2006 Lexus GS430 display

INTERIOR EQUIPMENT
106
OUTSIDE TEMPERATURE DISPLAY
G14036
On the instrument panel
This display shows the outside temperature when the
engine switch is on.
The displayed temperature ranges from – 40 C (– 40F) up to
50 C (122F). If the temperature does not appear on the
display or it shows “ − − −”, take your vehicle to your Lexus
dealer.
When the headlight switch is turned to the first or second click
stop, the brightness of the display will be reduced.
You can brighten the display. To adjust the brightness, see
“Instrument panel light control” on page 96.
G14037
 Multiinformation display
When you push the “DISP” switch with the engine switch on,
another outside temperature display appears on the
multi−information display.
The displayed temperature ranges from – 40 C (– 40F) up to
50 C (122F). If the temperature does not appear on the
display or it shows “E” or “− − ”, take your vehicle to your Lexus
dealer.
When the headlight switch is turned to the first or second click
stop, the brightness of the display will be reduced.
You can adjust the brightness of the display. To adjust the
brightness, see “Instrument panel light control” on page 96.

STEERING WHEEL AND MIRRORS
210When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the
driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.
G17008
To ensure correct functioning of antiglare mirror sensors
located on both sides of the mirror, do not touch or cover
the sensors with your finger or a piece of cloth, etc.
Compass
G17009
The compass indicates the direction in which the vehicle
is heading. The illustration shown above indicates the
vehicle is heading north.
Displays
Directions
N
NE E
SE S
SW W
NWNorth
Northeast East
Southeast South
Southwest West
Northwest

STEERING WHEEL AND MIRRORS
211
Pushing the “AUTO” button for longer than 3 seconds
turns on or off the compass display.
The compass may not show the correct direction in the
following conditions:

The vehicle is stopped immediately after turning.
The compass does not adjust while the vehicle is stopped.
 The engine switch is turned off immediately after turning.
 The vehicle is on an inclined surface.
 The vehicle is in a place where the earth’s magnetic field is
subject to interference by artificial magnetic fields
(underground parking, under a steel tower, between
buildings, roof parking, near a crossing, near a large
vehicle, etc.).
 The vehicle is magnetized. (There is a magnet or a metal
object near the inside rear view mirror.)
 The battery has been disconnected.
 Any door is open.
If the deviation is small, the compass works to calibrate the
direction automatically while the vehicle is in motion.
For obtaining additional precision or for complete calibrating,
see “CALIBRATING THE COMPASS” below.
NOTICE
Do not put magnets or a metal object near the inside rear
view mirror. Doing this may cause malfunction of the
compass sensor.
CALIBRATING THE COMPASS (deviation calibration)
The direction display on the compass deviates from the true
direction determined by the earth’s magnetic field. The
amount of deviation varies according to the geographic
position of the vehicle.
To adjust for this deviation, stop the vehicle and push the
“AUTO” button for longer than about 6 seconds until the zone
number (1 −15) appears on the display. Then push the button
again, referring to the following map to select the number of the
zone where the vehicle is.

STEERING WHEEL AND MIRRORS
212
G17016
Zone number
If the direction is displayed several seconds after adjustment,
the calibration is finished.
CAUTION
Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.
CALIBRATING THE COMPASS (circling calibration)
G17011
“CAL” appears on the display in case the circling calibration is
required due to a drastic change in the magnetic field. To
rectify this, follow the calibration procedure below.

STEERING WHEEL AND MIRRORS
213
G17012
Drive the vehicle slowly (at 8 km/h (5 mph) or lower) in a circle
until the direction is displayed. If there is not enough space to
drive in a circle, drive around the block until the direction is
displayed.
After driving in 1 to 3 circles in the above method, calibration
is complete with the “CAL” off the display and the direction
shown on the display.
If calibration cannot be performed because of the vehicle is
magnetized, take your vehicle to a Lexus dealer.
 Do not perform circling calibration of the compass in a place
where the earth’s magnetic field is subject to interference by
artificial magnetic fields (underground parking, under a
steel tower, between buildings, roof parking, near a
crossing, near a large vehicle, etc.).
 During calibration, do not operate electric systems (moon
roof, power windows, etc.) as they may interfere with the
calibration.
CAUTION
When doing the circling calibration, be sure to secure
a wide space, and watch out for people and vehicles
in the neighborhood. Do not violate any local traffic
rules while performing circling calibration.
 Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.

G18042
Vehicles with Navigation system
G18043
Vehicles without Navigation system
TOUCH SCREEN
216
OVERVIEW
1 Touch screen
2 “CLIMATE” button
The air conditioning operation screen is
shown.
(See page 254 for details.)
3 “AUDIO” button
The audio operation screen is shown.
(See page 274 for details.)
4 “INFO”button
The information menu screen is shown.
(See page 218 for details.)
5 “DISP” button
The display adjustment screen is
shown.
(See page 251 for details.)

TOUCH SCREEN
217
Initial screen
G18001
When you select the engine switch in “ACC” or “IG −ON” mode,
the initial screen appears and the system begins operating.
After a few seconds, the initial screen disappears.
CAUTION
When the vehicle is stopped with the engine running,
always apply the parking brake for safety.
Touch switch operation
This system is operated mainly by the switches on the screen.
To prevent damage to the screen, lightly touch switches on the
screen with your finger. When you touch a switch on the
screen, a beep sounds.
Do not use objects other than your finger to touch the screen.
INFORMATION
 If the system does not respond to a touch of a switch,
move your finger away from the screen and then
touch it again.
 You cannot operate dimmed switches.
 Wipe off fingerprints on the surface of the display
using a glass cleaning cloth.
 The displayed image may become darker and moving
images may be slightly distorted when the display is
cold.

TOUCH SCREEN
218
INFORMATION MENU
G18044
Vehicles with Navigation system*
G18045
Vehicles without Navigation system
*For other functions such as Maintenance and Calender, see
“Navigation System Owner’s Manual”. For “Lexus park Assist”, see “Setting the park assist system”\
on page 385. For “Adjust clock”, see “Clock” on page 103.
Trip information
Trip information such as driving time, driving distance,
average vehicle speed, fuel consumption, etc. can be
displayed on the screen.
1. Push the
“INFO” button to display the Information
Menu screen.
G18045
2. Touch the “Trip Info.” switch.