418 Technical dataFuels, coolants, lubricants, etc.CapacitiesVehicle components and their respective
lubricants must match. Therefore use only
products tested and approved by
Mercedes-Benz.Please refer to the Factory Approved
Service Products pamphlet, or inquire at
your Mercedes-Benz Center.
Model
Capacity
Fuels, coolants, lubricants, etc.
Engine with oil filter
CL 500
CL 55 AMG
CL 600
CL 65 AMG
8.5 US qt (8.0 l)
8.0 US qt (7.5 l)
9.5 US qt (9.0 l)
11.0 US qt (10.5 l)
Approved engine oils
Automatic transmission
CL 500
CL 55 AMG
CL 600
CL 65 AMG
9.1 US qt (8.6 l)
9.1 US qt (8.6 l)
8.2 US qt (7.7 l)
8.2 US qt (7.7 l)
MB Automatic Transmission Fluid
Rear axle
CL 500
CL 55 AMG
CL 600
CL 65 AMG
1.7 US qt (1.6 l)
2.1 US qt (2.0 l)
2.1 US qt (2.0 l)
2.1 US qt (2.0 l)
Hypoid gear oil SAE 85 W 90
Hydraulic system for ABC
approx. 4.2 US qt (4.0 l)
MB Hydraulic Fluid
Power steering
approx. 1.1 US qt (1.0 l)
MB Power Steering Fluid
(Pentosin CHF 11S)
Front wheel hubs
approx. 3.5 oz (100 g) each
High temperature roller bearing grease
Brake system
0.7 US qt (0.7 l)
MB Brake Fluid (DOT 4+)
420 Technical dataFuels, coolants, lubricants, etc.Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System (U.S. vehicles) or FSS (Canada
vehicles). For a listing of approved engine
oils and oil filters, refer to the Factory
Approved Service Products pamphlet, or
contact an authorized Mercedes-Benz
Center.
Engine oil additives
Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from
blending oil additives are not covered by
the Mercedes-Benz Limited Warranty.Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil is used in the air condition-
ing system.
Never use R-12 (CFC) or mineral-based lu-
bricating oil. Otherwise damage to the
system will occur.
Brake fluid
During vehicle operation, the boiling point
of the brake fluid is continuously reduced
through the absorption of moisture from
the atmosphere.
Only brake fluid approved by
Mercedes-Benz is recommended. Your au-
thorized Mercedes-Benz Center will pro-
vide you with additional information.
!Using engine oils and oil filters of
specification other than those express-
ly required for the Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles), or changing of oil and oil filter at
change intervals longer than those
called for by the Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles) will result in engine damage not
covered by the Mercedes-Benz Limited
Warranty.
Please follow Maintenance System
(U.S. vehicles) or FSS (Canada vehi-
cles) recommendations for scheduled
oil changes. Failure to do so will result
in engine damage not covered by the
Mercedes-Benz Limited Warranty.
Warning!
G
Under extremely strenuous operating condi-
tions, this moisture content can lead to the
formation of bubbles in the system, thus re-
ducing the system’s efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s
Maintenance Booklet for replacement.
421 Technical data
Fuels, coolants, lubricants, etc.
Premium unleaded gasoline
Fuel requirements
Use only premium unleaded fuel:
The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research (R) octane num-
ber and the Motor (M) octane number:
(R+M)/2). This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not exceed
10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional cosolvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Whenever you are around gasoline,
avoid inhaling fumes and skin contact, extin-
guish all smoking materials. Never allow
sparks, flame or smoking materials near
gasoline!
!To maintain the engine’s durability and
performance, premium unleaded gaso-
line must be used. If premium unleaded
is not available and low octane fuel is
used, follow these precautions:
Have the fuel tank only partially
filled with unleaded regular and fill
up with premium unleaded as soon
as possible.
Avoid full throttle driving and abrupt
acceleration.
Do not exceed an engine speed of
3000 rpm if the vehicle is loaded
with a light load such as two per-
sons and no luggage.
Do not exceed
2/3 of maximum ac-
celerator pedal position if the vehi-
cle is fully loaded or operating in
mountainous terrain.
