2006 Lexus GX470 start stop button

KEYS AND DOORS
17
Operating the windows and moon roof
The windows and moon roof can be opened using a
wireless key from outside the vehicle.*NOTE:
* The windows and moon roof can be set inoperative.
Ask your Lexus dealer for details.
Push the “UNLOCK” button until the windows and moon roof
start to move. A beep sounds just before opening. When you
release the button, the windows and moon roof stop opening. For vehicles sold in U.S.A.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
NOTICE:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.
 Increase the separation between the equipment
and receiver.

OCCUPANT RESTRAINT SYSTEMS
199
Conditions for memorized position activation

Ignition key “ON” and selector lever in “P” position.
All parts of the memorized positions can be activated.
 Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of the
memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1” or “2”)\
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.

AUDIO
242
Cassette tape player operation
(a) Playing a cassette tape
When you insert a cassette tape, the exposed tape should
face to the right.
The player will automatically start when you insert a cassette
tape. At this time, “TAPE” appears on the display.
To stop or eject the cassette tape, push the “EJECT” button.
Autoreverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.
If a cassette is already in the slot, push the “TAPE” button.
Dolby Noise Reduction* feature: If you are listening to a
tape that was recorded with Dolby  Noise Reduction, push the
“
” button. The display will indicate that the Dolby noise
reduction system is on.
The Dolby NR mode reduces tape noise by about 10 dB. For
best sound reproduction, play your tapes with the Dolby NR on
or off according to the mode used for recording the tape.
To play a tape recorded without Dolby NR, push the button
again to turn off the Dolby NR.
* Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation. “DOLBY” and the double −D
symbol
are trademarks of Dolby Laboratories Licensing
Corporation.

AUDIO
264
Cassette tape player operation
(a) Playing a cassette tape
Push the “ON/SOURCE” button to choose tape mode.
The player will automatically start. At this time, “TAPE”
appears on the display.
You can play a cassette tape when a cassette tape is loaded
in the front audio system.
Autoreverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.(b) Manual program selection
“Program” button: Push the “” or “” (DISC/CH/PROG)
button to select the other side of a cassette tape. The display
indicates which side is currently selected. (“
” indicates the
top side, “” indicates the bottom side.)
“Rewind” button: Push and hold the “
” (TUNE/TRACK)
button until “REW” appears on the display.
To stop rewinding, push the same button.
“Fast forward” button: Push and hold the “
”
(TUNE/TRACK) button until “FF” will appears on the display.
To stop fast forwarding, push the same button.

STARTING AND DRIVING
355
(f) Good driving practice
If the transmission repeatedly shifts up and down between
the fourth and overdrive gears when climbing a gentle slope,
shift the selector lever to the “4” position. Be sure to shift the
selector lever to the “D” position after climbing the slope.
 When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Always use the brake pedal or parking brake to hold the
vehicle on an upgrade. Do not attempt to hold the
vehicle using the accelerator pedal, as this can cause
the transmission to overheat.
(g) If you cannot shift the selector lever
If you cannot shift the selector lever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see “If you cannot shift automatic transmission
selector lever” on page 453.
(h) Driving in second start mode
In the second start mode, the transmission system shifts up
from second gear. Use this mode when starting your vehicle
in sand, mud, ice or snow.
To set the second start mode, push the “2nd STRT” switch. In
the second start mode, the “2nd STRT” indicator light comes
on. To cancel the second start mode, push the “2nd STRT”
switch once again.

IN CASE OF AN EMERGENCY
462
Advisor record
 1
PTT (Push To Talk) button 2
Volume button
3
Phone button 4
“SERVICES” button
During a service call, you can record a conversation with the
Lexus Link Call Center Advisor. This function is very
convenient for drivers so they do not have to take notes while
driving.
To record: Push “SERVICES” button to record a conversation
with Lexus Link Call Center. At this time, you will hear beeps.
To stop recording, push the button again. Up to about 2
minutes of recording time is available.
When you push the “SERVICES” button, all previous
messages are deleted and the system begins recording your
new message. To playback:
Push the PTT or phone button and “Lexus Link
ready” will be announced. Then say “Advisor playback” to play
the recorded conversation. To stop the playback, push the
phone button. To restart the playback, say “Advisor playback”
and then “Resume” for resuming or “Play” for starting from t\
he
beginning.
To change the volume: Push “− VOL +” button on either side
to adjust the volume. When you change the volume, one beep
sounds.

IN CASE OF AN EMERGENCY
464
Voice Recognition
You can start voice recognition by pressing the phone or
PTT button. Although either button works the same way,
use the PTT button during a call.
Pressing the phone button during a call will terminate the call.
Some English audible voice prompts can be changed to
Spanish. For details, see “Audible voice prompts” on page
478.
ADVISOR PLAYBACK
Your Lexus Link system is equipped with an advisor playback
recorder to store information given to you during a call with a
Lexus Link Advisor. You can play back the stored audio
information at a later time, when you are no longer connected
to Lexus Link.
To record a conversation only during a call with Lexus
Link Call Center:
1. Press the “SERVICES” button.
You will hear beeps and recording starts. Note that start of
recording may be delayed up to five seconds to clear existing
audio information. Recording starts immediately after the last
beep.
2. Press the “SERVICES” button again.
Recording ends. To play back (only when the Lexus Link System is not in
a call):
1. Press the phone button.
You will hear “Lexus Link ready”.
2. Say “Advisor playback” .
The playback will start.
To stop the playback (partially through):
1. Press the phone* button.
The system will terminate the playback and return to audio
system control.
*: The PTT button cannot be used instead of the phone button.
To resume the playback:
1. Press the phone button.
You will hear “Lexus Link ready”.
2. Say “Advisor playback” .
You will hear “Play or resume?”.
3. Say “Play” or “Resume”.
If you say “Play”, the playback will start from the beginning. If\
you say “Resume”, the playback will start from where it had
been previously stopped.