2006 Lexus GS430 clock

EXTERIOR EQUIPMENT
127
Using a mechanical key
G15004
To unlock the trunk lid, insert the mechanical key and turn
it clockwise.
To close the trunk lid, lower it and press down on it. After
closing the trunk lid, try pulling it up to make sure it is securely
closed.
CAUTION
 Keep the trunk lid closed while driving. This not only
keeps the luggage from being thrown out, but also
prevents exhaust gases from entering the vehicle.
 Always lock the trunk lid and all doors, and keep
away the vehicle keys out of children’s reach.
 Never leave children unattended in the vehicle. Un
supervised children may lock themselves in the
vehicles or trunk and suffer serious injuries or death.
Trunk lid closer
If the trunk lid is closed but does not latch shut, it
automatically closes completely.
CAUTION
Pay careful attention not to get your fingers trapped
as the trunk lid automatically closes when the trunk
has not been fully closed.
 Never allow a child to operate the trunk lid.
NOTICE
Do not apply excessive force when the trunk lid closer
is operating. Doing so may damage the trunk lid closer.
Also, be careful not to leave the key inside the trunk.

EXTERIOR EQUIPMENT
130
G15016
2. To remove the fuel tank cap, turn the cap slowly
counterclockwise by 90 degrees (to the pressure point
1, then turn it additional 30 degrees (to point 2).
Pause slightly before removing it.
It is not unusual to hear a slight swoosh when the cap is
opened.
G15015
3. The removed cap can be stored on the back side of the
fuel filler door.
Position the cap so that the hooks point to the left and right, and
set it in the receptacle on the back side of the door.
When installing the cap, turn the cap clockwise until you
hear a click. When you hear the click, the cap is fully
closed.
If the cap is not installed securely, the malfunction indicator
lamp comes on. Make sure the cap is tightened securely.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible.

TOUCH SCREEN
218
INFORMATION MENU
G18044
Vehicles with Navigation system*
G18045
Vehicles without Navigation system
*For other functions such as Maintenance and Calender, see
“Navigation System Owner’s Manual”. For “Lexus park Assist”, see “Setting the park assist system”\
on page 385. For “Adjust clock”, see “Clock” on page 103.
Trip information
Trip information such as driving time, driving distance,
average vehicle speed, fuel consumption, etc. can be
displayed on the screen.
1. Push the
“INFO” button to display the Information
Menu screen.
G18045
2. Touch the “Trip Info.” switch.

STARTING AND DRIVING
371
(B) Collision will be avoided by changing the steering
G31056
 3
About 50 cm (1.5 ft.) to about 100 cm (3.0 ft.)
4About 37.5 cm (1.1 ft.) to about 50 cm (1.5 ft.)
5About 25 cm (0.8 ft.) to about 37.5 cm (1.1 ft.)
The steering guide symbol and the arrow indicating which
direction should be steered appear along with the bar
indicators and beeps. The above illustration indicates that the collision will be
avoided by turning the steering wheel clockwise.
When
the possibility that the distance between the vehicle and
the obstacle is less than about 25 cm (0.8 ft.) is eliminated by
turning the steering wheel more, the steering guide symbol will
go out and the beeps will stop sounding.
The steering guide symbol and arrow are not instructions
you must observe. They are just a guide to avoid a
collision.
1 Multiinformation display:
The indicator bars will come on depending on the
distance to the obstacle . The steering guide symbol and
arrow will also come on.
2Screen:
The indicator bars will come on in yellow depending on
the distance to the obstacle. The steering guide symbol
and arrow will also come on. In addition, the current
direction of the tires is also indicated in 3 stages.
Beeps:
As distance to the obstacle gets closer, the interval of the
intermittent sound gets shorter, and then finally to a continuous
sound when the distance between the vehicle and the obstacle
is less than about 25 cm (0.8 ft.).

IN CASE OF AN EMERGENCY
476
G40007
4. Block the wheel diagonally opposite the flat tire to
keep the vehicle from rolling when it is jacked up.
When blocking the wheel, place a wheel block in front of
one of the front wheels or behind one of the rear wheels.
G40008
5. Loosen all the wheel nuts.
Always loosen the wheel nuts before raising the vehicle.
Turn the wheel nuts counterclockwise to loosen them.
To get maximum leverage, fit the wrench to the nut so
that the handle is on the right side, as shown above.
Grab the wrench near the end of the handle and pull up
on the handle. Be careful that the wrench does not slip
off the nut.
Do not remove the nuts yet − just unscrew them about
one−half turn.
CAUTION
Never use oil or grease on the bolts or nuts. The
nuts may loosen and the wheels may fall off, which
could cause a serious accident.

IN CASE OF AN EMERGENCY
477
G40009
6. Position the jack at the jack points as shown.
Make sure the jack is positioned on a level and solid
surface.
G40010
7. After making sure no one is in the vehicle, raise it
high enough so that the spare tire can be installed.
Allow for the fact that you need more ground clearance
when putting on the spare tire than when removing the
flat tire.
To raise the vehicle, insert the jack handle into the jack
(it is a loose fit) and turn it clockwise. As the jack touches
the vehicle and begins to lift, double −check that it is
properly positioned.
CAUTION
Never get under the vehicle when the vehicle is
supported by the jack alone.

IN CASE OF AN EMERGENCY
479
G40013
9. Reinstall all the wheel nuts finger tight.
Align the holes in the wheel with the bolts. Then lift up
the wheel and get at least the top bolt started through its
hole. Wiggle the tire and press it back over the other
bolts.
Reinstall the wheel nuts and tighten them as much as
you can by hand. Press the tire back and see if you can
tighten them more.
CAUTION
Never use oil or grease on the bolts or nuts. Doing
so may lead to overtightening the nuts and
damaging the bolts. The nuts may loosen and the
wheels may fall off, which could cause a serious
accident. If there is oil or grease on any bolt or nut,
clean it.
G40014
10. Lower the vehicle completely and tighten the
wheel nuts.
Turn the jack handle counterclockwise to lower the
vehicle.
Use only the wheel nut wrench to tighten the nuts. Do
not use other tools or any additional leverage other than
your hands, such as a hammer, pipe or your foot. Make
sure the wrench is securely engaged over the nut.
Tighten each nut a little at a time in the order shown.
Repeat the process until all the nuts are tight.

IN CASE OF AN EMERGENCY
488Tips for towing a stuck vehicle:
The following methods are effective to use when your
vehicle is stuck in the mud, sand or other condition from
which the vehicle cannot be driven out under its own
power. Use extreme caution when towing the vehicle. In
addition, keep away from the vehicles and towing cable or
chain when towing.

Remove the sand and soil in the front and the back of the
tires.
 Place stones or wood under the tires.
(e) Installing towing eyelet
G40020
1. Remove the front towing eyelet cover on the front bumper
by using a flathead screwdriver. To protect the bodywork,
place a piece of rag over the cover.
G40021
2. Use the towing eyelet in the trunk. Secure it to the hole on
the bumper by turning clockwise. (For the eyelet location, see
page 474.)