2006 KIA Sorento ESP

Electric type (if equipped)
The electric day/night rearview mirror
automatically controls the glare from
the headlights of the car behind you.
Adjust the rearview mirror to the
desired position.
Press the “O”button to turn the auto-
matic- dimming function off. The mir-
ror indicator light will turn off.
Press the “I”button to turn the auto-
matic- dimming function on. The mir-
ror indicator light will illuminate.
INTERIOR LIGHTSMap Light
The lights are switched ON or OFF by
pressing the corresponding switches.
KNOWING YOUR VEHICLE3-76
P
U
S
HTILTSLIDE
S2BLA430JS2BLA430E
Type AType B
S2BLC301
CAUTION
Do not place objects in the rear
seat or cargo area which would
interfere with your vision out
the rear window.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 76

1. Make sure the parking brake is
applied.
2.Manual Transmission- Depress
the clutch pedal fully and shift the
transmission into Neutral. Keep the
clutch pedal depressed while turn-
ing the ignition switch to the start
position. The starter will not oper-
ate if the clutch pedal is not fully
depressed.
Automatic Transmission -Place
the transmission shift lever in P
(Park) or N (Neutral). Depress the
brake pedal fully.
3. While fully depressing the acceler-
ator, turn the ignition switch to the
START position and hold it (a max-
imum of 10 seconds) to discharge
the excess fuel.
If the engine starts, the engine
speed will increase suddenly;
release the key and the accelera-
tor immediately.4. If the engine has not yet started,
release the accelerator after crank-
ing the engine. Without depressing
the accelerator, crank the engine
until it starts (a maximum of 10
seconds).If the engine fails to start when
the engine is warm:
A no-start condition, characterized by
failure to restart a warmed engine
despite repeated attempts may be
eliminated by using the following pro-
cedure.
1. Make sure the parking brake is
applied.
2.Manual Transmission- Depress
the clutch pedal fully and shift the
transmission into Neutral. Keep the
clutch pedal depressed while turn-
ing the ignition switch to the start
position. The starter will not oper-
ate if the clutch pedal is not fully
depressed.
Automatic Transmission -Place
the transmission shift lever in P
(Park) or N (Neutral). Depress the
brake pedal fully.
DRIVING YOUR VEHICLE
4-5
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 5

Sports Mode
Whether the vehicle is stationary or in
motion, sports mode is selected by
pushing the shift lever from the “D”
position into the manual gate. To
return to “D”range operation, push
the shift lever back into the main
gate.In sports mode, moving the shift lever
backwards and forwards will allow
you to make gearshifts rapidly. In con-
trast to a manual transmission, the
sports mode allows gearshifts with
the accelerator pedal depressed.
Up (+) : Push the lever forward
once to shift up one gear.
Down (-) : Pull the lever backwards
once to shift down one
gear.DRIVING YOUR VEHICLE4-18
✽ ✽
NOTICE Upshifts do not take place auto-
matically in sports mode. The
driver must execute upshifts in
accordance with road conditions,
taking care to keep the engine
speed below the red zone.
 In sports mode, only the five for-
ward gears can be selected. To
reverse or park the vehicle, move
the shift lever to the “R” or “P”
position as required.
 In sports mode, downshifts are
made automatically when the
vehicle slows down. When the
vehicle stops, 1st gear is automat-
ically selected.
(Continued)
E4BLA402C + (UP)
- (DOWN) Automatic
modeSports mode
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 18

Full-Time 4WD Operation
(If equipped)
When 4WD is selected with the trans-
fer shift knob, the vehicle will switch
to 4WD operation after a few sec-
onds.To avoid shift shock, when the vehicle
is stopped and you make a transfer
case shift using the transfer shift
knob, wait until the corresponding
indicator light in the instrument clus-
ter illuminates before driving.Knob position
This is used to set different positions.
AUTO
Full power delivered to front and rear
axle for increased traction. Use this
mode for normal on-road driving.
The 4WD LOW indicator light ( )
will be turned off after blinking for a
few seconds to remind you that you
are in the AUTO mode.
LOW
Full power to both axles, including a
lower gear ratio for low speed appli-
cations that require extra power such
as wet pavement, snow-covered
roads and/or off-road.
LOW Mode is not recommended on
dry pavement.
The 4WD LOW indicator light ( )
will be turned on after blinking for a
few seconds to remind you that you
are in the LOW mode.
4WD
LOW4WD
LOW
DRIVING YOUR VEHICLE4-22
L
O
WAUTO
S2BLA411B
✽ ✽
NOTICEWhen the vehicle shifts into 4WD
mode, a slight mechanical sound
and vibration may be felt and does
not indicate a problem with the sys-
tem.
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 22

When 4WD is selected with the trans-
fer shift knob, the vehicle will switch
to 4WD operation after a few sec-
onds.
To avoid shift shock, when the vehicle
is stopped and you make a transfer
case shift using the transfer shift
know, wait until the corresponding
indicator light in the instrument clus-
ter illuminates before driving.Knob position
This is used to set different positions.
2HI(Rear-wheel drive)
This mode is used, when driving on
normal roads and highway.
4HI(High-range 4-wheel drive)
This mode is used, when driving off-
roads, wet or snow covered roads
with normal speed.
The 4WD indicator light ( ) will be
turned on to remind you that you are
in the 4HI mode.DRIVING YOUR VEHICLE4-24
✽ ✽
NOTICE Do not select four wheel drive on
flat and normal roads.
 Four-wheel driving on flat roads
for a long period causes poor fuel
economy and noise and it also
causes tires to wear faster.
 Four-wheel driving on flat and
normal roads can result in a
severe binding and chattering
condition when turning the steer-
ing wheel.
 Four-wheel driving on flat roads
for a long period can also cause
the differential oil temperature to
increase, resulting in damage to
parts in the power train.
✽ ✽
NOTICEWhen the vehicle shifts into 4WD
mode, a slight mechanical sound
and vibration may be felt and does
not indicate a problem with the sys-
tem.
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 24

