2006 MAZDA MODEL MPV light

Black plate (297,1)
4. Install the new bulb in the reverse order
of removal.
High-mount brake lights
1. Remove the liftgate upper trim.
2. Push the tab as shown in the figure,
and then remove the high-mount brake
light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
NOTE
An unsecured high-mount brake light
will allow water to leak into the vehicle.
Make sure the high-mount brake light is
tightly fastened to the vehicle and if
water still leaks, consult an Authorized
Mazda Dealer.
License plate lights
1. Slide the unit as shown in the figure to
remove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
Maintenance and Care
Owner Maintenance
8-37
Mazda MPV_8U61-EA-05G_Edition1 Page297
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (298,1)
Without moonroof, with overhead
console
Edge
Without either moonroof or overhead
console
Edge
With moonroof
Edge
3. Install the new bulb in the reverse order
of removal.
Overhead light, Courtesy lights, Vanity
mirror lightsí
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light
Edge
Courtesy lights
Edge
8-38
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page298
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (299,1)
Vanity mirror lights
Edge
3. Install the new bulb in the reverse order
of removal.
Luggage compartment light
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system doesn't work, first
inspect fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
Maintenance and Care
Owner Maintenance
8-39
Mazda MPV_8U61-EA-05G_Edition1 Page299
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (300,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
WARNING
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-41).
8-40
Maintenance and Care
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page300
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (301,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 DEFOG 40A Rear window defroster
2 BTN 60A STOP, HAZARD, ROOM, D.LOCK and DRL fuses
3 ABS 60A Antilock brake system
í, For protection of various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30A Rear heater
í, For protection of various circuits
8 IG KEY2 40A A/C, P.WINDí, MOONROOFíand R.WIP fuses
9 A/C 10A Air conditioner, For protection of various circuits
10 TAIL 15A Taillights
11 AC PWR 15A Inverter
12 HORN 15A Horn
13 FOG 15A For protection of various circuits
14 EEC 5A For protection of various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 HID L 20A―
Maintenance and Care
Owner Maintenance
8-41íSome models. Mazda MPV_8U61-EA-05G_Edition1 Page301
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (303,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
12 HAZARD 10A Hazard warning flashers
13 ROOM 15A Overhead lights, Map lights, Luggage compartment light
14 AUX POWER 25A Accessory socket
15 CLOSER LH 20A For protection of various circuits
16 AUDIO 10A Audio system, For protection of various circuits
17 D.LOCK 30A Power door locks
í, For protection of various circuits
18 P/SEAT 30A Power seatí
19 ENGINE 10A Engine control system
20 METER 10A Instrument cluster
21 STOP 15A Brake lights
22 CLOSER RH 20A For protection of various circuits
23 ACC.DELAY 30A Power windows delay, For protection of various circuits
24 METER 15A Instrument cluster, INH switch
25 ST.SIGN 10A Starter signal
26 CIGAR 25A Lighter
27―― ―
28―― ―
Maintenance and Care
Owner Maintenance
8-43íSome models. Mazda MPV_8U61-EA-05G_Edition1 Page303
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (307,1)
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don't allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Dry the brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn't need it.
qRepairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
CAUTION
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
qBright-Metal Maintenance
lUse tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
lTo prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
lDuring cold weather or in coastal areas,
cover bright-metal parts with a coating
of wax or preservative heavier than
usual. It would also help to coat them
with noncorrosive petroleum jelly or
some other protective compound.
Maintenance and Care
Appearance Care
8-47
Mazda MPV_8U61-EA-05G_Edition1 Page307
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (308,1)
CAUTION
Don't use steel wool, abrasive cleaners,
or strong detergents containing highly
alkaline or caustic agents on chrome-
plated or anodized aluminum parts.
This may result in damage to the
protective coating and cause
discoloration or paint deterioration.
qUnderbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also
to do this every month.
Pay special attention to these areas
because they easily hide mud and dirt.It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.
WARNING
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Dry the brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal.
qAluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
NOTE
lDon't use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
lOnly use a mild soap or neutral
detergent and always use a sponge or
soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean the
wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
lAvoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
lIf your aluminum wheels lose luster,
wax the wheels.
8-48
Maintenance and Care
Appearance Care
Mazda MPV_8U61-EA-05G_Edition1 Page308
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G