2006 SSANGYONG REXTON ECO mode

undefined
8710-08
RKSTICS
Washer Coupled Wiper in Rain Sensing Mode
The washer coupled wiper is operated when receiving the washer switch input with the
ignition switch "ON" and the AUTO switch "ON" in the rain sensing mode. At this moment,
the communication with the rain sensor is overridden. However, the washer switch input is
overridden during the continuous operation.
The operation data is sent to the rain sensor even during the washer coupled wiper's
operation. 1.
2.
Rain Sensing Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
sensitivity is increased (while the ignition key is in the "ON" position, the AUTO switch is in
the "ON" position, and the wiper motor is in "Parked" position). However, the wiper moto
r
can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper moto
r
runs only one cycle. *

undefined
8710-08
RKSTICS
Speed Sensitive AUTO Wiper
For RKSTICS without the rain sensor, perform the following operation:
1. Controls the wiper intermittent operation by the values from the vehicle speed
and the volume.
Calculates and converts the Intermittent interval automatically by using the
AUTO
VOLUME when the ignition switch is in the "ON" position and the AUTO switch is in the
"ON" position.
The wipers are operated in vehicle speed sensitive mode when turning the AUTO switch to
the "ON" position with the engine running or starting the engine with the AUTO switch
positioned to "ON".
Intermittent interval (at 0 km/h): 3
0.5 ~ 19 2 seconds -
-
-
2. Vehicle speed calculation
[Input the vehicle speed]
It is calculated by the numbers of input pulses for one second.
1 [PULSE/SEC] =
1.41 [km/h] 60 [km/h] x 60 [sec]
637 x 4 PULSE
3. VOLUME calculation
The pause time of the vehicle speed sensitive AUTO wiper is calculated by the
AUTO
volume (input voltage). Each level has the hysteresis. -
4. Pause time calculation
- Pause time: the duration that wipers are stopped at parking position
- Elapsed time: the duration after the wiper motor started to operate from parking position
- The pause time is calculated by the vehicle speed and the VOLUME.

undefined
8710-08
RKSTICS
Front/Center Room Lamp Control
The overhead console lamp (front room lamp) comes on when opening the
door(driver's/passenger's) while the door coupled front rooom lamp switch is at the coupled
operating position and the key reminder switch is "OFF".
When the door (Driver's/Passenger's) is opened, the front room lamp comes on.
The room lamp stays on for 2 seconds and then dims out through 3 seconds when closing
the opened door.
The dimming operation must have greater than 32 steps per one second.
The room lamp output should stop immediately after turning on the ignition key during the
dimming operation.
The front room lamp comes on for 30 seconds when receiving the unlock signal from the
remote control key while the doors are closed.
The front room lamp and the center room lamp output period is extended by 30 seconds
when receiving the unlock signal from the remote control key again during output. (The
lamp stays on when unlocked by the remote control key.)
When a door is opened during its extended period, the lamp stays on. If closed, operates as
in step 2.
The room lamp output stops immediately after receiving the lock signal from
driver's/passenger's door lock switches while the driver's and passenger's doors are closed
or entering into the anti-theft mode by pushing LOCK button on the remote control key.
The front room lamp comes on when opening the driver's door or passenger's door and
goes off when closing the opened door while the ignition key is in ON position. 1.
2.
3.
4.
5.
6.
7.
8.
9.

RKSTICS
undefined
8710-08
Front Room LampCenter Room Lamp
Front room lamp (driver's or passenger's) is
turned on and off when pressing the switch (1 o
r
2). However, it comes on when a door is opened
and goes off when the door is closed. The front
room lamp comes on when opening any of front
doors with the front door coupled switch (3)
pressed in.
If the switch is at the door coupled position,
the center room lamp comes on when a rea
r
door is opened. The lamp always comes on
while the switch is at the other position.
Door coupled
switch
Ignition Key Hole Illumination
The ignition key hole illumination comes on when opening the driver's door or passenger's
door when the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing the door after step
1.
The output stops when the ignition key is turned to "ON" position.
The output stops when receiving the lock signal from the remote control key (under anti-
theft mode). 1.
2.
3.
4.
(*1) OPEN : Driver's or Passenger's door = OPEN, CLOSE : Driver's and Passenger's = CLOSE

RKSTICS
undefined
8710-08
Door Lock/Unlock Control by Door Lock Switch
The door lock system outputs "LOCK" signal for 0.5 seconds when positioning the driver's
or passenger's door lock switch to the lock position.
The door lock system outputs "UNLOCK" signal for 0.5 seconds when positioning the
driver's or passenger's door lock switch to the unlock position.
The door lock system outputs "LOCK" signal for 0.5 seconds when switching from LOCK to
UNLOCK by the driver's or passenger's door key cylinder.
The door lock system outputs "UNLOCK" signal for 0.5 seconds when switching from
UNLOCK to LOCK by the driver's or passenger's door key cylinder.
The alarm will not be activated when switched to UNLOCK by driver's or passenger's doo
r
key cylinder switch in theft deterrent mode.
It does not occur abnormal operation when reconnecting the battery after disconnecting the
battery cable.
All door lock signals are "UNLOCK" for 0.5 seconds just for once when receiving the
"LOCK" signal within 0.5 seconds after closing the driver's or passenger's door while the
ignition key is removed. 1.
2.
3.
4.
5.
6.
7.

undefined
8710-08
RKSTICS
Driver's door lock/unlock switch Passenger's door lock/unlock switch
Door Lock/Unlock by Central Door Lock Switch
The door lock system outputs "LOCK/UNLOCK" signal for 0.5 seconds when operating the
central door lock switch. (However, if the door lock switch (front doors) is at LOCK position,
the system outputs UNLOCK signal, and vice versa.)
The "LOCK" or "UNLOCK" inputs from the central door lock switch in anti-theft mode are
ignored. 1.
2.

undefined
8710-08
RKSTICS
Time Lag Power Window Control
The power window relay output is "ON" when turning on the ignition switch.
The power window relay output is "ON" for 30 seconds when turning off the ignition switch.
The power window relay output is "OFF" when opening the driver's door or the passenger's
door.
The power window relay is turned "OFF" when receiving the remote control key lock signal
(armed mode) during its extended operation period of 30 seconds. 1.
2.
3.
Definition of Terms
DOOR OPEN and DOOR CLOSE
DOOR OPEN: Any of all door switches (including hood and tailgate) is in "OPEN" position.
DOOR CLOSE: All door switches (including hood and tailgate) are in "CLOSE" position. 1.
The door lock/unlock operation does not affect the engine hood.
DOOR LOCK: Indicates that all door lock switches (including tailgate) are in LOCK positions.
DOOR UNLOCK: Indicates that any of all door lock switches (including tailgate) is in UNLOCK
position. 2.

RKSTICS
undefined
8710-08
Power Sleep Mode
1. Entering Condition
1) When all the doors including the hood are closed.
2) When the ignition key is in "OFF" position.
3) When there is no key in the driver's/passenger's door key cylinder.
4) The system enters into the sleep mode for saving power if there is any change for 6
seconds while the driver's/passenger's/rear doors and tailgate are locked with the above
three conditions met.
2. The sleep mode is deactivated immediately if any of them is out of the specified
conditions (wake-up mode).
Also, the sleep mode is deactivated when receiving the UNLOCK signal from the remote
control key.
3. During the sleep mode, the sleep mode is deactivated for 30 seconds when room
lamp, key hole illumination, tail lamp or power window is operated or after the
system receives the UNLOCK signal from the remote control key.
However, if the lamps and power window mentioned above are "OFF" and the conditions in
item (1) are met, the system enters into the sleep mode again.