2006 LEXUS RX330 light

STARTING AND DRIVING
424
CAUTION
To avoid accidentally engaging the cruise control, turn
the system off when it is not in use. Make sure the
“CRUISE” indicator light is off.
(c) Setting the cruising speed
The transmission must be in the “D” position or the shift range
position must be “4” (fourth range) or “5” (fifth range) in “\
S”
mode (with multi−mode type) before you set the cruising
speed.

STARTING AND DRIVING
425
Bring your vehicle to the desired speed, push the lever down
in the “−
SET” direction and release it. This sets the vehicle at
that speed. At this time, the display indicates settings such as
the preset vehicle speed, whether a vehicle is present ahead
and the selected following distance. If no vehicle is detected
ahead, the display does not indicate the vehicle ahead. You
can now take your foot off the accelerator pedal.
If you need to accelerate — for example, when passing —
depress the accelerator pedal enough for the vehicle to exceed
the preset speed. When you release the accelerator pedal, the
vehicle will return to the control prior to acceleration.
You cannot set a desired speed if the master warning light
comes on, the alarm sounds and the display indicates one of
the warning codes “E1”, “E2” or “E3”. If any of the above codes
appears on the display, see “(l) Vehicle −to−vehicle distance
control mode failure warning” on page 431. (d) Cancelling the vehicletovehicle distance control
mode
The vehicle
−to−vehicle distance control mode may be
temporarily cancelled by the driver or by the system itself under
certain circumstances. Temporary cancellation allows the set
cruising speed and vehicle −to−vehicle distance to remain in
memory.
The vehicle −to−vehicle distance control mode can be
temporarily cancelled by doing the following:
 Pulling the lever in the “CANCEL” direction and releasing it
 Depressing the brake pedal
Under certain circumstances, the vehicle −to− vehicle distance
control mode is temporarily cancelled:
 When vehicle speed falls below 40 km/h (25 mph)
 When vehicle stability control is activated
The “READY” indicator light comes on to indicate that the
system is still in operation.
To turn the system off, press the “ON −OFF” button. Make sure
the “CRUISE” indicator light is off.
If one of the warning codes “E1”, “E2” or “E3” appears\
on the
display, the preset speed automatically cancels out. See “(l)
Vehicle −to−vehicle distance control mode failure warning” on
page 431.
If the vehicle− to−vehicle distance control mode automatically
cancels out other than for the above cases, have your vehicle
checked by your Lexus dealer at the earliest opportunity.

STARTING AND DRIVING
431
(l) Vehicletovehicle distance control mode failure
warning
1Warning code2 “CRUISE” indicator light
3Master warning light
If a system malfunction is detected when the
vehicle −to−vehicle distance control mode is on, the master
warning light comes on, a warning tone sounds and a warning
code appears on the display. Dynamic laser cruise control is
automatically cancelled.
If “E3” appears on the display, the “CRUISE” indicator light in
the instrument cluster also flashes. If “E1” appears on the display,
the system cannot easily
measure the vehicle −to−vehicle distance because of a dirty
laser radar sensor glass.
If this code appears, clean the sensor glass with a soft cloth
and try setting the preset speed again. If the dirt is removed
without cleaning, the system will automatically enter the ready
mode.
If the system does not enter the ready mode even after
cleaning or the code remains on the display, the system might
be malfunctioning. Although the vehicle may still be operated,
please contact your Lexus dealer.
CAUTION
Always keep the sensor glass clear and never allow it to
be covered with icicle or any substance, so it can detect
the vehicle in front.

STARTING AND DRIVING
432If “E2” appears on the display,
the system may be having
trouble measuring the vehicle −to− vehicle distance because of
any of the following:
 The wipers are operating at high or low speeds
 Direct sunlight from the front
 It is difficult to make a measurement because of bad
weather (such as rainy, foggy, or snowy weather)
 Driving in “SNOW” mode
In the following cases, dynamic laser cruise control switches
to the ready mode:
 The wipers are stopped or are switched to variable
intermittent operation.
 No direct sunlight from the front
In the above conditions, push the lever up in the “+ RES”
direction and release it. Dynamic laser cruise control will be
restored. If the setting operation cannot be performed or if the
same code still appears even after the weather clears, the
system might have malfunctioned. Although there is no
problem to continue driving, please contact your Lexus dealer. If “E3” appears on the display,
a system malfunction has
been detected.
If this warning code appears, stop your vehicle in a safe place,
turn the ignition off, and then restart it to reset the system. If
the same code appears again or if the cruise control cannot be
set, the system may be malfunctioning. Although there is no
problem to continue driving, please contact your Lexus dealer.

