2006 INFINITI QX56 remote control

TELEPHONEAV-69
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Terminals and Reference Value for Bluetooth Control UnitEKS00GBO
Terminal
(Wire color) ItemSignal
input/
output Condition
Reference value
(Approx.) Example of symptom
+ – Ignition
switch Operation
1 (Y) Ground Battery
powerInput
–– Battery voltageSystem does not
work properly.
2 (V) Ground ACC power Input ACC/
ON –
Battery voltage System does not
work properly.
3 (G/R) Ground IGN power Input ON/
START –
Battery voltage System does not
work properly.
4 (B) –Ground –– – ––
6 –Shield –– – ––
7 (B) 8 (R/L) Mic-in signal Input ON –– –
9 (R/W) 10 (R) Audio out Output ––––
11 ( B ) –Mute –– – ––
12 (R/G) Ground Remote
control A Input ON Press MODE
switch Approx. 0V
Steering wheel audio
controls do not func-
tion.
Press SEEK UP
switch Approx. 0.75V
Press VOL UP switch Approx. 2V
Except for above Approx. 5V
13 (G/W) Ground Remote
control B Input ON Press POWER
switch Approx. 0V
Steering wheel audio
controls do not func-
tion.
Press SEEK
DOWN switch Approx. 0.75V
Press VOL
DOWN switch Approx. 2V
Except for above Approx. 5V
14 (Y/R) - Remote
control
ground -- -
-Steering wheel audio
controls do not func-
tion.
15 (GR) - LED - - -- -
17 (V) Ground AV switch 1 Output On Press MODE
switch Approx. 0V
Steering wheel audio controls do not func- tion.
Press SEEK UP
switch Approx. 0.75V
Press VOL UP switch Approx. 2V
Except for above Approx 5V
18 (G/O) Ground AV switch 2 Output ON Press POWER
switch Approx. 0V
Steering wheel audio controls do not func- tion.
Press SEEK
DOWN switch Approx. 0.75V
Prees VOL
DOWN switch Approx. 2V
Except for above Approx 5V
19 (R/B) - AV switch
ground -- -
-Steering wheel audio
controls do not func- tion.
21 (B) - Ground - - -- –

DVD ENTERTAINMENT SYSTEMAV-81
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Trouble DiagnosisEKS00BJ9
SymptomPossible causes Repair order
DVD player inoperative 1. Power supply
2. Ground circuit
3. Audio enable circuit
4. DVD enable signal
5. Audio enable signal
6. DVD player
7. Audio unit 1. Refer to AV- 8 2 , "
Power Supply Circuit Inspection" .
2. Refer to AV- 8 2 , "
Power Supply Circuit Inspection" .
3. Check audio enable circuits for open or short between audio unit terminals 39, 40 and DVD player terminals
11 , 9 .
4. Push power switch of DVD player and verify approx. 5V is present at terminal 39 of audio unit.
5. Push power switch of DVD player and verify approx. 5V is present at terminal 9 of DVD player.
6. Remove DVD player for repair.
7. Remove audio unit for repair.
No sound when playing
DVD 1. Audio signal circuits
2. DVD player
3. Audio unit 1. Check audio signal circuits for open or short between
DVD player terminals 1, 2, 3 and 4 and audio unit ter-
minals 34, 35, 36 and 37.
2. Remove DVD player for repair.
3. Remove audio unit for repair.
Video monitor is inopera-
tive/does not operate prop-
erly 1. Power supply
2. Video monitor ground circuit
3. Video circuits
4. Data signal
5. Video monitor
6. DVD player 1. Operate DVD player and verify battery positive voltage
is present at terminals 11 and 12 of video monitor. Ver-
ify approximately 5 volts is present at terminal 10 of
video monitor.
2. Check video monitor ground circuits between DVD player terminals 19 and 27 and video monitor terminals
1 and 2.
3. Check video circuits between DVD player terminals 23 and 24 and video monitor terminals 7 and 8.
4. Check data signal circuit for open or short between DVD player terminal 29 and video monitor terminal 5.
5. Remove video monitor for repair.
6. Remove DVD player for repair.
DVD remote control is
inoperative/does not oper-
ate properly 1. Data signal
2. DVD player remote control batteries
3. DVD player remote control
4. Video monitor 1. Check data signal circuit for open or short between
DVD player terminal 28 and video monitor terminal 6.
2. Replace DVD player remote control batteries.
3. Replace DVD player remote control.
4. Remove video monitor for repair.
Headphones inoperative 1. Headphone batteries 2. Headphones
3. Rear audio remote control unit 1. Replace headphone batteries.
2. Replace headphones.
3. Replace rear audio remote control unit.
Snowy video/poor audio 1. Harness or connectors 2. DVD player 1. Check harness and connectors for open or short.
2. Check DVD player.
Snowy video (audio OK) 1. Harness or connectors 2. DVD player 1. Check harness and connectors for open or short.
2. Check DVD player.
No video (audio OK) 1. Harness or connectors 2. DVD player
3. Video monitor 1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.
Dim video (audio OK) 1. Harness or connectors 2. DVD player
3. Video monitor 1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.

