wrench.
1
UB6069BAUB6070BA