2006 INFINITI G35 tow

Fastening the seat belts 1. Adjust the seat. See ªSeatsº earlier in
this section.
2. Slowly pull the seat belt out of the re-
tractor and insert the tongue into the
buckle until it clicks.
· The retractor is designed to lock dur-
ing a sudden stop or on impact. A
slow pulling motion will permit the
belt to move, and allow you some
freedom of movement in the seat. · If the seat belt cannot be pulled from
its fully retracted position, firmly pull
the belt and release it. Then
smoothly pull the belt out of the re-
tractor. 3. Position the lap belt portion low and
snug on the hips as shown.
4. Pull the shoulder belt portion toward
the retractor to take up extra slack. Be
sure the shoulder belt is routed over
your shoulder and across your chest.
The front passenger and rear seat belts
have a locking mechanism for child re-
straint installation. It is referred to as the
automatic locking mode.
When the locking mechanism is activated
the seat belt cannot be extended again
until the seat belt tongue is detachedSSS0292
Front seat SSS0293
Rear seat SSS0290
Front seat
1-14 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

WARNINGDo not use towels, books, pillows or other
items in place of a booster seat. Items such
as these may move during normal driving or
a collision and result in serious injury or
death. Booster seats are designed to be
used with a lap/shoulder belt. Booster seats
are designed to properly route the lap and
shoulder portions of the seat belt over the
strongest portions of a child's body to provide the maximum protection during a
collision.
Booster seats of various sizes are offered
by several manufacturers. When selecting
any booster seat, keep the following
points in mind:
O Choose only a booster seat with a
label certifying that it complies with
Federal Motor Vehicle Safety Standard
213 or Canadian Motor Vehicle Safety
Standard 213.
O Check the booster seat in your vehicle
to be sure it is compatible with the ve-
hicle's seat and seat belt system. O Make sure the child's head will be
properly supported by the booster
seat or vehicle seat. The seatback
must be at or above the center of the
child's ears. For example, if a low back
booster seat
q 1
is chosen, the vehicle
seatback must be at or above the cen-
ter of the child's ears. If the seatback
is lower than the center of the child's
ears, a high back booster seat
q 2
should be used.
O If the booster seat is compatible with
your vehicle, place your child in the
booster seat and check the various
adjustments to be sure the boosterLRS0455 LRS0453 LRS0464
1-32 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

BOOSTER SEAT INSTALLATION ON
REAR SEAT OUTBOARD OR CENTER
POSITIONS
CAUTIONDo not use a lap/shoulder belt automatic
locking mode when using a booster seat
with the seat belts.
When you install a booster seat in the
rear seat, follow these steps: 1. Position the booster seat on the seat.
Only place it in a front-facing direc-
tion. Always follow the booster seat
manufacturer's instructions.
2. The booster seat should be positioned
on the vehicle seat so that it is stable.
If necessary, adjust or remove the
head restraint to obtain the correct
booster seat fit. See ªHead restraint
adjustmentº earlier in this section. If
the head restraint is removed, store it
in a secure place. Be sure to install
the head restraint when the booster
seat is removed. If the seating posi-
tion does not have an adjustable head restraint and it is interfering with the
proper booster seat fit, try another
seating position or a different booster
seat.
3. Position the lap portion of the seat
belt low and snug on the child's hips.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
4. Pull the shoulder belt portion of the
seat belt toward the retractor to take
up extra slack. Be sure the shoulder
belt is positioned across the top,
middle portion of the child's shoulder.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
5. Follow the warnings, cautions and in-
structions for properly fastening a seat
belt shown in the ªThree-point type
seat belts with retractorº earlier in
this section.LRS0452
Outboard position LRS0451
Center position
1-34 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