AV-108
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Terminals and Reference Value for AV SwitchEKS00BJN
Terminal No.
(Wire color) ItemSignal
input/
output Condition
Voltage
(Approx.) Example of
symptom
+ – Ignition
switch Operation
1 (Y) Ground Battery
power Input OFF
-Battery voltage System does not
work properly.
2 (V) Ground ACC signal Input ACC -Battery voltage System does not
work properly.
3 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (position 1).
Battery voltageAV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1).
Turn lighting switch
OFF.
3.0V or less
4 (BR) Ground Illumination
control signal Input ON Illumination control
switch is operated
by lighting switch in
1st position. Changes between 0 and 12V.
AV switch illumi-
nation cannot be
controlled.
5 (B) Ground Ground - ON -0V -
6 (V) Ground Communica-
tion signal (+) Input/
output ON
- System does not
work properly.
7- Shield
ground -- -
--
8 (LG) Ground Communica-
tion signal (-) Input/
output ON
- System does not
work properly.
12 (R) Ground Remote con-
trol A Input ON Press MODE
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK UP
switch 0.75V
Press VOL UP switch 2V
Except for above 5V
13 (G) Ground Remote con-
trol B Input ON Press POWER
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK
DOWN switch 0.75V
Press VOL DOWN switch 2V
Except for above 5V
14 (L) - Remote con-
trol ground -- -
-Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E

BCM (BODY CONTROL MODULE)BCS-7
C
DE
F
G H
I
J
L
M A
B
BCS
Revision: November 2009 2006 QX56

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (insert)
–Hazard switch
–Main door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back latch (door ajar switch)
–Glass hatch ajar switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door lock assembly LH (key cylinder switch)

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE

Sunroof system. Refer to RF-10, "SUNROOF" . NOTE

Room lamp timer. Refer to LT- 1 3 4 , "INTERIOR ROOM LAMP" .

Warning chime system. Refer to DI-43, "WARNING CHIME" .

Turn signal and hazard warning lamps system. Refer to LT- 8 0 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .

Trailer turn signal and hazard warning lamps system (if equipped). Refer to LT- 1 2 6 , "TRAILER TOW" .

Rear wiper and washer system. Refer to WW-32, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security system. Refer to BL-75, "VEHICLE SECURITY (THEFT WARNING) SYSTEM" .

IVIS (NATS) system. Refer to BL-137, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .

Headlamp, tail lamp, front fog lamp, auto light and battery saver control systems. Refer to LT- 5 , "HEAD-
LAMP (FOR USA)" , LT- 3 3 , "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT- 111 ,
"PARKING, LICENSE PLATE AND TAIL LAMPS" , LT- 6 9 , "FRONT FOG LAMP" or LT- 4 7 , "AUTO LIGHT
SYSTEM" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-74, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System InputOutput
Remote keyless entry system Remote keyless entry receiver (keyfob)

All door locking actuators

Back door opener actuator

Turn signal lamps
Power door lock system

Front power door lock/unlock switch (LH, RH)

