2006 LEXUS LX470 engine oil

ENGINE
411
62X002c
If the oil level is below or only slightly above the low line,
add engine oil of the same type as already in the engine.
Remove the oil filler cap and add engine oil a little at a time,
checking the dipstick. We recommend that you use a funnel
when adding oil. The approximate quantity of oil needed to
raise the level between low and full on the dipstick is indicated
as follows.
1.5 L (1.6 qt., 1.3 lmp. qt.)
For the engine oil capacity, see “Specifications” on page 402.
When the level reaches within the correct range, return the
filler cap and turn the cap clockwise until you hear a click.
NOTICE
 Be careful not to spill engine oil on the vehicle
components.
 Avoid overfilling, or the engine could be damaged.
 Check the oil level on the dipstick once again after
adding the oil.

ENGINE
412
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Lexus vehicle. Use
Lexus approved “Toyota Genuine Motor Oil” or equivalent to
satisfy the following grade and viscosity.
Oil grade: ILSAC multigrade engine oil.
Recommended viscosity: SAE 5W− 30
62sa08
Outside temperature
SAE 5W30 is the best choice, for good fuel economy, and
good starting in cold weather.
If SAE 5W30 oil is not available, SAE 10W30 oil may be
used. However, it should be replaced with SAE 5W30 at
the next oil change.
Oil identification mark
g62035
The ILSAC (International Lubricant Standardization and
Approval Committee) Certification Mark is added to some oil
containers to help you select the oil you should use.
To ensure excellent lubrication performance for your engine,
“Toyota Genuine Motor Oil” is available, which has been
specifically tested and approved for all Lexus engines.
Please contact your Lexus deal er for further details about
“Toyota Genuine Motor Oil”.

CHASSIS
418
SPECIFICATIONS
– DIFFERENTIALOil capacity Front
Rear
1.6 L (1.7 qt., 1.4 lmp.qt.)
3.3 L (3.5 qt., 2.9 lmp.qt.)
Oil typeHypoid gear oil API GL −5
Oil viscosityAbove − 18C (0F): SAE 90
Below − 18C (0F): SAE 80W or SAE 80W− 90
– TRANSFER
Oil capacity
1.3 L (1.4 qt., 1.1 lmp.qt.)
Oil typeGear oil API GL −4 or GL− 5
Recommended oil viscositySAE 75W− 90
– BRAKES
Pedal clearance
116 mm (4.57 in.) Min. *1
Pedal free play1 − 6 mm (0.04 − 0.24 in.)
Brake pad wear limit1.0 mm (0.04 in.)
Parking brake lining wear limit1.0 mm (0.04 in.)
Parking brake adjustment4 − 6 clicks *2
Fluid typeSAE J1703 or FMVSS No. 116 DOT 3
*1: Minimum pedal clearance when depressed with the force of 490 N (50 kgf,\
110 lbf.) with the engine running
*
2: Parking brake adjustment when pulled with the force of 196 N (20 kgf, 4\
4 lbf.)

CHASSIS
424
NOTICE
Only use the Suspension fluid AHC for the active height
control suspension. If you fill other fluids such as brake
fluid, power steering fluid, engine oil, etc., the active
height control suspension could be damaged.
CHECKING TIRE INFLATION PRESSURE
63x600b
 Type A

CHASSIS
433
Glossary of tire terminology
Tire related termMeaning
Cold tire inflation
pressuretire inflation pressure when the vehicle has been parked for at least 3 \
hours or
more, or it has not been driven more than 1.5 km or 1 mile under that co\
ndition
Maximum inflation
pressurethe maximum cold inflation pressure to which a tire may be inflated and \
it is shown
on the sidewall of the tire
Recommended inflation
pressurecold tire inflation pressure recommended by a manufacturer
Accessory weight
the combined weight (in excess of those standard items which may be rep\
laced) of
automatic transmission, power steering, power brakes, power windows, pow\
er
seats, radio, and heater, to the extent that these items are available as
factory−installed equipment (whether installed or not)
Curb weight
the weight of a motor vehicle with standard equipment including the maxi\
mum
capacity of fuel, oil, and coolant, and, if so equipped, air conditionin\
g and
additional weight optional engine
Maximum loaded vehicle
weight
the sum of —
(a) curb weight;
(b) accessory weight;
(c) vehicle capacity weight; and
(d) production options weight