BOOSTER SEAT INSTALLATION ON
FRONT PASSENGER SEAT
WARNINGINFINITI recommends that child restraints be
installed in the rear seat. However, if you
must install a booster seat in the front pas-
senger seat, move the passenger seat to the
rearmost position. Also be sure that the front
passenger air bag status light is illuminated
to indicate the passenger air bag is OFF. See ªFront passenger air bag and status
lightº later in this section for details.
If you must install a booster seat in the
front seat, follow these steps:
1. Move the seat to the rearmost posi-
tion.
2. Position the booster seat on the seat.
Only place it in a front-facing direc-
tion. Always follow the booster seat
manufacturer's instructions.
3. The booster seat should be positioned
on the vehicle seat so that it is stable.
If necessary, adjust or remove the
head restraint to obtain the correct
booster seat fit. See ªHead restraint
adjustmentº earlier in this section. If
the head restraint is removed, store it
in a secure place. Be sure to install
the head restraint when the booster
seat is removed. If the seating posi-
tion does not have an adjustable head
restraint and it is interfering with the
proper booster seat fit, try another
seating position or a different booster
seat. 4. Position the lap portion of the seat
belt low and snug on the child's hips.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
5. Pull the shoulder belt portion of the
seat belt toward the retractor to take
up extra slack. Be sure the shoulder
belt is positioned across the top,
middle portion of the child's shoulder.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
6. Follow the warnings, cautions and in-
structions for properly fastening a seat
belt shown in the ªThree-point type
seat belt with retractorº earlier in this
section.
7. Turn the ignition switch to the ON po-
sition. The passenger air bag status
light should illuminate. If this
light is not illuminated, see ªFront
passenger air bag and status lightº
later in this section. Move the booster
seat to another seating position. Have
the system checked by an INFINITI
dealer.LRS0454
Safety Ð Seats, seat belts and supplemental restraint system
1-35
w 06.1.4/V35-D/V5.0
X

Other supplemental front air bag precau-
tions
WARNINGO Do not place any objects on the steering
wheel pad or on the instru-ment panel.
Also, do not place any objects between
any occupant and the steering wheel or
instrument panel. Such objects may be-
come dangerous projectiles and cause
injury if the supplemental front air bag
inflates.
O Immediately after inflation, several front
air bag system components will be hot.
Do not touch them; you may severely
burn yourself.
O No unauthorized changes should be
made to any components or wiring of the
supplemental air bag system. This is to
prevent accidental inflation of the
supplemental air bag or damage to the
supplemental air bag system.
O Do not make unauthorized changes to
your vehicle's electrical system, suspen-
sion system or front end structure. This could affect proper operation of the
supplemental front air bag system.
O Tampering with the supplemental front
air bag system may result in serious per-
sonal injury. Tampering includes
changes to the steering wheel and the
instrument panel assembly by placing
material over the steering wheel pad and
above the instrument panel or by install-
ing additional trim material around the
air bag system.
O Modifying or tampering with the front
passenger seat may result in serious
personal injury. For example, do not
change the front seats by placing mate-
rial on the seat cushion or by installing
additional trim material, such as seat
covers, on the seat. Additionally, do not
stow any objects under the front passen-
ger seat or the seat cushion and seat-
back. Such objects may interfere with
the proper operation of the occupant
classification sensor (pressure sensor). O No unauthorized changes should be
made to any components or wiring of the
seat belt system. This may affect the
supplemental front air bag system. Tam-
pering with the seat belt system may re-
sult in serious personal injury.
O Work around and on the supplemental
front air bag system should be done by
an INFINITI dealer. Installation of elec-
trical equipment should also be done by
an INFINITI dealer. The yellow and or-
ange Supplemental Restraint System
(SRS) wiring and connectors should not
be modified or disconnected. Unautho-
rized electrical test equipment and prob-
ing devices should not be used on the air
bag system.
O A cracked windshield should be replaced
immediately by a qualified repair facility.
A cracked windshield could affect the
function of the supplemental air bag
system.
O The SRS wiring harness connectors are
yellow and orange for easy
identification.
Safety Ð Seats, seat belts and supplemental restraint system
1-47
w 06.1.4/V35-D/V5.0
X

Stowing golf bags (Coupe) ........................ 2-39
Windows......................................................... 2-39
Power windows ......................................... 2-39
Automatic adjusting function (Coupe) ........ 2-41
Sunroof (if so equipped) ................................. 2-42
Automatic sunroof ..................................... 2-42
Interior lights ................................................. 2-44
Room light ................................................ 2-44
Map lights................................................. 2-44
Personal lights ......................................... 2-45
Vanity mirror light (if so equipped)................. 2-46
Trunk light...................................................... 2-46 HomeLink
Universal Transceiver (if so
equipped) ....................................................... 2-46
Programming HomeLink
........................... 2-47
Programming HomeLink
for Canadian
customers ................................................. 2-48
Operating the HomeLink
Universal
Transceiver ................................................ 2-49
Programming trouble-diagnosis ................. 2-49
Clearing the programmed information ....... 2-49
Reprogramming a single HomeLink
button ....................................................... 2-49
If your vehicle is stolen ............................. 2-50
w 06.1.5/V35-D/V5.0
X