All door switches

Key switch All door locking actuators

BCS-8
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
CAN Communication System DescriptionEKS00D7X
Refer to LAN-26, "CAN COMMUNICATION" .
Power supply [ignition (IGN)/retained
accessory power (RAP)] to power win-
dow and sunroof IGN/RAP supply
Power supply to power window and
sunroof system
Power supply (BAT) to power window
and sunroof Battery power supply Power supply to power window and
sunroof system
Panic alarm

Key switch

Remote keyless entry receiver (keyfob) IPDM E/R
Auto light system

Optical sensor

Combination switch IPDM E/R
Battery saver control

Ignition switch

Combination switch

Front door switch LH and RH IPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Front door lock assembly LH (key cylinder switch)

All door switches Interior room lamp
Key warning chime

Key switch

Front door switch LH Combination meter (warning
buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LH Combination meter (warning
buzzer)
Vehicle-speed-sensing intermittent
wiper

Combination switch

Combination meter IPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECM
Low tire pressure warning system Remote keyless entry receiver

Combination meter

Display control unit
Trailer tow (if equipped) Combination switch Trailer turn signal relays
Vehicle security system

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Power window and door lock/unlock switch RH

Front door lock assembly LH (key cylinder switch)

All door switches

Back door latch (door ajar switch)

IPDM E/R

Security indicator lamp
System
InputOutput

BCS-12
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
4. Select item to be diagnosed on “SELECT TEST ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
LKIA0183E
System and item CONSULT-II
display Diagnostic test mode (Inspection by part)
WORK
SUPPORT SELF−
DIAG
RESULTS CAN DIAG
SUPPORT MNTR DATA
MONITOR ECU
PA R T
NUMBER ACTIVE
TEST CON-
FIGU-
RATION
BCM BCM××× × ×
Power door lock system DOOR LOCK ×× ×
Rear defogger REAR
DEFOGGER ××
Warning chime BUZZER ××
Room lamp timer INT LAMP ×× ×
Remote keyless entry
system MULTI REMOTE
ENT
××
×
Headlamp HEAD LAMP×× ×
Wiper (front/rear) WIPER ×× ×
Turn signal lamp
Hazard lamp FLASHER
××
Blower fan switch signal
Air conditioner switch
signal AIR
CONDITIONER
×
Combination switch COMB SW ×
IVIS (NATS) IMMU ××
Interior lamp battery
saver BATTERY
SAVER
××
×
Back door TRUNK ××
Theft alarm THEFT ALM×× ×
Retained accessory
power control RETAINED PWR
×× ×
Oil pressure switch SIGNAL BUFFER ××
Air pressure monitor AIR PRESSURE
MONITOR××
× ×
Panic alarm PANIC ALARM ×

BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
DE
F
G H
J
K L
M
SECTION
A
B
BL
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
Precautions for work ................................................ 4
PREPARATION ...................................................... ..... 5
Special service tool ............................................. ..... 5
Commercial Service Tool .................................... ..... 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 6
Work Flow ................................................................ 6 CUSTOMER INTERVIEW ................................ ..... 6
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 7
CHECK RELATED SERVICE BULLETINS ...... ..... 7
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 7
REPAIR THE CAUSE ...................................... ..... 7
CONFIRM THE REPAIR .................................. ..... 8
Generic Squeak and Rattle Troubleshooting ...... ..... 8
INSTRUMENT PANEL ..................................... ..... 8
CENTER CONSOLE ........................................ ..... 8
DOORS ............................................................ ..... 8
TRUNK ............................................................. ..... 9
SUNROOF/HEADLINING ................................ ..... 9
OVERHEAD CONSOLE (FRONT AND REAR) ..... 9
SEATS .............................................................. ..... 9
UNDERHOOD .................................................. ..... 9
Diagnostic Worksheet ......................................... ... 10
HOOD .................................................................... ... 12
Fitting Adjustment ............................................... ... 12
CLEARANCE AND SURFACE HEIGHT
ADJUSTMENT ................................................. ... 13
HOOD LOCK ADJUSTMENT .......................... ... 13
Removal and Installation of Hood Assembly ....... ... 13
Removal and Installation of Hood Lock Control .. ... 14
REMOVAL ........................................................ ... 14
INSTALLATION ................................................ ... 15
Hood Lock Control Inspection ............................. ... 15
POWER DOOR LOCK SYSTEM ........................... ... 16
Component Parts and Harness Connector Location ... 16
System Description ............................................. ... 17OUTLINE ..........................................................
... 18
Schematic ............................................................ ... 19
Wiring Diagram — D/LOCK — ............................ ... 20
Terminals and Reference Value for BCM ............ ... 25
Work Flow ............................................................... 25
CONSULT–II Function (BCM) ............................. ... 26
CONSULT–II INSPECTION PROCEDURE ...... ... 26
DATA MONITOR .............................................. ... 27
ACTIVE TEST ..................................................... 28
Trouble Diagnoses Symptom Chart .................... ... 29
BCM Power Supply and Ground Circuit Check ... ... 29
Door Switch Check ................................................. 31
Key Switch (Insert) Check ................................... ... 33
Door Lock/Unlock Switch Check ............................ 34
Glass Hatch Switch Circuit Inspection ................. ... 36
Front Door Lock Assembly LH (Actuator) Check . ... 38
Front Door Lock Actuator RH Check ................... ... 39
Rear Door Lock Actuator RH/LH Check .............. ... 40
Glass Hatch Lock Actuator Check .......................... 41
Front Door Lock Assembly LH (Key Cylinder Switch)
Check .................................................................. ... 42
REMOTE KEYLESS ENTRY SYSTEM .................. ... 44
Component Parts and Harness Connector Location ... 44
System Description .............................................. ... 45
INPUTS ............................................................ ... 45
OPERATING PROCEDURE ............................. ... 46
CAN Communication System Description ........... ... 48
Schematic ............................................................ ... 49
Wiring Diagram — KEYLES — ............................ ... 50
......................................................................... ... 50
......................................................................... ... 51
......................................................................... ... 52
Terminals and Reference Value for BCM ............ ... 53
Terminals and Reference Value for IPDM E/R .... ... 54
CONSULT-II Function (BCM) .............................. ... 55
CONSULT-II Inspection Procedure ...................... ... 55
“MULTI REMOTE ENT” .................................... ... 55
CONSULT-II Application Items ............................ ... 56
“MULTI REMOTE ENT” .................................... ... 56
Trouble Diagnosis Procedure .............................. ... 59

REMOTE KEYLESS ENTRY SYSTEMBL-45
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
System DescriptionEIS005ZQ
INPUTS
Power is supplied at all times

to BCM terminal 70

through 50A fusible link (letter f , located in the fuse and fusible link box).

to BCM terminal 57

through 15A fuse [No. 22, located in the fuse block (J/B)].
When the key is inserted in the key switch and key lock solenoid, power is supplied

to BCM terminal 37

through key switch and key lock solenoid terminals 3 and 4

through 10A fuse [No. 19, located in the fuse block (J/B)].
When the ignition switch is ACC or ON, power is supplied

to BCM terminal 11

through 10A fuse [No. 4, located in the fuse block (J/B)].
When the ignition switch is ON or START, power is supplied

to BCM terminal 38

through 10A fuse (No. 59, located in the fuse and relay box).
When the front door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 47

through front door switch LH terminal 2

through front door switch LH case ground.
When the front door switch RH is ON (door is OPEN), ground is supplied

to BCM terminal 12

through front door switch RH terminal 2

through front door switch RH case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 48

through rear door switch LH terminal 2

through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied

to BCM terminal 13

through rear door switch RH terminal 2

through rear door switch RH case ground.
When the back door latch (door ajar switch) is ON (door is OPEN), ground is supplied

to BCM terminal 43

through back door latch (door ajar switch) terminal 7,

through back door latch (door ajar switch) terminal 8,

through body grounds B7 and B19.
Keyfob signal is input into the BCM from the remote keyless entry receiver.
The remote keyless entry system controls operation of the

power door lock

back door opener

interior lamp and step lamps

panic alarm

hazard and horn reminder

keyless power window down (open)

auto door lock operation