2006 MAZDA MODEL MPV clock

Black plate (247,1)
WARNING
Incorrect Jacking Position:
Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even
kill someone. Use only the front and
rear jacking positions recommended
in this manual.
Improper Jack:
Using a jack that isn't designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone. Use only the jack
provided with your Mazda.
Placing Objects Under the Jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle. Never place objects
under the jack.
4. Insert the jack lever and attach the lug
wrench to tire jack.
5. Turn the lug wrench clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is firmly in position and that it
cannot slip or move.
6. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel.
In Case of an Emergency
Flat Tire
7-11
Mazda MPV_8U61-EA-05G_Edition1 Page247
Tuesday, June 21 2005 9:37 AM
Form No.8U61-EA-05G

Black plate (248,1)
qLocking Lug Nutsí
If your vehicle has optional antitheft
wheel lug nuts, one on each wheel will
lock the tires and you must use a special
key to unlock them. This key is attached
to the lug wrench and is stored with the
spare tire. Register them with the lock
manufacturer by filling out the card
provided in the glove box and mailing it
in the accompanying envelope. If you lose
this key, consult an Authorized Mazda
Dealer or use the lock manufacturer's
order form, which is with the registration
card.
Special key Antitheft lug nut
To remove an antitheft lug nut
1. Obtain the key for the antitheft lug nut.
2. Place the key on top of the nut, and be
sure to hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Don't use a
power impact wrench.
3. Place the lug wrench on top of the key
and apply pressure. Turn the wrench
counterclockwise.
To install the nut
1. Place the key on top of the nut, and be
sure to hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Don't use a
power impact wrench.
2. Place the lug wrench on top of the key,
apply pressure, and turn it clockwise.
qMounting the Spare Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
WARNING
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
7-12
In Case of an Emergency
íSome models.
Flat Tire
Mazda MPV_8U61-EA-05G_Edition1 Page248
Tuesday, June 21 2005 9:37 AM
Form No.8U61-EA-05G

Black plate (249,1)
2. Mount the spare tire.
3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
WARNING
Don't Apply Oil or Grease to Lug
Nuts, Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the tire
to come off, resulting in an accident.
In addition, lug nuts and bolts could
be damaged if tightened more than
necessary. Do not apply oil or grease
to lug nuts and bolts and do not
tighten the lug nuts beyond the
recommended tightening torque.4. Turn the lug wrench counterclockwise
and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you're unsure of how tight the nuts
should be, have them inspected at an
Authorized Mazda Dealer.
Nut tightening torque
N·m (kgf·m, ft·lbf)108―147
(11―15, 80―108)
In Case of an Emergency
Flat Tire
7-13
Mazda MPV_8U61-EA-05G_Edition1 Page249
Tuesday, June 21 2005 9:37 AM
Form No.8U61-EA-05G

