2006 Lexus ES330 light

OCCUPANT RESTRAINT SYSTEM
clviii
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retracted even slightly, it cannot be
extended.
To hold the convertible seat securely, make sure the belt is in
the lock mode before letting the belt retract.3. While pressing the convertible seat firmly against the seat
cushion and seatback, let the shoulder belt retract as far as it
will go to hold the convertible seat securely.

OCCUPANT RESTRAINT SYSTEM
clx(C) Booster seat installation
A booster seat must be used in forwardfacing position
only.

Move seat fully back
CAUTION
A forwardfacing child restraint system should be
allowed to be installed on the front passenger seat
only when it is unavoidable. Always move the seat as
far back as possible even if the “AIRBAG OFF”
indicator light is illuminated, because the front
passenger airbag could inflate with considerable
speed and force. Otherwise, the child may be killed
or seriously injured.

OCCUPANT RESTRAINT SYSTEM
clxvi
Canada only
 Type B CHILD RESTRAINT SYSTEM INSTALLATION
1. Widen the gap between the seat cushion and seatback
slightly and confirm the position of the lower anchorages
near the button on the seatback.
2. Type A — Latch the hooks of lower straps onto the
anchorages and tighten the lower straps.
2. Type B — Latch the buckles onto the anchorages.
For owners in Canada —
The symbol on a child restraint
system indicates the presence of a lower connector system.
If your child restraint system has a top strap, it should be
anchored. (For the installation of the top strap, see “Using a top
strap” on page clxiii.)
For installation details, refer to the instruction manual equipped
with each product.

OCCUPANT RESTRAINT SYSTEM
clxviiiBy repeating these two steps and pressing the remaining
button,
the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
When you push button “1” or “2”, the driving position will
be automatically adjusted to the position recorded for that
button. Conditions for memorized position activation

Ignition key “ON” and selector lever in “P” position
 Ignition switch off and within 30 seconds of opening driver’s
door
If any driving position memory switch is pushed while one of the
memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1” or “2”)\
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.

OCCUPANT RESTRAINT SYSTEM
clxix
FRONT PASSENGER SEAT
POSITION MEMORY SYSTEM
The microcomputer can memorize the position of the front
passenger seat. Two different seat position profiles can be
entered into the computer’s memory.
Recording a seat position in the computer’s memory can only
be done when the ignition key is in the “ON” position and the
selector lever is in the “P” position.
Setting the front passenger seat position
1. Adjust the front passenger seat to the desired position.
2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.
The beep sound means that the positions are recorded in the
computer’s memory. By repeating these two steps and pressing the remaining
button, the seat position for another passenger can be
recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
When
you push button “1” or “2”, the seat position will be
automatically adjusted to the position recorded for that
button.

STEERING WHEEL AND MIRRORS
clxxivWhen you set your driving position:
1. Set the parking brake firmly.
2. Move the accelerator and brake pedals to the front most
position.
3. Adjust the seat position and steering wheel angle properly.
(See pages cviii and clxxiii.)
4. Move the pedals toward you
until you can fully depress the
brake pedal.
5. After adjusting, depress the pedals a few times to get used
to the feel.
CAUTION
 Never put your foot on the accelerator pedal while the
pedals are moving. It may cause racing of the engine
or sudden acceleration.
 Make sure that you can fully depress the brake pedal
before driving. Otherwise, you may not be able to
hold down the brake pedal firmly in an emergency
stop.
OUTSIDE REAR VIEW MIRRORS
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side
because it is a convex mirror. Any object seen in a convex
mirror will look smaller and farther away than if seen in a normal
flat mirror.
When the inside rear view mirror darkens in AUTO mode, the
outside rear view mirrors also darken to reduce the reflection
of the headlights of the following vehicle. For details, see
“Inside rear view mirror” on page clxxvii.

STEERING WHEEL AND MIRRORS
clxxvii
INSIDE REAR VIEW MIRROR
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the “MIRROR” switch changes the mode
between AUTO and DAY.
The indicator comes on when the AUTO mode is selected.
DAY mode: The mirror surface is normal.
AUTO mode: If the mirror detects light from the headlights
of the vehicle behind you, the mirror surface darkens
slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the AUTO mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the
driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.
To ensure correct functioning of antiglare mirror sensors
located on both sides of the mirror, do not touch or cover
the sensors with your finger or a piece of cloth, etc.

STEERING WHEEL AND MIRRORS
clxxxii
VANITY MIRRORS
To use the vanity mirror, swing the sun visor down and
open the cover.
To turn on the vanity light, slide the switch.
The vanity light switch has the following positions:
“ON” — Turns the light on when you swing down the sun visor.
However, if the visor has been slid out, the light may not come
on. Return the visor to its lock position.
“OFF” — Turns the light off.