STARTING AND DRIVING
434(a) Turning the system on and off
To turn the conventional cruise control mode on, press the
“ON−OFF” button. The “CRUISE” and “READY” indicator
lights on the
instrument panel will come on. Push the lever in
the “MODE” direction for longer than 1 second to change to
conventional cruise control mode. The indicator on the
instrument panel is as shown. You can now set the cruising
speed. Pressing the “ON− OFF” button again turns the system
off.
When the system is turned off, cruising speed must be reset
when the conventional cruise control mode is turned on again.
However, once the vehicle −to−vehicle distance control mode
activates and is used, the system cannot be changed to the
conventional cruise control mode using the above operation.
To change the mode, you must turn this system off and then on
again. Next pu sh the lever in the “MODE” direction for longer
than about 1 second. To change to the vehicle
−to−vehicle distance control mode
from the conventional cruise control mode, push the lever in
the “MODE” direction for longer than about 1 second.
CAUTION
To avoid accidentally engaging the cruise control, turn
the system off when it is not in use. Make sure the
“CRUISE” indicator light is off.

STARTING AND DRIVING
435
(b) Setting the cruising speed
With automatic transmission (standard type) —
The transmission must be in “D” before you set the cruising
speed.
With automatic transmission (multi
−mode type) —
The transmission must be in “D”, “5” (fifth range) or “\
4” (fourth
range) before you set the cruising speed.
Bring your vehicle to the desired speed, push the lever down
in the “− SET” direction and release it. This sets the vehicle at
that speed and the display shows the preset speed. You can
now take your foot off the accelerator pedal.
If you need to accelerate — for example, when passing —
depress the accelerator pedal enough for the vehicle to exceed
the preset speed. When you release the accelerator pedal, the
vehicle will return to the speed set prior to acceleration. You cannot set a desired speed if the master warning light
comes on, the alarm sounds and the display indicates the
warning
code “E3”. If this code appears on the display, see “(g)
Conventional cruise control mode failure warning” on page
437.
(c) Cancelling the conventional cruise control mode
The conventional cruise control mode may be temporarily
cancelled by the driver or by the system itself under certain
circumstances. T emporary cancellation allows the set cruising
speed to remain in memory.
The conventional cruise control mode can be temporarily
cancelled by doing the following:
 Pulling the lever in the “CANCEL” direction and releasing it
 Depressing the brake pedal
Under certain circumstances, the conventional cruise control
mode is temporarily cancelled:
 When vehicle speed falls below 40 km (25 mph)
 When vehicle stability control is activated
When vehicle speed drops 16 km/h (10 mph) below the set
speed, the conventional cruise control mode is cancelled and
the set speed is erased from memory.
The “CRUISE” indicator light remains on to indicate that the
system is still in operation.

STARTING AND DRIVING
436To turn the system off, push the “ON
−OFF” button. Make sure
the “CRUISE” indicator light is off.
If the conventional cruise control mode automatically cancels
out other than for the above cases, have your vehicle checked
by your Lexus dealer at the earliest opportunity.
(d) Resuming the conventional cruise control mode
If the conventional cruise control mode is temporarily
cancelled, the cruising speed can be resumed by pushing the
lever up in the “+ RES” direction.
Vehicle speed must be above 40 km/h (25 mph).
(e) Resetting to a faster speed
Push the lever up in the “+ RES” direction and hold it. Release
the lever when the desired speed is attained. While the lever
is held up, the vehicle will gradually gain speed.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
increased 1.6 km/h (1 mph) each time by pushing the lever up
in the “+ RES” direction quickly within 0.6 seconds.
However, a faster way to reset is to accelerate the vehicle and
then push the lever down in the “ − SET” direction. (f) Resetting to a slower speed
Push the lever down in the “
− SET” direction and hold it.
Release the lever when the desired speed is attained. While
the lever is held down, the vehicle speed will gradually
decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pushing the lever down
in the “− SET” direction quickly within 0.6 seconds.
However, a faster way to reset is to accelerate the vehicle and
then push the lever down in the “ − SET” direction.
With automatic transmission (standard type) —
Even if you downshift from “D” to “4” in the conventional cruise
control mode, engine braking will not be enabled because this
mode is not cancelled. To decrease the vehicle’s speed, reset
to a slower speed with the cruise control lever or depress the
brake pedal. If you use the brake pedal, cruise control is
cancelled.
With automatic transmission (multi −mode type) —
Even if you downshift from “D” or “5” (fifth range) to “4” (fourth
range) in the conventional cruise control mode, engine braking
will not be enabled because this mode is not cancelled. To
decrease the vehicle’s speed, reset to a slower speed with the
cruise control lever or depress the brake pedal. If you use the
brake pedal, cruise control is cancelled.

STARTING AND DRIVING
437
(g) Conventional cruise control mode failure warning
If there is trouble in the conventional cruise control mode, the
“CRUISE” indicator light in the instrument cluster flashes, the
master warning light comes on and the alarm sounds, the
warning code “E3” will appear on the display.
If a system malfunction is detected when the conventional
cruise control mode is in the ready mode or operating, the
master warning light comes on, an alarm sounds and the
above code appears.
If this code appears, press the “ON
−OFF” button to turn the
system off and then push it again to turn it on. If the setting still
cannot be made or the same code appears again, the system
might have malfunctioned. Although there is no problem to
continue driving, please contact your Lexus dealer.
ELECTRONICALLY MODULATED AIR SUSPENSION
1Easy access mode switch
2Height control switch
3Height select switch