0-9
CIRCUITundefined
4891-01
4891-01
ABS/ESP
WHEEL SPEED SENSOR, STOP LAMP SW, DIAGNOSIS,
WARNING LAMP
1)
(1) CONNECTOR INFORMATION
(2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
0-9
CLUSTER
RODIUS 2007.07
8010-10
2) Speedometer
The speedometer indicates the vehicle speed by calculating the signals from the rear right
wheel speed sensor through ABS or ESP unit.
If the speedometer pointer vibrates, stands at a certain range or sounds abnormal noise, there
could be defectives in speedometer. However, these symptoms also could be appeared when
the tire has uneven wear, different tire inflation pressures or different tire specifications.
Perform the speedometer test regarding the tolerance as described. However, it is not simila
r
simple work in field due to lack of measuring conditions such as test equipment and
preciseness.
Check the allowable tolerance of the speedometer and operations of the trip odometer by
using a tester.
Check if the speedometer pointer is shaking and the abnormal noise sounds.
Eliminate the hysteresis by tapping the speedometer. 1.
2.
3.
The allowable tolerance increases when the tires are worn or the tire pressure is out of
specified range. -
0-4
RODIUS 2007.07
3410-01
TRANSFER CASE
1. PART TIME TRANSFER CASE OVERVIEW
By using the planetary gear sets, two-gears shift type part time transfer case achieves direct
connection when selecting 4WD “HIGH” and 2.48 of reduction gear ratio when selecting
4WD “LOW”.
The silent chain in transfer case transfers the output power to front wheels.
Simple operation of switches on instrument panel allows to shift to “2H”, “4H” and “4L”
easily while driving.
The warning lamp alarms the driver when the system is defective.
0-9
TRANSFER CASE
RODIUS 2007.07
3410-01
Ring, snap
Ring, snap
Ring, snap
Bearing
Hub, circular
Asm. -shaft, input
Plate, thrust
Gear, sun
Snap ring
Asm. -carrier (complete)
Hub reduction
Asm. -shaft, main
Clamp hose
Hose
Filter
Asm. -coil, electric
Asm. -cam/coil hsg.
Ring, snap
Armature
Hub, lockup
Spring, sleeve return
Collar, lockup
Sprocket, driving
Spring, return
Rail, shift
Fork, shift
Asm. -fork, shift
Cam, electric shift
Spring, torsion
Spacer
Shaft, shift
Ring, retaining
Asm. -case, transfer
Barb, breather 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.Decal
Shaft, output
Deflector, dust
Magnet
Ring snap
Sprocket lower
Spacer
Chain
Ring retaining
Bearing
Bearing
Cover
Bendable clip
Bolt, Metric
Seal, oil
Washer
Nut, Metric
Flange, companion
Seal, oil
Spacer
Tone wheel (upper)
Nut, Metric
Clip, “J”
Bolt, hex head
Bracket, relay mounting
Locking clip
Connector
Bolt, hex head
Capscrew, hex head
Asm. -motor, electric
Seal, oil
Plug, pipe
Sealing Compound 35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
0-17
TRANSFER CASE
RODIUS 2007.07
3410-01
8. SYSTEM OPERATION
1) Transfer Case Control Unit (Tccu)
(1) 4WD Operation
TCCU is located under the front left seat and
permits the vehicle to shift from two-wheel
drive to four-wheel drive (and back shift)
according to drivers switch operation during
driving (For the shifting between 4WD HIGH
and 4WD LOW, stop the vehicle).
2H → 4H ▶
Change the 4WD switch in instrument panel from 2H to 4H.
This shift is available during driving.
“4WD HIGH” indicator in meter cluster comes on. -
-
-
When the system is defective
“4WD CHECK” warning lamp comes
on -
Change the 4WD switch in instrument panel from 4H to 2H.
This shift is available during driving.
“4WD HIGH” indicator in meter cluster goes out.
“4WD CHECK” warning lamp comes on when the system is defective. -
-
-
- 4H → 2H ▶
