2006 MERCEDES-BENZ R500 start stop button

39 Getting started
Unlocking
SmartKey with KEYLESS-GO*
Vehicles equipped with the KEYLESS-GO
feature are supplied with a SmartKey with
integrated KEYLESS-GO function and a re-
movable KEYLESS-GO start / stop button.
With the KEYLESS-GO start/stop button
inserted and the SmartKey with
KEYLESS-GO present in the vehicle, press-
ing the KEYLESS-GO start/stop button

without the brake pedal depressed
corresponds to the various starter
switch positions (
page 40)


with the brake pedal firmly depressed
will start the engine (
page 54)
If you wish or should there be a need to in-
sert the SmartKey with KEYLESS-GO in the
starter switch, the KEYLESS-GO start/stop
button can be easily removed by pulling it
out of the starter switch.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be
sufficiently charged.

Check the battery and charge it if
necessary (
page 487).


Get a jump start (
page 496).
To prevent accelerated battery dis-
charge or a completely discharged bat-
tery, always remove the SmartKey from
the starter switch when the engine is
not in operation.
iThe KEYLESS-GO start/stop button
does not need to be removed from the
starter switch when you leave the vehi-
cle. However, always take the
SmartKey with KEYLESS-GO with you
when you leave the vehicle. As long as
the SmartKey with KEYLESS-GO is in
the vehicle, the vehicle’s electrical sys-
tems can be switched on or the engine
can be started using the KEYLESS-GO
start/stop button.

40 Getting startedUnlocking1KEYLESS-GO start/stop button
2Starter switchKEYLESS-GO start / stop button3USA only
4Canada onlyThe SmartKey with KEYLESS-GO must be
located in the vehicle.

Insert KEYLESS-GO start/stop
button1 into starter switch 2 (if not
inserted already).

Make sure the automatic transmission
is set toP.

Do not depress the brake pedal.
Position 0
Before you press the KEYLESS-GO
start/stop button, the vehicle’s on-board
electronics have status0 (as with
SmartKey removed).
Position 1

Press the KEYLESS-GO start/stop but-
ton once.
This supplies power for some electrical
consumers, such as seat adjustment.Ignition (or Position 2)

Press the KEYLESS-GO start / stop but-
ton twice.
This supplies power for all electrical
consumers.
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 404).
iIf you now press the KEYLESS-GO
start/stop button

once more, the ignition (position2)
is switched on


twice more, the power supply is
again switched off

41 Getting started
Unlocking
For information on starting the engine
using the KEYLESS-GO start / stop button,
see “Starting with KEYLESS-GO*”
(page 54).
For more information on KEYLESS-GO, see
“SmartKey with KEYLESS-GO*”
(page 114).
iIf you now press the KEYLESS-GO
start / stop button once more, the pow-
er supply is again switched off.iWhen you switch on the ignition, the in-
dicator and warning lamps (except high
beam headlamp indicator lamp and
turn signal indicator lamps unless acti-
vated) in the instrument cluster come
on. The indicator and warning lamps
(except high beam headlamp indicator
lamp, and turn signal indicator lamps if
activated) will go out when the engine
is running. This indicates that the re-
spective systems are operational.

54 Getting startedDrivingStarting with the SmartKey
Make sure the automatic transmission
is set toP.
The gear position indicator in the multi-
function display should be on
P.

Do not depress the accelerator.

Turn the SmartKey in the starter switch
to position3 (
page 38) and hold until
the engine starts.
For information on turning off the engine
with the SmartKey, see “Turning off the en-
gine” (
page 66).Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start / stop button in the
starter switch.
The SmartKey with KEYLESS-GO must be
located in the vehicle.
KEYLESS-GO start/stop button1USA only
2Canada only
Make sure KEYLESS-GO start/stop
button 1 is inserted in the starter
switch (
page 40).

Make sure the automatic transmission
is set toP.
The gear position indicator in the multi-
function display should be on
P.

Depress the brake pedal during the
starting procedure.

