2006 NISSAN VERSA wiring
[x] Cancel search: wiringPage 2209 of 2896
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
HEADLAMP (FOR USA) ............................................ 5
Component Parts and Harness Connector Location ..... 5
System Description .................................................. 5
OUTLINE ............................................................... 5
HEADLAMP OPERATION .................................... 6
COMBINATION SWITCH READING FUNCTION ..... 6
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 6
CAN COMMUNICATION SYSTEM DESCRIP-
TION ......................................................................... 6
Schematic ................................................................ 7
Wiring Diagram ........................................................ 8
Terminals and Reference Values for BCM ............. 12
Terminals and Reference Values for IPDM E/R ..... 12
How to Perform Trouble Diagnoses ....................... 12
Preliminary Check .................................................. 12
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM .................................................. 12
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R .......................................... 12
CONSULT-II Function (BCM) ................................. 12
CONSULT-II START PROCEDURE .................... 12
WORK SUPPORT ............................................... 12
DATA MONITOR ................................................. 12
ACTIVE TEST ..................................................... 13
SELF-DIAGNOSTIC RESULTS .......................... 13
CONSULT-II Function (IPDM E/R) ......................... 13
CONSULT-II START PROCEDURE .................... 13
DATA MONITOR ................................................. 14
ACTIVE TEST ..................................................... 14
Headlamp High Beam Does Not Illuminate (Both
Sides) ..................................................................... 14
Headlamp High Beam Does Not Illuminate (One
Side) ....................................................................... 17
High Beam Indicator Lamp Does Not Illuminate .... 18
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 18Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 21
Headlamps Do Not Turn OFF ................................. 22
Aiming Adjustment .................................................. 23
PREPARATION BEFORE ADJUSTING .............. 23
LOW BEAM AND HIGH BEAM ........................... 23
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 24
Bulb Replacement .................................................. 25
HEADLAMP (HIGH/LOW) ................................... 25
PARKING (CLEARANCE) LAMP ........................ 25
FRONT TURN SIGNAL LAMP ............................ 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Disassembly and Assembly .................................... 26
DISASSEMBLY ................................................... 26
ASSEMBLY ......................................................... 26
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 27
Component Parts and Harness Connector Location ... 27
System Description ................................................. 27
OUTLINE ............................................................. 27
HEADLAMP OPERATION ................................... 28
COMBINATION SWITCH READING FUNCTION ... 29
EXTERIOR LAMP BATTERY SAVER CONTROL ... 29
CAN Communication System Description .............. 29
Schematic ............................................................... 30
Wiring Diagram — DTRL — ................................... 31
Terminals and Reference Values for BCM .............. 35
Terminals and Reference Values for IPDM E/R ...... 35
How to Perform Trouble Diagnoses ....................... 35
Preliminary Check .................................................. 35
CHECK BCM CONFIGURATION ........................ 35
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM .................................................. 35
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R .......................................... 35
CONSULT-II Function (BCM) ................................. 35
CONSULT-II Function (IPDM E/R) ......................... 35
Page 2210 of 2896
LT-2Revision: June 20062007 Versa Daytime Light Control Does Not Operate Properly
(High Beam Headlamps Operate Properly) ............ 35
Aiming Adjustment .................................................. 37
PREPARATION BEFORE ADJUSTING .............. 37
LOW BEAM AND HIGH BEAM ........................... 37
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 38
Bulb Replacement .................................................. 39
HEADLAMP (HIGH/LOW) ................................... 39
PARKING (CLEARANCE) LAMP ......................... 39
FRONT TURN SIGNAL LAMP ............................ 39
Removal and Installation ........................................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
Disassembly and Assembly .................................... 40
DISASSEMBLY ................................................... 40
ASSEMBLY ......................................................... 40
FRONT FOG LAMP .................................................. 41
Component Parts and Harness Connector Location ... 41
System Description ................................................. 41
OUTLINE ............................................................. 41
FOG LAMP OPERATION .................................... 42
COMBINATION SWITCH READING FUNCTION ... 42
EXTERIOR LAMP BATTERY SAVER CONTROL ... 42
CAN Communication System Description .............. 42
Wiring Diagram — F/FOG — .................................. 43
Terminals and Reference Values for BCM .............. 45
Terminals and Reference Values for IPDM E/R ...... 45
How to Proceed With Trouble Diagnosis ................ 45
Preliminary Check .................................................. 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ........................................... 45
CONSULT-II Function (BCM) .................................. 45
CONSULT-II Function (IPDM E/R) .......................... 45
Front Fog lamps Do Not Illuminate (Both Sides) .... 45
Front Fog Lamp Does Not Illuminate (One Side) ... 48
Aiming Adjustment .................................................. 49
Bulb Replacement .................................................. 49
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
TURN SIGNAL AND HAZARD WARNING LAMPS ... 51
Component Parts and Harness Connector Location ... 51
System Description ................................................. 51
TURN SIGNAL OPERATION ............................... 51
HAZARD LAMP OPERATION ............................. 52
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION .................................................................... 53
COMBINATION SWITCH READING FUNCTION ... 53
CAN Communication System Description .............. 53
Schematic ............................................................... 54
Wiring Diagram — TURN — ................................... 55
Terminals and Reference Values for BCM .............. 59
How to Proceed With Trouble Diagnosis ................ 59
Preliminary Check .................................................. 59
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 59CONSULT-II Function (BCM) ..................................59
Turn Signals Do Not Operate ..................................59
Front Turn Signal Lamp Does Not Operate ............59
Rear Turn Signal Lamp Does Not Operate .............60
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operates ............................................62
