2006 SAAB 9-2X ECU

Maintenance and service
11 - 3 9
11
– CONTINUED –
2. Pull the blade rubber assembly out of
the plastic support.1) Metal spines3. If the new blade rubber is not provided
with two metal spines, remove the metal
spines from the old blade rubber and in-
stall them in the new blade rubber.4. Align the claws of the plastic support
with the grooves in the blade rubber as-
sembly, then slide the blade rubber as-
sembly into place.
Securely retain both ends of the rubber
with the stoppers on the plastic supportends. If the rubber is not retained properly,
the wiper may scratch the rear window
glass.
5. Install the wiper blade assembly to the
wiper arm. Make sure that it locks in place.
6. Hold the wiper arm by hand and slowly
lower it in position.
B00505
1
B00066B00067
A1910BE-A-GSAAB.book Page 39 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 4 7
11
– CONTINUED –
1. Remove the air intake duct mounting
bolt, then remove the air intake duct.
2. Remove the bulb cover by turning it
counterclockwise.3. Push the retainer spring in the direction
of the arrow to remove it from the hook.
4. Pull the bulb out of the electrical con-
nector. Replace the bulb with a new one.
5. Set the retainer spring securely.
6. Reconnect the electrical connector.7. Install the bulb cover.

Left-hand low beam light bulb

High beam light bulbs
0
1. Remove the bulb from the headlight
assembly by turning it counterclockwise.
B00485B00486
700092B00488
Replacement of the left-hand low
beam light bulb requires removal of
the battery and is thus dangerous. It
must be performed by a Saab deal-
er.
B00489
A1910BE-A-GSAAB.book Page 47 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 5 0
Maintenance and service
1) Front side marker light
2) Front turn signal light4. Lift the undercover. Insert your hand
under the undercover and feel for the front
turn signal light and front side marker light
with reference to the following illustration.
Remove the bulb socket from the head-
light assembly by turning it counterclock-
wise.
1) Front turn signal light
2) Front side marker light5. Pull the bulb out of the socket. Install a
new bulb.

Rear combination lights1. Using a Phillips screwdriver, remove
the upper and lower clips that secure the
side cover of the rear combination light as-
sembly.
1
2
B00494
1
2
B00495
B00496B00529
A1910BE-A-GSAAB.book Page 50 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 5 1
11
– CONTINUED –
2. Remove the side cover.
3. Remove the upper and lower bolts.
Then, slide the rear combination lamp as-
sembly to the rear and remove it from the
vehicle.
1) Rear turn signal light
2) Brake/tail light
3) Backup light4. Remove the bulb socket from the rear
combination light assembly by turning it
counterclockwise.
5. Pull the bulb out of the bulb socket and
replace it with a new one.
6. Set the bulb socket into the rear combi-
nation light assembly and turn it clockwise
until it locks.7. Put the rear combination light assem-
bly into place while aligning the clip with
the guide on the vehicle and fasten the
bolts.
8. Install the side cover and secure it with
the clips.
B00497
1
2
3
B00498
B00534
A1910BE-A-GSAAB.book Page 51 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com