2006 MAZDA MODEL MX-5 MIATA change time

Black plate (241,1)
Flat Tire
Either run-flat tires or conventional tires
are equipped on your Mazda depending
on the specification, therefore the
procedure for repairing a flat tire differs
depending on the type of tire. Before
driving, make sure which type of tire is
equipped on your Mazda. If you cannot
identify your tire type, consult an
Authorized Mazda Dealer.
qHow to identify your tire type
Run-flat tire
A run-flat tire has a “RFT ”mark on the
side wall.
Conventional tire
A conventional tire does not have a
“ RFT ”mark on the side wall.
q Vehicle with run-flat tires
WARNING
Vehicle Handling When Flat Tire
Warning Light Illuminates:
When the flat tire warning light
illuminates or the tire pressure
warning beep sound is heard, it is
dangerous to drive the vehicle at high
speeds, or perform sudden
maneuvering or braking. Vehicle
drivability could worsen and result in
an accident.
When the flat tire warning light
illuminates or the tire pressure
warning beep sound is heard, decrease
vehicle speed immediately and avoid
sudden maneuvering and braking.
Have the tires checked or perform the
appropriate repair as soon as possible
by an Authorized Mazda Dealer.
If a run-flat tire is punctured, the FLAT
TIRE warning light illuminates in the
instrument cluster, and a beep sound is
heard for about 30 seconds.
NOTE
Until the flat tire is changed, the beep
sound is heard for about 30 seconds
every time the ignition switch is turned
to the ON position.
In Case of an Emergency
Flat Tire
7-3
MX-5_8U35-EA-05F_Edition4 Page241
Thursday, October 6 2005 11:4 AM
Form No.8U35-EA-05F

Black plate (288,1)
To change coolant
WARNING
Removing the Cooling System Cap:
Removing the cooling system cap
while the engine is running or hot is
dangerous. This might lead to cooling
system and engine damage and could
result in serious injury from escaping
hot coolant or steam. Turn off the
engine and wait until it's cool. Even
then, be very careful when removing
the cap. Wrap a thick cloth around the
cap and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you're sure all the pressure is
gone, press down on the cap―still
using a cloth ―turn the cap, and
remove it.
1. Make sure the engine is not running and it has cooled.
2. Remove the cooling system cap.
Tighten Tighten
Loosen Loosen
3. Remove the radiator drain plug and
drain the coolant into a suitable
container. Properly dispose of the used
coolant. 4. Flush out the system with running
water.
5. Drain the system completely. Insert and tighten the plug. Add as much
ethylene-glycol-based coolant mixture
and water (or undiluted FL22) as
necessary to provide freezing and
corrosion protection.
6. In extremely cold climates, add the mixture percentage recommended in
the coolant mixture percentage table.
7. Run the engine at idle with the cooling system cap off. Slowly add additional
coolant if necessary.
8. At this point, wait until the engine reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
9. Install the cooling system cap. Inspect all connections for leaks. Inspect the
level in the coolant reservoir one more
time and verify that the coolant level is
between the F and L marks.
8-20
Maintenance and Care
Owner Maintenance
MX-5_8U35-EA-05F_Edition4 Page288
Thursday, October 6 2005 11:5 AM
Form No.8U35-EA-05F

Black plate (291,1)
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
Use plain water if washer fluid is
unavailable.
But use only washer fluid in cold weather
to prevent it from freezing.
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
Maintenance and Care
Owner Maintenance
8-23
MX-5_8U35-EA-05F_Edition4 Page291
Thursday, October 6 2005 11:5 AM
Form No.8U35-EA-05F