2006 RENAULT SCENIC sat nav

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C-25
NAV 4R
Program no.: 0000
Vdiag No.: 24
DF030
CONTINUED 2
If the connections are correct, replace component 1551 or 886.
Mégane II ph2
(see MR 364 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Laguna II ph2
(see MR 395 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Scénic II ph2
(see MR 370 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Trafic II ph1 and ph2
(see MR 408 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Master ph2 and ph3
(see MR 377 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Master propulsion ph2
(see Technical Note 3818A, 83C On-board telematics system, Navigation aerial: Removal - Refitting).
Look for any damage to the coaxial cable.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the faults from the 4R radio navigation computer memory using command RZ001
Fault memory.
Check the number of satellites received from outside, with the system switched on for
10 minutes, followed by a new check with the diagnostic tool.

MULTIMEDIA
Fault finding - Conformity check
86C
86C-29
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Conformity check
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine stopped, ignition on.
Order FunctionParameter / Status
checked or ActionDisplay and Notes Fault finding
1
Power supplyET001:+ 12 V after
ignition feedPRESENTIn the event of a fault, refer to
the interpretation of status
ET001 + 12 V after ignition
feed.
2ET002:+ 12 V
accessories
feedPRESENTIn the event of a fault, refer to
the interpretation of status
ET002 + 12 V accessories
feed.
3ET003:+ 12 V side
lights feedPRESENT
ABSENTIn the event of a fault, consult
the interpretation of status
ET003 + 12 V side lights
feed.
4PR001:Battery
voltage11 V < PR001 < 14 VIn the event of a fault, refer to
the interpretation of
parameter PR001 Battery
voltage.
5Vehicle
speedPR002:Vehicle
speedUnit: km/hIn the event of a fault, consult
the interpretation of
parameter PR002 Vehicle
speed.
6External
temperature
sensorPR006:External
temperaturePR006 = External
temperature sensor ±± ± ±
5 °° ° °
CIn the event of a fault, refer to
the interpretation of
parameter PR006 External
temperature.
7Angular
position
sensorPR009:Angular
positionUnit: *d/s
This parameter determines
The angular speed when
cornering.In the event of a fault, consult
the interpretation of
parameter PR009 Angular
position.
8Satellite
receptionPR008:Satellite
number
receivedIn an open area, the
number of satellites
received should be greater
than 3 for the system to
operate correctly.In the event of a fault, consult
the interpretation of
parameter PR008 Number of
satellites received.
9OffET004:RADIO ON
signalSTILL PRESENTIf the fault is still present,
contact Techline.
NAV4R_V24_CCONF

MULTIMEDIA
Fault finding - Conformity check
86C
86C-31
NAV 4R
Program no.: 0000
Vdiag No.: 24
Sub-function: USER SELECTION (CONTINUED)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine stopped, ignition on.
Order FunctionParameter / Status
checked or ActionDisplay and Notes Fault finding
14
Front panel
button
(continued)ET033:Directional buttonPRESSED
RELEASED
If the fault is still present,
contact Techline. 15 ET034:Mode buttonPRESSED
RELEASED
16 ET039:Front panel rotary
button actuationPRESSED
RELEASED
17Steering
wheel
controlsET037:Satellite wheelA variation from 0 to
+ 3 in one direction and
from 0 to - 3 in the
other direction
confirms that the wheel
is operating correctly.In the event of a fault, consult
the interpretation of status
ET037 Satellite wheel.
18Front panel
buttonET038:Front panel rotary
button
If the fault is still present,
contact Techline.
19CDAC022:CD ejectionThis command is used
to eject the CD from
the CD reader.

MULTIMEDIA
Fault finding - Status summary table86C
86C-34
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Status summary table
Tool status Diagnostic tool title
ET001+ 12 V after ignition feed
ET002+ 12 V accessories feed
ET003+ 12 V side lights feed
ET004RADIO ON signal
ET006+ button
ET007- button
ET008Top button
ET009High button
ET010Low button
ET014Source button
ET026Radio on/off button
ET027CD eject button
ET028Tone button
ET029Voice synthesiser button
ET030Station preselection button
ET032Navigation button
ET033Directional button
ET034Mode button
ET036MUTE button
ET037Satellite wheel
ET038Front panel rotary button
ET039Front panel rotary button actuation

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-42
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET006
ET007
ET008
ET009
ET010
ET036
CONTINUED 3
If the measured values do not correspond with the values above, replace the radio satellite control.
Mégane II ph2 (see MR 364 mechanical, 84A Control - Signals, Steering wheel controls: Removal -
Refitting).
Laguna II ph2 (see MR 395 mechanical, 84A Control - Signals, Steering wheel controls: Removal - Refitting).
Scénic II ph2 (see MR 370 mechanical, 84A Control - Signals, Steering wheel controls: Removal - Refitting).
Master ph2 and ph3
(see MR 377 mechanical, 86A, Radio control satellite: Removal - Refitting).
Master propulsion ph2
(see Technical Note 3818A, 86A, Radio, Radio control satellite: Removal - Refitting).
Trafic II ph1 and ph2
(see MR 408 mechanical, 86A, Radio control satellite: Removal - Refitting).
If the measurements are in order, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-43
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET037
SATELLITE WHEEL
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition and connection of the connector of component 325 (Scénic: 1519) and the black 24-track
connector of component 261 (commercial vehicle: 662).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_ET037

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-45
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET037
CONTINUED 2
Check that the wheel is operating correctly by checking the continuity between the following connections:
●34AR and 34AT
●34AR and 34AU
●34AR and 34AS
on component 325 (Scénic: 1519).
If there is no continuity, replace component 325 (Scénic: 1519).
Mégane II ph2 (see MR 364 mechanical, 84A Control - Signals, Steering wheel controls: Removal -
Refitting).
Laguna II ph2 (see MR 395 mechanical, 84A Control - Signals, Steering wheel controls: Removal - Refitting).
Scénic II ph2 (see MR 370 mechanical, 84A Control - Signals, Steering wheel controls: Removal - Refitting).
Master ph2 and ph3 (see MR 377 mechanical, 86A Radio, Radio control satellite: Removal - Refitting).
Master propulsion ph2 (see Technical Note 3818A, 86A, Radio, Radio control satellite: Removal - Refitting).
Trafic II ph1 and ph2 (see MR 408 mechanical, 86A Radio, Radio control satellite: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.

MULTIMEDIA
Fault finding - Parameter summary table86C
86C-46
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Battery voltage
PR002Vehicle speed
PR006External temperature
PR008Number of satellites received
PR009Angular position
PR010Radio field intensity