Turn Signal Indicator Lamp Does Not Operate .......63
Bulb Replacement of Front Turn Signal Lamp ........64
Bulb Replacement of Rear Turn Signal Lamp .........64
Removal and Installation of Front Turn Signal Lamp ...64
Removal and Installation of Rear Turn Signal Lamp ...64
LIGHTING AND TURN SIGNAL SWITCH ................65
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
HAZARD SWITCH .....................................................66
Removal and Installation .........................................66
REMOVAL ............................................................66
INSTALLATION ....................................................66
COMBINATION SWITCH ..........................................67
Wiring Diagram — COMBSW — ............................67
Combination Switch Reading Function ...................68
Terminals and Reference Values for BCM ..............68
CONSULT-II Function (BCM) ..................................68
Combination Switch Inspection ...............................68
Removal and Installation .........................................70
STOP LAMP ..............................................................71
Wiring Diagram — STOP/L — ................................71
Bulb Replacement of High-Mounted Stop Lamp .....72
Bulb Replacement of Rear Combination Lamp for
Stop Lamp ...............................................................72
Removal and Installation of High-Mounted Stop
Lamp .......................................................................72
REMOVAL ............................................................72
INSTALLATION ....................................................72
Removal and Installation of Rear Combination
Lamp for Stop Lamp ................................................72
BACK-UP LAMP .......................................................73
Wiring Diagram — BACK/L — ................................73
Bulb Replacement ...................................................74
Removal and Installation .........................................74
PARKING, LICENSE PLATE AND TAIL LAMPS ......75
Component Parts and Harness Connector Location ...75
System Description .................................................75
OPERATION BY LIGHTING SWITCH .................75
COMBINATION SWITCH READING FUNCTION ...76
EXTERIOR LAMP BATTERY SAVER CONTROL ...76
CAN Communication System Description ..............76
Schematic ...............................................................77
Wiring Diagram — TAIL/L — ...................................78
Terminals and Reference Values for BCM ..............81
Terminals and Reference Values for IPDM E/R ......81
How to Proceed With Trouble Diagnosis ................81
Preliminary Check ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ...........................................81
CONSULT-II Function (BCM) ..................................81
Page 2211 of 2896
LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa CONSULT-II Function (IPDM E/R) ......................... 81
Parking, License Plate and Tail Lamps Do Not Illu-
minate .................................................................... 81
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) ............................. 85
Bulb Replacement .................................................. 86
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
Removal and Installation ........................................ 86
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
REAR COMBINATION LAMP .................................. 87
Components ........................................................... 87
Bulb Replacement .................................................. 87
Removal and Installation ........................................ 87
REMOVAL ........................................................... 87
INSTALLATION ................................................... 87
Disaassembly and Assembly ................................. 87
DISSASEMBLY ................................................... 87
ASSEMBLY ......................................................... 88
INTERIOR LAMP ...................................................... 89
Map lamp ............................................................... 89
BULB REPLACEMENT ....................................... 89
REMOVAL AND INSTALLATION ........................ 89
DISASSEMBLY AND ASSEMBLY ...................... 89
Luggage Compartment Lamp ................................ 90
BULB REPLACEMENT ....................................... 90
REMOVAL AND INSTALLATION ........................ 90
INTERIOR ROOM LAMP .......................................... 91
Component Parts and Harness Connector Location ... 91
System Description ................................................ 91
POWER SUPPLY AND GROUND ...................... 91
SWITCH OPERATION ........................................ 92
INTERIOR ROOM LAMP TIMER OPERATION ... 93
INTERIOR LAMP BATTERY SAVER CONTROL ... 94Schematic ............................................................... 95
Wiring Diagram — INT/L — .................................... 96
Terminals and Reference Values for BCM ............101
How to Proceed With Trouble Diagnosis ..............101
Preliminary Check ................................................101
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................101
CONSULT-II Function (BCM) ...............................101
CONSULT-II START PROCEDURE ..................101
WORK SUPPORT .............................................101
DATA MONITOR ...............................................101
ACTIVE TEST ...................................................102
WORK SUPPORT .............................................102
DATA MONITOR ...............................................102
Interior Room Lamp Control Does Not Operate
(With Map Lamp) ..................................................103
Interior Room Lamp Control Does Not Operate
(Without Map Lamp) .............................................105
Bulb Replacement ................................................107
ROOM LAMP ....................................................107
Removal and Installation ......................................107
ROOM LAMP ....................................................107
ILLUMINATION .......................................................108
System Description ...............................................108
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................108
EXTERIOR LAMP BATTERY SAVER CONTROL .109
CAN Communication System Description ............109
Schematic .............................................................110
Wiring Diagram — ILL — .......................................111
Bulb Replacement ................................................115
GLOVE BOX LAMP ...........................................115
BULB SPECIFICATIONS ........................................116
Headlamp .............................................................116
Exterior Lamp .......................................................116
Interior Lamp/Illumination .....................................116
Page 2212 of 2896
LT-4
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS00IM8
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Page 2216 of 2896
LT-8
HEADLAMP (FOR USA)
Revision: June 20062007 Versa
Wiring Diagram EKS00HVG
LKWA0318E
Page 2239 of 2896
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LT-31
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
Wiring Diagram — DTRL —EKS00ICI
LKWA0322E
Page 2251 of 2896
FRONT FOG LAMP
LT-43
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
Wiring Diagram — F/FOG —EKS00HXA
LKWA0326E
Page 2263 of 2896
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
Wiring Diagram — TURN —EKS00HY4
LKWA0329E