Low brake fluid warning light:
The light warns of a low brake fluid level.
If the light comes on while the engine is
running with the parking brake not ap-
plied, stop the vehicle and perform the
following:
1. Check the brake fluid level. Add brake
fluid as necessary. See ªBrake fluidº
in the ª8. Maintenance and do-it-
yourselfº section.
2. If the brake fluid level is correct, have
the warning system checked by an
INFINITI dealer.
Anti-lock Brake System (ABS) warning
indicator:
When the parking brake is released and
the brake fluid level is sufficient, if both
the brake warning light and the anti-lock
brake system warning light illuminate, it
may indicate the anti-lock brake system is
not functioning properly. Have the brake
system checked by an INFINITI dealer. See
ªAnti-lock brake warning lightº earlier in
this section. WARNING O Your brake system may not be working
properly if the warning light is on.
Driving could be dangerous. If you judge
it to be safe, drive carefully to the
nearest service station for repairs. Oth-
erwise, have your vehicle towed because
driving it could be dangerous.
O Pressing the brake pedal with the engine
stopped and/or a low brake fluid level
may increase your stopping distance
and braking will require greater pedal ef-
fort as well as pedal travel.
O If the brake fluid level is below the MINI-
MUM or MIN mark on the brake fluid res-
ervoir, do not drive until the brake
system has been checked by an INFINITI
dealer.
Charge warning light If the light comes on while the engine is
running, it may indicate that the charging
system is not functioning properly. Turn
the engine off and check the alternator belt. If the belt is loose, broken, missing
or if the light remains on, see an INFINITI
dealer immediately.
CAUTION Do not continue driving if the generator belt
is loose, broken or missing.
Door open warning light This light comes on when any of the
doors are not closed securely while the
ignition switch is in the ON position.
Engine oil pressure warning
light This light warns of low engine oil pres-
sure. If the light flickers or comes on dur-
ing normal driving, pull off the road in a
safe area, stop the engine immediately
and call an INFINITI dealer or other autho-
rized repair shop.
The engine oil pressure warning light is
not designed to indicate a low oil level.
Use the dipstick to check the oil level. See
ªEngine oilº in the ª8. Maintenance and
do-it-yourselfº section.
Instruments and controls
2-11
w 06.1.4/V35-D/V5.0
X

Cruise set switch indicator
lightThe light comes on while the vehicle
speed is controlled by the cruise control
system. If the light blinks while the en-
gine is running, it may indicate the cruise
control system is not functioning prop-
erly. Have the system checked by an
INFINITI dealer.
Front passenger air bag
status lightThe front passenger air bag status light,
located on the center display, will be lit
and the passenger front air bag will be off
depending on how the front passenger
seat is being used.
For front passenger air bag status light
operation, see ªINFINITI advanced air bag
systemº in the ª1. Safety Ð Seats, seat
belts and supplemental restraint systemº
section of this manual.
High beam indicator light
(Blue)This light comes on when the headlight
high beam is on and goes out when the
low beam is selected. Malfunction indicator lamp
(MIL) If the malfunction indicator lamp (MIL)
comes on steady or blinks while the en-
gine is running, it may indicate a poten-
tial emission control malfunction.
The malfunction indicator lamp may also
come on steady if the fuel-filler cap is
loose or missing, or if the vehicle runs out
of fuel. Check to make sure the fuel-filler
cap is installed and closed tightly, and
that the vehicle has at least three gallons
(14 liters) of fuel in the fuel tank.
After a few driving trips, the lamp
should turn off if no other potential emis-
sion control system malfunction exists.
If this indicator lamp comes on steady for
20 seconds and then blinks for 10 sec-
onds when the engine is not running, it
indicates that the vehicle is not ready for
an emission control system inspection/
maintenance test. See ªReadiness for
inspection/maintenance (I/M) testº in the
ª9. Technical and consumer informationº
section of this manual.
Operation
The malfunction indicator lamp will come on in one of two ways:
O Malfunction indicator lamp on steady
Ð An emission control system mal-
function has been detected. Check the
fuel-filler cap. If the fuel-filler cap is
loose or missing, tighten or install the
cap and continue to drive the vehicle.
The lamp should turn off after a
few driving trips. If the lamp
does not turn off after a few driving
trips, have the vehicle inspected by an
INFINITI dealer. You do not need to
have your vehicle towed to the re-
tailer.
O Malfunction indicator lamp blinking Ð
An engine misfire has been detected
which may damage the emission con-
trol system. To reduce or avoid emis-
sion control system damage:
a) Do not drive at speeds above 45
MPH (72 km/h).
b) Avoid hard acceleration or decel-
eration.
c) Avoid steep uphill grades.
d) If possible, reduce the amount of
cargo being hauled or towed.
The malfunction indicator lamp may
stop blinking and come on steady.
Instruments and controls
2-15
w 06.1.4/V35-D/V5.0
X