2006 SSANGYONG REXTON turn signal

RKSTICS
undefined
8710-08
Auto Washer and Wiper Switch
When the auto washer switch is turned on with the ignition switch "ON" and the AUTO
switch "OFF", the washer motor output gets ON for 1 second. If the system recognizes the
output signal, the wiper relay output gets ON during 4 cycles and the washer motor output
gets ON for 1 second. Then, the wiper relay output gets OFF after 3 cycles. 1.

undefined
8710-08
RKSTICS
Auto Switch Position Reminder (Power-Up Reminder Wiper)
When turning off and on the IGN2 switch with the auto switch on, the system drives the
wiper motor through LOW relay one cycle regardless of communication with rain sensor.
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when changing the
auto switch from "OFF" to "ON" position regardless of communication with rain sensor(while
the ignition key is in the "ON" position).
When the auto switch is turned to the "ON" position again from the "OFF" position, the
system drives the wiper motor through LOW relay one cycle only when the rain senso
r
detects the "Rain Detected" signal. 1.
2.

undefined
8710-08
RKSTICS
Washer Coupled Wiper in Rain Sensing Mode
The washer coupled wiper is operated when receiving the washer switch input with the
ignition switch "ON" and the AUTO switch "ON" in the rain sensing mode. At this moment,
the communication with the rain sensor is overridden. However, the washer switch input is
overridden during the continuous operation.
The operation data is sent to the rain sensor even during the washer coupled wiper's
operation. 1.
2.
Rain Sensing Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
sensitivity is increased (while the ignition key is in the "ON" position, the AUTO switch is in
the "ON" position, and the wiper motor is in "Parked" position). However, the wiper moto
r
can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper moto
r
runs only one cycle. *

undefined
8710-08
RKSTICS
Defective Rain Sensor
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction signal from the rain
sensor (while the ignition key is in "ON" position and the AUTO switch is in "ON" position). 1.
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain senso
r
(while the ignition key is in "ON" position and the AUTO switch is in "ON" position). 2.

RKSTICS
undefined
8710-08
Tail Lamp Left On Warning
The buzzer sounds with the interval of 0.3 second when opening the driver's door while the
tail lamp is turned on and the ignition key is removed.
The buzzer output stops when turning off the tail lamp and closing the driver's door.
The system outputs "UNLOCK" signal for 5 seconds when the driver's and passenger's
door lock switch is locked (while the tail lamp is turned on and the driver's door is open).
This function is not available when the ignition key is in the "ON" position. 1.
2.
3.
4.

undefined
8710-08
RKSTICS
Front/Center Room Lamp Control
The overhead console lamp (front room lamp) comes on when opening the
door(driver's/passenger's) while the door coupled front rooom lamp switch is at the coupled
operating position and the key reminder switch is "OFF".
When the door (Driver's/Passenger's) is opened, the front room lamp comes on.
The room lamp stays on for 2 seconds and then dims out through 3 seconds when closing
the opened door.
The dimming operation must have greater than 32 steps per one second.
The room lamp output should stop immediately after turning on the ignition key during the
dimming operation.
The front room lamp comes on for 30 seconds when receiving the unlock signal from the
remote control key while the doors are closed.
The front room lamp and the center room lamp output period is extended by 30 seconds
when receiving the unlock signal from the remote control key again during output. (The
lamp stays on when unlocked by the remote control key.)
When a door is opened during its extended period, the lamp stays on. If closed, operates as
in step 2.
The room lamp output stops immediately after receiving the lock signal from
driver's/passenger's door lock switches while the driver's and passenger's doors are closed
or entering into the anti-theft mode by pushing LOCK button on the remote control key.
The front room lamp comes on when opening the driver's door or passenger's door and
goes off when closing the opened door while the ignition key is in ON position. 1.
2.
3.
4.
5.
6.
7.
8.
9.

RKSTICS
undefined
8710-08
Front Room LampCenter Room Lamp
Front room lamp (driver's or passenger's) is
turned on and off when pressing the switch (1 o
r
2). However, it comes on when a door is opened
and goes off when the door is closed. The front
room lamp comes on when opening any of front
doors with the front door coupled switch (3)
pressed in.
If the switch is at the door coupled position,
the center room lamp comes on when a rea
r
door is opened. The lamp always comes on
while the switch is at the other position.
Door coupled
switch
Ignition Key Hole Illumination
The ignition key hole illumination comes on when opening the driver's door or passenger's
door when the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing the door after step
1.
The output stops when the ignition key is turned to "ON" position.
The output stops when receiving the lock signal from the remote control key (under anti-
theft mode). 1.
2.
3.
4.
(*1) OPEN : Driver's or Passenger's door = OPEN, CLOSE : Driver's and Passenger's = CLOSE

undefined
8710-08
RKSTICS
Auto Door Lock
The door lock system outputs "LOCK" when the vehicle speed maintains over 50 km/h.
However, it doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times
(except step 1) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door is regarded as "FAIL".
If the door that was regarded as fail changes (UNLOCK to LOCK) to unlock, only one
"LOCK" output will be done.
If any door is regarded as FAIL, the auto door lock function does not work (if it is occurred
when the vehicle speed is over 50 km/h, the auto door lock output does not occur even i
f
the vehicle speed falls below 50 km/h and accelerates again to over 50 km/h.).
Nonetheless, the central door lock function works properly.
When the system receives "UNLOCK" signal from a door switch, it outputs "LOCK" signals 5
times. If additional "LOCK" signal from another door switch is detected during the period, the
system outputs five "LOCK" signals
5 times for the door system outputs five "LOCK" signals 5 times for the door.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled (IGN1=OFF) (even when there is no "LOCK"
output while the vehicle speed maintains over 50 km/h under lock condition).
(If the LOCK condition is established with the ignition switch ON, the system outputs
UNLOCK signal unconditionally when turning the ignition switch to OFF position.)
However, when the ignition key is turned to "OFF" position, the lock output conditions will be
cancelled.
The "FAIL" condition of the door will be erased when the ignition key is turned to "OFF"
position. 1.
2.
3.
4.
5.
6.
7.
8.