Do not depress the accelerator.
iYou can also use the “touch-start”
function. Turn the SmartKey to
position3 and release it again immedi-
ately. The engine then starts automati-
cally.
Warning!
G
As long as the SmartKey with KEYLESS-GO
is in your vehicle, the vehicle can be started.
Therefore, never leave children unattended
in the vehicle, as they could otherwise acci-
dentally start the engine.
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle.

55 Getting started
Driving

Press KEYLESS-GO start / stop
button1 once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off with
KEYLESS-GO*” (
page 66).Starting difficulties
If the engine does not start as described,
carry out the following steps:

If you are starting the engine with the
SmartKey, turn SmartKey in starter
switch to position0 and repeat starting
procedure.

If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO.
Or:

Remove KEYLESS-GO start / stop
button from starter switch.

Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.

Repeat the starting procedure
(page 54). Remember that extended
starting attempts can drain the battery.

Get a jump start (
page 496).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.

Notify an authorized Mercedes-Benz
Light Truck Center.
iIf you wish to start the vehicle using the
SmartKey instead of the KEYLESS-GO
feature, remove the KEYLESS-GO
start/stop button from the starter
switch (
page 40).

61 Getting started
Driving
Rear window wiper/washer
The combination switch is located on the
left of the steering column.Combination switch1Rear window wiper switch
2Wiping rear window with washer fluid
3Intermittent wiping
4Rear window wiper off
5Wiping rear window with washer fluid
!If anything blocks the windshield
wipers (leaves, snow, etc.), switch
them off immediately.

For safety reasons, stop the vehicle
in a safe location and

remove the SmartKey from the
starter switch
or


turn off the engine by pressing
the KEYLESS-GO* start/stop
button and open the driver’s
door (with the driver’s door
open, starter switch is in
position0, same as with
SmartKey removed from starter
switch)
before attempting to remove any
blockage.


Remove blockage.


Turn the windshield wipers on
again.
If the windshield wipers fail to function
at all in combination switch positionI,


set the combination switch to the
next higher wiper speed


have the windshield wipers
checked at the nearest authorized
Mercedes-Benz Light Truck Center

64 Getting startedParking and lockingYou have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.Warning!
G
With the engine not running, there is no
power assistance for the brake and the
steering system. In this case, it is important
to keep in mind that a considerably higher
degree of effort is necessary to brake and
steer the vehicle.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before turning off
the engine and leaving the vehicle always:

Keep right foot on brake pedal.


Firmly depress parking brake pedal.


Shift the automatic transmission to
positionP.


Slowly release brake pedal.


When parked on an incline, turn front
wheel towards the road curb.


Turn the SmartKey in the starter switch
to position0 and remove the SmartKey
from the starter switch, or press the
start / stop button (vehicles with
KEYLESS-GO*).


Take the SmartKey or the SmartKey with
KEYLESS-GO* and lock vehicle when
leaving.

66 Getting startedParking and lockingTurning off the engine
Shift the automatic transmission to
positionP (
page 199).

Apply the parking brake (
page 65).Turning off with the SmartKey

Turn the SmartKey in the starter switch
to position0 (
page 38).

Remove the SmartKey from the starter
switch.
The immobilizer is activated.Turning off with KEYLESS-GO*

Press the KEYLESS-GO start / stop
button (
page 40) to turn off the
engine.
With the driver's door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch
(
page 38).
iAlways set the parking brake in addi-
tion to shifting to position
P
(
page 199).
When parked on an incline, also turn
front wheel towards the road curb.
iIf you turn off the engine using the
SmartKey and remove the SmartKey
from the starter switch with the trans-
mission in a position other than P, the
transmission will automatically shift
toP.
Keep in mind that turning off the engine
with the SmartKey alone will not auto-
matically shift the transmission to P.
Only when the SmartKey is removed
from the starter switch will the trans-
mission automatically shift to P.
iIf you turn off the engine using the
KEYLESS-GO start/stop button and
open the driver’s door with the trans-
mission in a position other than P, the
transmission will automatically shift
toP.
Keep in mind that turning off the engine
with the KEYLESS-GO start/stop
button alone will not automatically shift
the transmission to P. Only when the
driver’s door is opened will the trans-
mission automatically shift to P.