422 Technical dataFuels, coolants, lubricants, etc.Gasoline additives
A major concern among engine manufac-
turers is carbon build-up caused by gaso-
line. Mercedes-Benz recommends only the
use of quality gasoline containing additives
that prevent the build-up of carbon depos-
its.
After an extended period of using fuels
without such additives, carbon deposits
can build up especially on the intake valves
and in the combustion area, leading to en-
gine performance problems such as:
Warm-up hesitation
Unstable idle
Knocking/pinging
Misfire
Power lossIn areas where carbon deposits may be en-
countered due to lack of availability of gas-
olines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to Factory
Approved Service Products Pamphlet for a
listing of approved product(s). Follow di-
rections on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and
may be harmful to the engine operation.
Damage or malfunction resulting from
poor fuel quality or from blending addition-
al fuel additives other than those tested
and approved by us for use on
Mercedes-Benz vehicles listed in the
Factory Approved Service Products
Pamphlet are not covered by the
Mercedes-Benz Limited Warranty.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which pro-
vides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately –22°F (–30°C) and cor-
rosion protection.
If the antifreeze mixture is effective to
–22°F (–30°C), the boiling point of the
coolant in the pressurized cooling system
is reached at approximately 266°F
(130°C).
The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over pro-
tection. Refer to Maintenance Booklet for
replacement interval.
428 Technical termsCAN system
(C
ontroller A
rea N
etwork)
Data bus network serving to control ve-
hicle functions such as door locking or
windshield wiping.
Cockpit
All instruments, switches, buttons and
indicator/warning lamps in the passen-
ger compartment needed for vehicle
operation and monitoring.
Cold tire inflation pressure
(
page 309)
COMAND
(Cockpit M
anagement and D
ata
System)
Information and operating center for
vehicle sound and communications
systems, including the radio and navi-
gation system, as well as other optional
equipment (CD changer, telephone,
etc.).Control system
The control system is used to call up
vehicle information and to change
component settings. Information and
messages appear in the multifunction
display. The driver uses the buttons on
the multifunction steering wheel to
navigate through the system and to ad-
just settings.
Cruise control
Driving convenience system that auto-
matically maintains the vehicle speed
set by the driver.
Curb weight
(
page 309)
Distronic*
A driving convenience cruise control
system which helps the driver maintain
a pre-selected speed:
If there is no vehicle directly ahead,
the system operates in the same
way as conventional ->cruise con-
trol.
If a slower moving vehicle is ahead,
Distronic will reduce your vehicle
speed to the extent permitted by re-
duced throttle and up to 20% brak-
ing power to maintain the preset
minimum following distance.
DOT
(Department o
f Transportation)
(
page 309)
Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine pro-
duced.
Engine oil viscosity
Measurement for the inner friction (vis-
cosity) of the oil at different tempera-
tures. The higher the temperature an
oil can tolerate without becoming thin,
or the lower the temperature it can tol-
erate without becoming viscous, the
better the viscosity.
429 Technical terms
ESP
®(Electronic S
tability Pr
ogram)
Improves vehicle handling and direc-
tional stability.
ETD
(E
mergency T
ensioning D
evice)
Device which deploys in certain frontal
and rear collisions exceeding the sys-
tem’s threshold to tighten the seat
belts.
->SRS
FSS (Canada vehicles)
(F
lexible S
ervice S
ystem)
Maintenance service indicator in the
multifunction display that informs the
driver when the next vehicle mainte-
nance service is due. FSS evaluates en-
gine temperature, oil level, vehicle
speed, engine speed, distance driven
and the time elapsed since your last
maintenance service, and calls for the
next maintenance service accordingly.
GAWR
(G
ross A
xle W
eight R
ating)
(
page 309)Gear range
Number of gears which are available to
the automatic transmission for shifting.
The automatic gear shifting process
can be adapted to specific operating
conditions using the selector lever.
GPS
(G
lobal P
ositioning S
ystem)
Satellite-based system for relaying
geographic location information to and
from vehicles equipped with special re-
ceivers. Employs DVD digital maps for
navigation.
GVW
(G
ross V
ehicle W
eight)
(
page 309)
GVWR
(Gross V
ehicle W
eight R
ating)
(
page 310)
Instrument cluster
The displays and indicator/warning
lamps in the driver’s field of vision, in-
cluding the tachometer, speedometer,
engine temperature and fuel gauge.KEYLESS-GO*
System for entering and operating the
vehicle without the use of a SmartKey.
