2006 LEXUS LX470 rear

OCCUPANT RESTRAINT SYSTEMS
169
16x610
CAUTION
Do not install a rearfacing child restraint system on
the third seat if it interferes with the lock mechanism
of the second seats. Otherwise, the child or second
seat occupant(s) may be killed or seriously injured in
case of sudden braking or a collision.
 Child restraint systems installed on the third seat
should not contact the second seat backs.
16X223a
1. Run the center lap belt through or around the convertible
seat following the instructions provided by its manufacturer
and insert the tab into the buckle taking care not to twist the lap
belt.
CAUTION
After inserting the tab, make sure the tab and buckle
are locked and that the lap belt is not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent you from properly latching the tab and
buckle.
 If the seat belt does not function normally, it cannot
protect your child from death or serious injury.
Contact your Lexus dealer immediately. Do not
install the child restraint system on the seat until the
seat belt is fixed.

OCCUPANT RESTRAINT SYSTEMS
171
16X226a
3. To remove the convertible seat, press the buckle release
button.
Installation with 3point type seat belt
(A) Infant seat installation
16X103b
An infant seat must be used in rearfacing position only.

OCCUPANT RESTRAINT SYSTEMS
172
16X070c
CAUTION
Never install a rearfacing child restraint system on
the front passenger seat even if the front passenger
occupant classification indicator light indicates
“OFF”. In the event of an accident, the force of the
rapid inflation of the front passenger airbag can
cause death or serious injury to the child if the
rearfacing child restraint system is installed on the
front passenger seat.
16x633
 If the driver’s seat position does not allow sufficient
space for safe installation, install the child restraint
system on the second right seat.
 Child restraint systems installed on the second seat
should not contact the front seat backs.

OCCUPANT RESTRAINT SYSTEMS
175
16X207
4. To remove the infant seat, press the buckle release button
and allow the belt to retract completely. The belt will move
freely again and be ready to work for an adult or older child
passenger.(B) Convertible seat installation
16X104b
A convertible seat must be used in forwardfacing or
rearfacing
position depending on the age and size of the
child. When installing, follow the manufacturer’s
instructions about the appropriate age and size of the
child as well as directions for installing the child restraint
system.

OCCUPANT RESTRAINT SYSTEMS
176Install the child restraint system on the front passenger seat
only when it is unavoidable. Your vehicle is equipped with a
front passenger occupant classification system. In order to
activate
the occupant classification system correctly, install the
forward−facing child restraint system on the front passenger
seat in the following order:
1. Turn the ignition key to the “ON” position.
2. Move the front passenger seat to the rearward position.
3. Put the child restraint system on the front passenger seat
without putting your weight on the front passenger seat.
4. Insert the seat belt tab into the seat belt buckle.
5. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retrac ted even slightly, it cannot be
extended. To hold the seat securely, make sure the belt is in the
lock mode before letting the belt retract.
6. While pressing the convertible seat firmly against the seat
cushion and seatback, let the shoulder belt retract as far as it
will go to hold the convertible seat securely.
CAUTION
Push and pull the child r estraint system in different
directions to be sure it is secure. Follow all the
installation instructions pr ovided by its manufacturer.
7. Put a child on the child restraint system and secure the child,
complying with the instructions provided by the child restraint
system manufacturer. The occupant classification indicator light should indicate
“OFF”
when the ignition key is in the “ON” position and the child
is in the child restraint system after following these procedures.
The “OFF” indicator indicates the SRS front passenger airbag
will not deploy. If the indicator light indicates “ON”, remove the
child restraint system and reinstall it with the ignition key in the
“ACC” or “LOCK” position. If the indicator light still indicates
“ON” when the ignition key is turned to the “ON” position, then
the SRS front passenger airbag may deploy in an accident. Do
not drive the vehicle in this condition. Remove the child
restraint system and contact your Lexus dealer.
CAUTION
Never install a rearfacing child restraint system on
the front passenger seat. A forwardfacing child
restraint system should only be installed on the front
passenger seat when unavoidable. If you must install
the child restraint system on the front passenger
seat, put the seat in its mo st rearward position, and
install the forwardfacing child restraint system in
the proper order. Otherw ise, the front passenger
occupant classification system cannot detect the
presence of the child rest raint system and the front
passenger airbag could deploy.

OCCUPANT RESTRAINT SYSTEMS
177
16X071b
CAUTION
Never install a rearfacing child restraint system on
the front passenger seat even if the front passenger
occupant classification indicator light indicates
“OFF”. In the event of an accident, the force of the
rapid inflation of the front passenger airbag can
cause death or serious injury to the child if the
rearfacing child restraint system is installed on the
front passenger seat.
16X111b
 Move seat fully back
 A forwardfacing child restraint system should be
allowed to be installed on the front passenger seat
only when it is unavoidable. Always move the seat
as far back as possible even if the front passenger
occupant classification indicator light indicates
“OFF”, because the front passenger airbag could
inflate with considerable speed and force. Otherwise,
the child may be killed or seriously injured.
 Do not allow the child to lean his/her head or any part
of his/her body against the door or the area of the
seat, front or rear pillar or roof side rail from which the
side airbags or curtain shield airbags deploy even if
the child is seated in the child restraint system. It is
dangerous if the side airbag and curtain shield airbag
inflate, and the impact could cause death or serious
injury to the child.

OCCUPANT RESTRAINT SYSTEMS
182
Do not allow the child to lean his/her head or any part
of his/her body against the door or the area of the
seat, front or rear pillar or roof side rail from which the
side airbags or curtain shield airbags deploy even if
the child is seated in a child restraint system. It is
dangerous if the side airbag and curtain shield airbag
inflate, and the impact could cause death or serious
injury to the child.
16X118d
1. Sit the child on a booster seat. Run the lap and shoulder belt
through or around the booster seat and across the child
following the instructions provided by its manufacturer and
insert the tab into the buckle taking care not to twist the belt.
Make sure the shoulder belt is correctly across the child’s
shoulder and that the lap belt is positioned as low as possible
on the child’s hips. See “Seat belts” on page 121 for details.
CAUTION
 Always make sure the shoulder belt is positioned
across the center of child’ s shoulder. The belt should
be kept away from child’s neck, but not falling off
child’s shoulder. Otherwise, the child may be killed
or seriously injured in case of sudden braking or a
collision.

OCCUPANT RESTRAINT SYSTEMS
189
DRIVING POSITION MEMORYSYSTEM
A microcomputer will memorize the position of the driver’s
seat, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position
profiles can be entered into the computer’s memory.
Recording the driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the selector lever is in the “P” position.
Setting the driving position
16X162
1. Adjust the driver’s seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps. The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps
and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
16X163
When you push button “1” or “2”, the driving position will
be automatically adjusted to the position recorded for that
button.