Black plate (276,1)
To change coolant
WARNING
Removing the Cooling System Cap:
Removing the cooling system cap
while the engine is running or hot is
dangerous. This might lead to cooling
system and engine damage and could
result in serious injury from escaping
hot coolant or steam. Turn off the
engine and wait until it's cool. Even
then, be very careful when removing
the cap. Wrap a thick cloth around the
cap and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you're sure all the pressure is
gone, press down on the cap―still
using a cloth―turn the cap, and
remove it.
1. Make sure the engine is not running
and it has cooled.
2. Remove the cooling system cap.
F
L
Tighten Loosen
TightenLoosen
3. Remove the radiator drain plug and
drain the coolant into a suitable
container. Properly dispose of the used
coolant.4. Flush out the system with running
water.
5. Drain the system completely. Insert and
tighten the plug. Add as much
ethylene-glycol-based coolant mixture
and water (or undiluted FL22) as
necessary to provide freezing and
corrosion protection.
6. In extremely cold climates, add the
mixture percentage recommended in
the coolant mixture percentage table.
7. Run the engine at idle with the cooling
system cap off. Slowly add additional
coolant if necessary.
8. At this point, wait until the engine
reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
9. Install the cooling system cap. Inspect
all connections for leaks. Inspect the
level in the coolant reservoir one more
time and verify that the coolant level is
between the F and L marks.
qChanging Coolant (With Rear
Heater)
Have an Authorized Mazda Dealer change
the coolant according to the Scheduled
Maintenance (page 8-3).
8-16
Maintenance and Care
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page276
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (295,1)
NOTE
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
lWhen reinstalling the sealing cover,
make sure
faces up.
Replacing a fog light bulbí
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.
2. If a retaining spring is equipped, swing
it outward.
3. Disconnect the socket from the
electrical connector by pressing the tab
on the connector with your finger.
4. Turn the bulb counterclockwise and
remove it. Carefully remove the fog
light bulb from its socket by pulling it
straight back.
5. Install the new bulb in the reverse order
of removal.
Front turn signal lights/Front side-
marker lights
1. Turn the screw counterclockwise and
remove it.
2. Turn the center section of the plastic
retainer counterclockwise and remove
it, then partially peel back the
mudguard.
Removal
Installation
Maintenance and Care
Owner Maintenance
8-35íSome models. Mazda MPV_8U61-EA-05G_Edition1 Page295
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (296,1)
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse order
of removal.
Side turn signal lights
1. Slide the unit as shown in the figure to
remove it.
2. Detach the electrical connector from
the unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Parking lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Taillights/Rear-
side marker lights
1. Remove the bolts with a Phillips
screwdriver and remove the rear
combination component.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Taillights/Rear side-marker lights Reverse lights Rear turn signal lights Brake lights/Taillights
Pull outward
8-36
Maintenance and Care
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page296
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (297,1)
4. Install the new bulb in the reverse order
of removal.
High-mount brake lights
1. Remove the liftgate upper trim.
2. Push the tab as shown in the figure,
and then remove the high-mount brake
light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
NOTE
An unsecured high-mount brake light
will allow water to leak into the vehicle.
Make sure the high-mount brake light is
tightly fastened to the vehicle and if
water still leaks, consult an Authorized
Mazda Dealer.
License plate lights
1. Slide the unit as shown in the figure to
remove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
Maintenance and Care
Owner Maintenance
8-37
Mazda MPV_8U61-EA-05G_Edition1 Page297
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (360,1)
A
Accessory Socket .............................. 6-57
Add-On Non-Genuine Parts and
Accessories ....................................... 9-13
Air Bag Systems ............................... 2-56
Air Filter ............................................ 8-21
Antenna ............................................. 6-14
Anti-Lock Brake System (ABS) ......... 5-6
Warning light ............................... 5-6
Appearance Care ............................... 8-44
Ashtray .............................................. 6-49
Audio System ................................... 6-14
Audio control switch .................. 6-42
Operating tips for audio
system ........................................ 6-14
Safety certification ..................... 6-44
Automatic Transaxle
Driving tips ................................ 5-12
Fluid ........................................... 8-18
Overdrive ................................... 5-11
Shift-lock override ..................... 5-11
Shift-lock system ........................ 5-11
Transaxle ranges .......................... 5-9
B
Battery
Emergency starting .................... 7-18
Maintenance ............................... 8-26
Specifications ............................. 10-4
Beep Sounds
Ignition key reminder ................. 5-32
Lights-on reminder ..................... 5-32
Power sliding door beep ............. 5-32
Seat belt warning beep ............... 5-32
Before Starting the Engine .................. 4-6
After getting in ............................. 4-6
Before getting in .......................... 4-6
Body Lubrication .............................. 8-21
B
Bottle Holder ..................................... 6-53
Brake
Fluid ........................................... 8-17
Brakes
Anti-lock brake system (ABS) ..... 5-6
Foot brake .................................... 5-4
Pad wear indicator ........................ 5-7
Parking brake ............................... 5-4
Warning light ............................... 5-5
Break-In Period ................................... 4-7
Bulb Replacement ............................. 8-33
C
Capacities .......................................... 10-4
Carbon Monoxide ............................... 4-5
Cargo Securing Loops ...................... 6-56
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-14
Child Restraint
Child restraint precautions ......... 2-41
Installing child-restraint
systems ....................................... 2-45
LATCH child-restraint
systems ....................................... 2-53
Child Safety Locks for Rear Doors ... 3-12
Cigarette Lighter ............................... 6-49
Climate Control System ...................... 6-2
Gas specifications ...................... 10-5
Clock ................................................. 6-24
Courtesy Lights ................................. 6-48
Cruise Control ................................... 5-13
Cup Holder ........................................ 6-51
Customer Assistance ........................... 9-2
D
Dashboard Illumination .................... 5-23
11-2
Index
Mazda MPV_8U61-EA-05G_Edition1 Page360
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G