2006 MERCEDES-BENZ G500 remote start

34 Getting started
The “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation given here.
If you are already familiar with the basic
functions described here, the “Controls in
detail” section will help you with further in-
formation. The corresponding page refer-
ences are at the end of each segment.
Unlocking
Unlocking with the SmartKey
SmartKey with remote control
1‹Lock button
2ŒUnlock button
3ÂPanic button (
page 79)
Press unlock button Πon the
SmartKey.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is dis-
armed.
Get in the vehicle and insert the
SmartKey in the starter switch.
For more information, see “Locking and
unlocking” (
page 92).

92 Controls in detail
In the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed in your vehicle.
If you are already familiar with the basic
functions of your vehicle, this section will
be of particular interest to you.
To quickly familiarize yourself with the ba-
sic functions of the vehicle, refer to the
“Getting started” section of this manual.
The corresponding page numbers are giv-
en at the beginning of each segment.
Locking and unlocking
SmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key. The locking
tabs for the mechanical key portion of the
two SmartKeys are a different color to help
distinguish each SmartKey unit.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks:

the doors

the tailgate

the fuel filler flap
SmartKey with remote control
1‹ Lock button
2Locking tab for mechanical key
3ΠUnlock button
4Battery check lamp
5Â Panic button (
page 79)
i
You can also open and close the power
windows (
page 176) and tilt/sliding
sunroof (
page 179) using the
SmartKey.

99 Controls in detail
Locking and unlocking
Locking and unlocking from the inside
You can lock or unlock the vehicle from in-
side using the central locking switches.
This can be useful, for example, if you want
to unlock the passenger door from the in-
side or want to lock the vehicle before
starting to drive.
The fuel filler flap cannot be locked or un-
locked with the central locking switch.The central locking switch is located in the
center console.
Central locking switch
1Locking
2Unlocking
Locking
Press central locking switch1.
If all the doors and the tailgate are
closed, the vehicle locks.Unlocking
Press central locking switch2.
The vehicle unlocks.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Unsuper-
vised use of vehicle equipment may cause
an accident and/or serious personal injury.
i
You can open a locked door from the
inside. Open door only when conditions
are safe to do so.
If the vehicle was previously centrally
locked using the SmartKey, it will not
unlock using the central locking switch.
If the vehicle was previously locked
with the central locking switch

while in the selective remote con-
trol mode, only the door opened
from the inside is unlocked.

while in the global remote control
mode, the complete vehicle is un-
locked when a door is opened from
the inside.

213 Controls in detail
Useful features
Step 3:
Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the overhead control panel,
keeping the indicator lamp1 in view.
Step 4:
Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3,
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:
Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.Step 7:
To program the remaining two buttons,
repeat the steps above starting with
step 3.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
i
The indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
i
If the indicator lamp1 blinks rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code” feature.


214 Controls in detail
Useful features
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn”or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual.
Step 9:
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:
Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (2, 3,
or4).
Step 11:
Press, hold for two seconds and re-
lease same button a second time to
complete the training process.Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.
Step 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3,
or4).
Step 13:
To program the remaining two buttons,
repeat the steps above starting with
step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Continue to press and hold the inte-
grated signal transmitter button (2,
3, or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.


215 Controls in detail
Useful features
Operation of integrated remote control
Switch on the ignition (page 35).
Select and press the appropriate inte-
grated signal transmitter button (2,
3, or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 35).
Simultaneously hold down the signal
transmitter buttons2 and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated sig-
nal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Press and hold the desired signal trans-
mitter button (2, 3, or4). Do not re-
lease the button.
The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
Heated steering wheel
The steering wheel heater warms up the
leather area of the steering wheel.
The lever with the heated steering wheel
switch is on the lower left-hand side of the
steering wheel.
1Switching on
2Switching off
3Indicator lampi
If you sell your vehicle, erase the codes
of all three channels.

395 Index
Driving
General instructions 43, 220
In winter 225
Problems 55
Safety systems 80
Through standing water 226
Driving abroad 236
Driving and safety systems
4-ETS 83
ABS 80
BAS 82
EBB 84
ESP 84
Driving instructions 220
Passenger compartment 227
Driving off 222
Driving systems 181
Cruise control 181
Driving safety systems 80
Driving through water 231
E
Easy-entry/exit feature 100
Activating 143
EBB 80, 84
Electrical fuses 362
Electrical outlet 200Electrical system
Technical data 374
Electronic Brake Booster (EBB) 84
Electronic Stability Program see ESP
Electronic Traction System (ETS) 83
Emergency call system 202
Emergency calls
Initiating an emergency call 205
With Tele Aid 204
Emergency operation (Limp Home
Mode) 156
Emergency operations
Closing tilt/sliding sunroof 330
Locking the vehicle 328
Opening tilt/sliding sunroof 330
Remote door unlock 209
Unlocking the tailgate 327
Unlocking the vehicle 327
Emergency tensioning device see ETD
Emission control 237
Emission control information label 368
Ending
A call (telephone) 147Engine
Compartment 242
Message in display 294
Starting with SmartKey 49
Technical data 370
Turning off with SmartKey 58
Engine air filter
Messages in display 310
Engine cleaning 285
Engine compartment 242
Hood 242
Engine malfunction indicator lamp 25,
294
Engine number 384
Engine oil 243, 377
Adding 247
Additives 378
Checking level 243
Consumption 243
Display messages 312
Messages in display 245, 311
Oil dipstick 247
Viscosity 384

398 Index
High beam flasher 52, 114
High beam headlamps
Messages in display 315
Replacing bulbs 336, 338
Switching on 114
High mounted brake lamp 336
Hood 242
Closing 243
Messages in display 313
Opening 242
Hydroplaning 224
I
Identification labels 368
Certification label 368
Vehicle identification number
(VIN) 368
Ignition
Switching on 49
Ignition (Position in starter switch) 35
Immobilizer 88
Activating 88
Deactivating 88
Infant and child restraint systems 72
Installing 76
LATCH child seat anchors 77Information
Button for Tele Aid 207
Inside rear view mirror
Auto-dimming 163
Installing
Cargo compartment cover 187
Infant and child restraint systems 76
Wiper blades 347
Instructions
Loading 192
Instrument cluster 24, 120, 385
Cleaning 287
Coolant temperature display 120
Illumination 120
Lamps in 296
Multifunction display 123
Outside temperature indicator 122
Selecting language 137
Instrument lighting 120
Instruments and controls see Cockpit
Interior lighting 116
Delayed shut-off 141
Manual operation 117
Interior rear view mirror
Adjusting 41
Intermittent wiping 54Interval wiping 55
Switching off 55
Switching on 55
J
Jack 324
Jump starting 356
K
Key, mechanical 327
Key, SmartKey
Battery check lamp 94
Checking the batteries 95
Factory setting 94
Global locking 94
Global unlocking 94
Loss of 96
Positions in starter switch 35
Remote controls 92
Restoring to factory setting 95
Selective setting 94
Starting the engine 49
Unlocking with 34
Key-dependency memory
Settings 144
Keys 92
Kickdown 385