4LO(Low-range 4-wheel drive)
Use 4LO for climbing or descending
hills, off-roads driving and towing the
vehicle, especially when increased
power is required.
The 4WD LOW indicator light ( )
will be turned on to remind you that
you are in the 4LO mode.
Transfer shift knob operation
By turning the transfer knob (4HI,
4LO), both front and rear axles are
engaged.
This improves the traction character-
istic.2HI➝ ➝
4HI
Turn the transfer knob from the 2HI
mode to 4HI mode at speed below
80km/h.
It is not necessary to depress the
clutch pedal or put the shift lever into
N (Neutral) position (Manual
Transmission) or put the shift lever
into N (Neutral) position (Automatic
Transmission).
Perform this operation when driving
straight. There will be a few seconds
of time delay before come into 4HI
mode when you shift the knob to 4 HI
from 2HI.
4HI ➝ ➝
2HI
Turn the transfer knob from the 4HI
mode to the 2HI mode at speed
below 80km/h. It is not necessary to
depress the clutch pedal (manual
transmission) or put the shift lever
into N (Neutral) (automatic transmis-
sion). Perform this operation when
driving straight. Perform this opera-
tion when driving straight.
If the transfer mode does not shift
into 2HI mode when you turn the
transfer knob to 2HI, drive straight
ahead with accelerating or decelerat-
ing, or drive in reverse.4HI ↔ ↔
4LO
1. Stop the vehicle.
2. Depress the clutch pedal for the
manual transmission or put the
shift lever into N (Neutral) for the
automatic transmission.
3.
4HI ➝ ➝
4LO: Select the 4LO mode.4LO➝ ➝
4HI: Select the 4HI mode.
4. Before releasing the clutch pedal
(Manual transmission) or shifting
to other ranges from N range
(Automatic transmission) ,wait for
corresponding indicator light turns
on or off in the cluster.
4WD
LOW
DRIVING YOUR VEHICLE
4-25
CAUTION
If the vehicle moves while the
transfer shift is in process, the
gearbox may be damaged.
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 25

The ABS system continuously sens-
es the speed of the wheels. If the
wheels are going to lock, the ABS
system repeatedly modulates the
hydraulic brake pressure to the
wheels.
When you apply your brakes under
conditions which may lock the
wheels, you may hear a “tik-tik’’
sound from the brakes, or feel a cor-
responding sensation in the brake
pedal. This is normal and it means
your ABS system is active.
In order to obtain the maximum ben-
efit from your ABS system in an
emergency situation, do not attempt
to modulate your brake pressure and
do not try to pump your brakes. Press
your brake pedal as hard as possible
or as hard as the situation warrants
and allow the ABS system to control
the force being delivered to the rear
brakes.Even with the anti-lock brake sys-
tem, your vehicle still requires suffi-
cient stopping distance. Always
maintain a safe distance from the
vehicle in front of you.
Always slow down when cornering.
The anti-lock brake system cannot
prevent accidents resulting from
excessive speeds.
On loose or uneven road surfaces,
operation of the anti-lock brake sys-
tem may result in a longer stopping
distance than for vehicles equipped
with a conventional brake system.
DRIVING YOUR VEHICLE
4-35
ABS
W-78
(Continued)
Driving too fast on poor road
surfaces. The ABS is
designed to improve maxi-
mum braking effectiveness on
typical highways and roads in
good condition. On poor road
surfaces in poor condition,
the ABS may actually reduce
braking effectiveness.
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 35

Immobilizer Indicator
When you turn the ignition key to the
ON position, if the IMMO indicator
goes off after blinking 6 times, this
indicates that the immobilizer system
is normal. However, if the IMMO indi-
cator remains on continuously after
blinking 6 times, this indicates that
the immobilizer system is out of order
and you cannot start the engine with-
out the limp home procedure. Refer
to the “Limp home procedure”on
page 3-4.Malfunction Indicator
The CHECK ENGINE or malfunction
indicator light is installed in your vehi-
cle’s instrument panel and responds
to signals from the vehicle’s On
Board Diagnostic (OBD -II) System.
The OBD-II System monitors the per-
formance of the vehicle’s Emission
Control System (ECS), which is
designed to reduce the amount of air
pollutants in engine exhaust to the
levels required by government regu-
lations.
When you first start the engine, the
check engine light will illuminate
briefly as a system check to confirm
that the OBD-II System is operating
properly. As the engine starts, this
light turns off. However, if at any time
the OBD-II system detects a faulty
signal or determines that the ECS is
not performing to specification, the
CHECK ENGINE light will illuminate
continuously or flash.Continuously ON :
If the CHECK ENGINE light comes
ON while driving and illuminates con-
tinuously, a potential problem has
been discovered in the ECS or one of
the exhaust system components.
Generally, the vehicle will continue to
be driveable but it should be checked
by an authorized Kia dealer as soon
as possible. This condition is unlikely
to lead to engine damage unless a
decrease in vehicle power or poor
running conditions is immediately
apparent.
Note that the CHECK ENGINE light
will illuminate for a problem like a
loose or missing gas cap, but will not
illuminate as a result of low engine oil
or coolant, low automatic transaxle
fluid or engine overheating. The driv-
er will be alerted to these conditions
by other indicators on the instrument
panel
DRIVING YOUR VEHICLE
4-49
CHECK
IMMO
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 49