COMBINATION METER
CHASSIS ELECTRICAL54A-10
COMBINATION METER
M2540005000894
The combination meter features large, clearly visible
analogue indicators. The meter has the speedometer
in the middle, the coolant temperature gauge at
upper right, the fuel gauge at lower right, and the
tachometer at left so that drivers can easily distin
-
guish the information from the meters. The combina-
tion meter offers the following advantages.
•The combination meter is used for air conditioner
and meter drive control to integrate ECU.
•CAN communication is used for more reliable
transmission of all gauge data and indicator lamp
input signals, such as vehicle speed, engine
RPM, and coolant temperature. For further
details on CAN, refer to GROUP 54C, CAN
P.54C-2. The signals that the combination meter
uses are described in the CAN communications
input signals table
.
•Several diagnosis functions such as the diagno-
sis code memory and actuator tests are prepared
in order to improve serviceability.
•For a brighter display at night and for a longer
useful life, all indicator lamps, warning lamps, and
illumination bulbs use LEDs.
•The indicators for the speedometer, fuel gauge,
and other gauges are driven by a stepping motor.
For further details, consult the stepping motor
section
.
•The electronic speedometer operates by receiv-
ing vehicle speed signals sent by the
engine-ECU or engine-CVT-ECU
via the CAN.
•A large and clear LCD type odo-tripmeter is pro-
vided. The odometer continuously displays val-
ues while the tripmeter adopts a twin-trip (trip A,
trip B) function which is switched by a reset but
-
ton. In addition, clock function is incorporated.
•A fog lamp indicator lamp is provided to let the
driver know that the fog lamp is on.
•A seat belt warning lamp is installed to encourage
the driver to fasten the seat belt.
•The high-contrast meter is adopted. When the
ignition is turned ON, such as the needles and
face display are illuminated with fade-in lighting
by the LED light source.
•To further accentuate the high-contrast lighting,
the light of the high-contrast meter fades in and
fades out when the light is turned on and off
respectively.
•With the auto illumination function incorporated in
the high-contrast meter, a two-stage switching of
daytime (non-dimming) and nighttime (dimming)
is achieved. Also, the brightness can be adjusted
using the illumination control knob.
•A tail lamp indicator lamp is installed which
informs the lighting status of the tail lamps to the
driver.
DIAGNOSTIC FUNCTION
SMART WIRING SYSTEM (SWS)54B-9
Driver's door lock actuator
switchMove the door lock knob or driver’s door key cylinder
from lock position to unlock position or vice versafrom ON to OFF or
from OFF to ON
Driver's door unlock actuator
switchfrom OFF to ON or
from ON to OFF
Power window timer duration*1When the power window timer is activatedDisplays the
operation duration
Column
switchTail lamp switchWhen the lighting switch is turned from one position to
the tail lamp positionfrom OFF to ON
Headlamp
switchWhen the lighting switch is turned from one position to
the headlamp position
Dimmer switchWhen the switch is turned from the OFF to the ON
position
Passing switch
Turn signal
lamp LH switch
Turn signal
lamp RH switch
Headlamp specification*1The display alters according to the headlamp
specification ("4 BULBS" or "2 BULBS").4 BULBS
Column
switch (wiper
switch)Windshield
mist wiper
switchWhen the switch is turned from OFF to ONfrom OFF to ON
Windshield
intermittent
wiper switch
Windshield low
speed wiper
switch
Windshield
high speed
wiper switch
Windshield
washer switch
Rear wiper
switch
Rear washer
switch
Windshield
intermittent
wiper volumeWhen the interval adjusting knob is turned from
"FAST" to "SLOW" while the ignition switch is ON.Displays the
windshield
intermittent wiper
volume voltage
Wiper
autostop
signalFrontWhen activated from the stopped conditionfrom OFF to ON
Rear
Input signal Condition for sounding buzzer Display on
M.U.T.-III (when
SWS monitor is
used)
