2006 KIA Sorento ECU

To prevent the jack, jack handle,
wheel lug nut, wrench and spare tire
from rattling while the vehicle is in
motion, store them properly. To store
the flat fire, refer to “Storing the spare
tire”in this section.
IN CASE OF AN EMERGENCY
6-25
CAUTION
Your vehicle has metric threads
on the wheel studs and nuts.
Make certain during wheel
removal that the same nuts
removed are reinstalled - or, if
replaced, that nuts with metric
threads and the same chamfer
configuration are used.
Installation of a non-metric
thread nut on a metric stud or
vice-versa will not secure the
wheel to the hub properly and
will damage the stud so that it
must be replaced.
Note that most lug nuts do not
have metric threads. Be sure to
use extreme care in checking
for thread style before installing
aftermarket lug nuts or wheels.
If in doubt, consult an
Authorized Kia Dealer.
WARNING
- Wheel Studs
If the studs are damaged, they
may lose their ability to retain
the wheel. This could lead to the
loss of the wheel and a colli-
sion.
✽ ✽
NOTICECheck the inflation pressures as
soon as possible after installing the
spare tire. Adjust it to the specified
pressure, if necessary. Refer to
Section 8, Specifications.
BL-ENG (CAN)-6.qxd 7/28/05 5:57 PM Page 25

PARKING BRAKEChecking the Parking Brake
Check the stroke of the parking brake
by counting the number of “clicks’’
heard while fully applying it from the
released position. Also, the parking
brake alone should securely hold the
vehicle on a fairly steep grade. If the
number of “clicks’’is more or less
than specified, have the parking
brake adjusted by an authorized Kia
dealer.Stroke:
4~6 “clicks’’at a force of 22 lbs (10kg,
98N).
MAINTENANCE
7-15
S2BLC302B
CAUTION
Do not allow brake/clutch fluid
to contact the vehicle's body
paint, as paint damage will
result. Brake/clutch fluid, which
has been exposed to open air
for an extended time should
never be used as its quality can-
not be guaranteed. It should be
thrown out. Don't put in the
wrong kind of fluid. For exam-
ple, just a few drops of mineral-
based oil, such as engine oil, in
your brake clutch system can
damage brake clutch system
parts.
BL-ENG (CAN)-7.qxd 7/28/05 5:58 PM Page 15

Maintenance
For optimal battery performance:
Keep the battery securely mounted.
Keep the battery top clean and dry.
Keep the terminals and connections
clean, tight, and coated with petro-
leum jelly or terminal grease.Rinse any spilled electrolyte from
the battery immediately with a solu-
tion of water and baking soda.
If the vehicle is not going to be used
for an extended time, disconnect
the battery cables.
Items to be reset after the battery
has been replaced or the battery
cables have been disconnected
and reinstalled.
Sunroof (See page 3-83)
Clock (See page 4-67)
Multi-Meter (See page 4-52)
Climate control system (See pages
4-71 and 4-79)Battery Recharging
Your vehicle has a maintenance-free,
calcium-based battery.
If the battery becomes discharged
in a short time (because, for exam-
ple, the headlights or interior lights
were left on while the vehicle was
not in use), recharge it by slow
charging (trickle) for 10 hours.
If the battery gradually discharges
because of high electric load while
the vehicle is being used, recharge
it at 20-30A for two hours.MAINTENANCE7-24
S2BLA721
BL-ENG (CAN)-7.qxd 7/28/05 5:58 PM Page 24

4. Remove the bulbs by pulling them
straight out.
5. Install new bulbs in the socket.
6. Install the trim securely with the
fasteners.License Plate Light
1. Loosen the lens retaining screws
with a cross-tip screwdriver.
2. Remove the lens.
3. Remove the bulb by pulling it
straight out.
4. Install a new bulb.
5. Reinstall the lens securely with the
lens retaining screws.Rear Combination Light Bulb
Replacement
1. Open the rear hatch.
MAINTENANCE
7-39
S2BLA746A Stop/Tail light
Turn signal light
 Back up light
 Side marker light


S2BLA744A
S2BLA745
BL-ENG (CAN)-7.qxd 7/28/05 5:58 PM Page 39