2006 Lexus GS300 warning

Dynamic Radar Cruise Control Operation
The millimeter wave radar sensor in this system primarily detects the reflected wave from the rear end of the vehicle ahead of you to determine
the presence of the vehicle ahead as well as measuring the vehicle−to−vehicle distance. The detection range of the sensor is about 120 m
(400 ft.) ahead.
If no vehicle is detected ahead of you:
Your cruising speed is maintained at the preset speed from about 45 km/h (28 mph) to about 135 km/h (85 mph).
If a vehicle is detected ahead of you:
Your cruising speed changes in proportion to the speed of the vehicle ahead to maintain an appropriate distance from your vehicle to
the vehicle ahead.
If the vehicle ahead is out of the detection range, your cruising speed will be gradually increased up to the preset speed, and your vehicle
resumes fixed−speed cruising.
If the vehicle ahead decelerates abruptly or other vehicles cut in ahead of you, your vehicle may be too close to the vehicle ahead of you.
If this occurs, the multi−information display flashes and beeps. (Approach warning)
The dynamic radar cruise control should be used on roads in which sufficient vehicle−to−vehicle distance will be ensured
(such as on freeways).
1
This quick reference guide provides you with information on Dynamic Radar Cruise Control Vehicle−to−Vehicle Distance
Control Mode. Prior to use of this system, you should be thoroughly familiar with this system, referring to “Dynamic Radar
Cruise Control” in Section 3−1, Owner’s Manual in conjunction with this quick reference guide.

Cautions
If other vehicles are driving outside of the millimeter wave radar detection range, a delay in the detection of the vehicle cutting
in at short range or detection failure of the motorcycle running on the side of the same lane will occur. In this case, the dy-
namic radar cruise control system will not function properly.
The distance between your vehicle and the vehicle ahead cannot be accurately detected in the following cases:
The vehicle ahead or other vehicles around you are flinging up water or snow.
Heavy luggage is loaded in your trunk or on top of your rear seats, or is raising up the nose of your vehicle.
The rear section of the vehicle ahead is extremely small such as an unloaded trailer.
The millimeter wave radar sensor automatically detects dirt if it is sticking to the front of the sensor or grille cover of your
vehicle.
However, in some cases dirt may not be detected and an appropriate vehicle−to−vehicle distance cannot be maintained. Continue
driving with due care to the vehicle ahead.
Dynamic radar cruise control does not operate when the vehicle is at a stop or is driving very slowly.
Pay special attention to the very slow vehicle at the end of the line in heavy traffic or at the toll gate.
Turn off the “ON−OFF” button when dynamic radar cruise control is not in use.
The approach warning may not turn on even if the vehicle drives closer to the vehicle ahead in the following conditions:
Your vehicle and the vehicle ahead are cruising at almost the same speed.
The vehicle ahead is cruising at a faster speed than yours. (The distance between the vehicles will become longer.)
The accelerator pedal is depressed, immediately after the release of the accelerator pedal or immediately after the speed setting.
Depending on the road configuration (curved roads) or your vehicle condition (steering wheel maneuvering, position in the
lane), vehicles in other lanes or surrounding objects will be detected.
See Owner’s Manual for Complete Information.
4

Warning Display
If there is trouble somewhere in the dynamic radar cruise control while the vehicle−to−vehicle distance control mode is on, the “CRUISE”
indicator light in the instrument cluster flashes, the master warning light comes on and the warning tone sounds, and one or more of the
warning messages will appear on the multi−information display.
If a warning message appears on the display, take the appropriate measure referring to Section 3−1, “Owner’s Manual”.

Approach Warning
Dynamic radar cruise control and approach warning do not operate when the vehicle ahead is at a stop
or is driving much slower than your vehicle. Use caution for the vehicle at the end of the line in heavy
traffic or at the tollgate, the vehicle at a stop and the very slow vehicle.
If your vehicle approaches the vehicle ahead because of insufficient braking when the vehicle ahead deceler-
ates abruptly or when another vehicle cuts in ahead of you, the multi−information display flashes and beeps.
Depress the brake pedal to slow down, ensuring sufficient vehicle−to−vehicle distance.
Warning message
“CLEAN RADAR SENSOR”
“CRUISE NOT AVAILABLE”
“CHECK CRUISE SYSTEM”
If any warning message shown above appears, the preset
speed automatically cancels out.
Master Warning
Light Warning
Message
”CRUISE” Indicator
Light
5