Kickdown
Depressing the accelerator past the
point of resistance shifts the transmis-
sion down to the lowest possible gear.
This very quickly accelerates the vehi-
cle and should not be used for normal
acceleration needs.
Kilopascal (kPa)
(
page 310)
Line of fall
The direct line that an object moves
downhill when influenced by the force
of gravity alone.
Locking knob
Knob on the door which indicates
whether the door is locked or un-
locked. Pushing the locking knob down
on an individual door from inside will
lock that door.
438 IndexEngine oil 274, 420
Adding 278
Additives 420
Changing 278, 420
Checking level 274
Consumption 274
Filler neck 278, 279
Messages in display 275, 276, 351
Recommended engine oils and oil
filter 420
Viscosity 428
ESP
®
82, 429
Messages in display 342
Warning lamp 332, 333
ETD 71, 429
Safety guidelines 66
Exterior rear view mirrors 43
Auto-dimming on the driver’s
side 178
Parking position 124, 180
Parking position for 164
Power folding 180
Storing parking position 124F
Filler neck, Engine oil 278, 279
First aid kit 369
Flat tire 386
Jacking up the vehicle 387
Lowering the vehicle 390
Mounting the spare wheel 386
Preparing the vehicle 386
Flexible Service System see FSS
Fluids
ABC fluid 279
Automatic transmission 279, 418
Brake fluid 272, 418, 420
Capacities 418
Engine coolant 280, 419, 422
Engine oil 418, 420
Hydraulic system for ABC 418
Power steering fluid 418
Windshield washer system and head-
lamp cleaning system 282, 419,
425
Fog lamps 128, 379
Messages in display 355, 357
Replacing bulbs 379, 383Front air bags 67
Front lamps see Headlamps
Front passenger front air bag 63, 67
Front passenger front air bag off indicator
lamp 74, 336
Front seat head restraints see Head re-
straints
FSS (Canada vehicles) 315, 429
Fuel 271, 419, 421
Additives 422
Capacities, Fuel tank 419
Consumption statistics after
start 151
Consumption statistics since last
reset 152
Filling the tank 270
Fuel filler flap and cap 270, 374
Fuel gauge 25, 331
Fuel reserve warning lamp 25, 331
Requirements, Octane rating 271,
419, 421
Technical data 419, 421
Fuel cap
Engine malfunction indicator
lamp 331
Message in display 360
443 Index
M
Maintenance 12, 315
Calling up service indicator 316
Clearing service indicator 316
FSS (Canada vehicles) 315, 429
Maintenance System (U.S.
vehicles) 430
Maintenance System
(U.S. vehicles) 315
Resetting service indicator 317
Service indicator 315
Service term exceeded 316
Maintenance System (U.S. vehicles) 430
Manual headlamp mode see Headlamps
Manual shift program CL 55 AMG and
CL 65 AMG
Automatic transmission 175
Massage function (PULSE, Multicontour
seats*) 118
Maximum load rating, Tires 310
Maximum loaded vehicle weight 310
Maximum tire inflation pressure 310
Mechanical key 372Loss of 94, 100
Memory function 430
Menus see Control system menus
Messages in display see Multifunction dis-
play messages
Microphone, Hands-free 29
Mirrors
Adjusting 43
Antiglare positions 178
Auto-dimming mirrors 178
Exterior rear view mirror, Storing park-
ing position 124
Exterior rear view mirrors 43, 178
Interior rear view mirror 43, 178
Power folding exterior rear view
mirrors 180
Vanity mirror in sun visor 181, 230
MON 271, 419, 430
Motor Octane Number see MON
MP3-CD operation
Selecting tracks 144
Multicontour seats* 117Multifunction display 137, 430
Changing settings see Control system
menus and Control system sub-
menus
Selecting language 158
Standard display 141
Multifunction display messages
ABC 339
ABS 341
Air filter 341
Battery 345
Brake fluid 346
Brake lamps 354
Brake pads 346
Coolant 347
Cruise control 350
Distronic* 342
Door 350
Engine oil 275, 351
ESP
®
342
Fog lamps 355, 357
Fuel cap 360
Headlamps 355