2006 LEXUS RX330 light

STEERING WHEEL AND MIRRORS
240
CAUTION
When doing the circling calibration, be sure to secure
a wide space, and watch out for people and vehicles
in the neighborhood. Do not violate any local traffic
rules while performing circling calibration.
 Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.
VANITY MIRRORS
To use the vanity mirror, swing the sun visor down and
open the cover.
The vanity light comes on when you open the cover.
To adjust the brightness of the vanity light, slide the knob.

AIR CONDITIONING
242
AUTOMATIC AIR CONDITIONING CONTROLS
You can adjust the brightness of the display. See “Multidisplay light control” on page 91 for details.

AIR CONDITIONING
245
(a) Climate control
SETTING OPERATION — automatic control
1. Push the “AUTO” button.
An indicator light will illuminate to show that the automatic
operation mode has been selected.
Air flow quantity, switching of the diffusers, on−off of the air
conditioning and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are automatically
adjusted. When you press the “AUTO” button with the air
intake mode at OUTSIDE AIR, internal circulation may be
applied for maximum cooling. The operation status is shown
by each indicator. When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the depressed button is set. Other conditions continue to be
adjusted automatically.
Push the “OFF” button to turn the air conditioning system off.

AIR CONDITIONING
248“DUAL” button —
This switch is used to set the temperatures independently for
the driver’s seat and front passenger seat.
Pushing the button changes the mode from independent and
linked.

Independent mode: Temperatures can be set
independently for the driver’s seat and front passenger’s
seat. The indicator light will illuminate to show that the
independent mode has been selected. The indicator light
will come on to show that the independent mode has been
selected.
 Linked mode: The same temperature is set for the driver’s
seat and front passenger’s seat. The indicator light will turn
off to show that the simultaneous temperature setting mode
has been selected.
When the temperature for the front passenger’s seat is
changed in linked mode, the mode is changed automatically to
independent mode.
INFORMATION
Knowledge for the twotemperature selector operation
This air conditioning system has two independent
temperature selectors: left and right (for the use of
driver and front passenger respectively).
 There are cases where the temperature of the airflow
may not accurately correlate on the driver and front
passenger side according to circumstances, even if
the left and right temperature selectors are set at the
same temperature. If this situation occurs, use the
fine tune operation to adjust the air temperature on
one side.
 There are cases where one or both of the airflow
temperatures may not accurately correlate with the
set temperature according to circumstances, when
the airflow temperature settings on the left and right
are substantially different. For example, if the left
controller is set at central or neutral temperature
while the right one is set at maximum heating or
maximum cooling, or vice versa. If this situation
occurs, use the fine tune operation to adjust the air
temperature on each side.

AIR CONDITIONING
251
If manual switching of air intake is desired —
The air intake control button is used to switch the air intake
between the OUTSIDE AIR mode and RECIRCULATED AIR
mode.
With the button in the OUTSIDE AIR mode, the indicator light
will turn off and the system will take fresh outside air into the
vehicle.
If quick circulation of cooled air is desired, push the air intake
control
button for RECIRCULATED AIR. The indicator light will
come on.
For normal use, it is best to keep the air intake control button
set to the OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily. To prevent fogging up of the windshield, the air intake mode
may change automatically to the OUTSIDE AIR mode
depending on the condition of the air conditioning system.
For example, when the ambient temperature is low, the air
intake mode may change automatically to the OUTSIDE AIR
mode. This is not a malfunction.
When the air conditioning is ON, if the engine coolant
temperature becomes extremely high, the RECIRCULATED
AIR mode is automatically selected. This is not a malfunction.
When
the engine coolant temperature is lowered, the previous
mode resumes.
If manual onoff of the air conditioning is desired —
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off.
The air conditioning does not work if the outside temperature
is lowered down to around 0 C (32F).
If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year− round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.

AUDIO
262
AUDIO SYSTEM (with singleCD player)
Quick reference for your audio system
You can adjust the brightness of the display. See “Instrument panel light control” on page 90 for details.

AUDIO
282
AUDIO SYSTEM (with sixCD changer)
Quick reference for your audio system
You can adjust the brightness of the display. See “Instrument panel light control” on page 90 for details.
If a Mark Levinson brand audio system is installed, the “Mark Levinso\
n” logo is shown on the panel.

AUDIO
298
NOTICE
Do not insert one CD stacked on top of another one or
feed them in continuously, to prevent CDs from getting
stuck in the player.
 Ejecting a single CD alone:
1. Push the “
” or “” button to display the CD number
you want to eject.
2. Push the “
” (eject) button for the CD briefly.
At this time, the display shows “EJECT” and the indicators at
both ends of the slot as well as CD number light up.
 Ejecting all the CDs:
Push the “
” (eject) button for the CD until you hear a
beep.