2006 INFINITI G35 display

rectionº anytime the system is waiting for
a response.
When you get used to the menus in the
system, you can talk ahead by saying
more than one command at a time. For
example, say, ªCall five five five one two
one twoº or ªMemo pad record.º
Also, when you get used to the system re-
sponses, you can skip ahead to the tone
by pressing the button on the steer-
ing wheel. However, if you press the
button when the system is waiting
for a response from you it will end the VR
session.
ªCallº
Name (speak name)
q A
If you have stored entries in the Phone
Book, you can dial a number associated
with a name and location. See ªPhone bookº later in this section to
learn how to store entries.
When prompted by the system, say the
name of the phone book entry you wish to
call. The system acknowledges the name.
If there are multiple locations associated
with the name, the system asks you to
choose the location.
Once you have confirmed the name and
location, the system begins the call.
Number (speak digits)
q B
When prompted by the system, say the
number you wish to call. Refer to ªHow to
say numbersº and ªMaking a call by en-
tering a phone numberº earlier in this
section for more details.
ªRedialº
q C
Use the Redial command to call the last
number that was dialed within the ve-
hicle.
NOTE:
The system will not redial the last number
dialed by the handset keypad.
The system acknowledges the command,
repeats the number and begins dialing. If a redial number does not exist, the sys-
tem announces, ªThere is no number to
redialº and ends the VR session.
ªCall backº
q D
Use the Call Back command to dial the
number of the last incoming call within
the vehicle.
The system acknowledges the command,
repeats the number and begins dialing. If
a call back number does not exist, the
system announces, ªThere is no number
to call backº and ends the VR session.
During a call
During a call there are several command
options available. Press the button
on the steering wheel to mute the receiv-
ing voice and enter commands.
O ªHelpº Ð The system announces the
available commands.
O ªGo back/Correctionº Ð The system
announces ªGo back,º ends the VR
session and returns to the call.
O ªCancel/Quitº Ð The system an-
nounces ªCancel,º ends the VR ses-
sion and returns to the call.
Display screen, heater, air conditioner and audio systems
4-37
w 06.1.4/V35-D/V5.0
X

O ªSend/Enter/Call/Dialº Ð Use the
Send command to enter numbers dur-
ing a call. For example, if you were di-
rected to dial an extension by an auto-
mated system:
Say: ªSend one two three four.º
The system acknowledges the com-
mand and sends the tones associated
with the numbers. The system then
ends the VR session and returns to
the call.
O ªTransfer callº Ð Use the Transfer Call
command to transfer the call from the
Bluetooth Hands-Free Phone System
to the cellular phone when privacy is
desired.
The system announces, ªTransfer call.
Call transferred to privacy mode.º The
system then ends the VR session.
You can also issue the Transfer Call
command again to return to a hands-
free call through the vehicle.
O ªMuteº Ð Use the Mute command to
mute your voice so the other party
cannot hear it. Use the mute command
again to unmute your voice. NOTE:
If the other party ends the call or the cellu-
lar phone network connection is lost while
the Mute feature is on, the Mute feature
may need to be reset to ªoff.º
ªPhone bookº
The Phone Book stores up to 40 names for
each phone paired with the system. Each
name can have up to 4 locations/phone
numbers associated with it.
NOTE:
Each phone has its own separate phone
book. You cannot access Phone A's phone
book if you are currently connected with
Phone B.
ªNew entryº
q A
Use the New Entry command to store a
new name in the system. When prompted by the system, say the
name you would like to give the new
entry.
For example, say: ªMary.º
If the name is too long or too short, the
system tells you, then prompts you for a
name again.
Also, if the name sounds too much like a
name already stored, the system tells
you, then prompts you for a name again.
Once the system accepts the name and
you confirm it is correct, the system asks
for a location (Home, Office, Mobile or
Other).
For example, say: ªHome.º
The system acknowledges the location
and asks for a number.
For example, say: ªfive five five one
two one two.º See ªHow to say num-
bersº earlier in this section for more
information.
The system repeats the number and
prompts you for the next command. When
you have finished entering numbers,
choose ªStore.º
4-38 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

The system confirms the name, location
and number. The system then asks if you
would like to store another location for
the same name. If you do not wish to
store another location, the system ends
the VR session.
ªEditº
q B
Use the Edit command to alter an existing
phone book entry or to add a 2nd, 3rd or
4th phone number to an existing entry.
When prompted by the system, say the
name of the entry you wish to edit.
The system acknowledges the name and
asks you for the location you would like
to edit.
Say the name of the location. The system
acknowledges and asks you for the phone
number you would like to store with this
location.
See ªHow to say numbersº earlier in this
section for more information.
The system repeats the number and
prompts you for the next command. When
you have finished entering numbers,
choose ªStore.º
The system confirms the name, location
and number, then announces that the en- try has been stored. The system then
ends the VR session.
ªDeleteº
q C
Use the Delete command to erase one en-
try from the phone book, all entries from
the phone book, the current redial
number or the current call back number.
To delete entries from the phone book,
say a name or ªAll entriesº when
prompted by the system.
The system acknowledges the command
and asks you to confirm the deletion.
To delete the current redial number or call
back number, say ªredial numberº or ªcall
back numberº when prompted by the sys-
tem.
If a redial number or a call back number
exists, the system deletes them without
asking for confirmation.
If there is no number for the entry you are
trying to delete, the system says so and
ends the VR session.
ªList namesº
q D
Use the List Names command to hear all
the names and locations in the phone
book. The system recites the phone book en-
tries but does not include the actual
phone numbers. When the playback of
the list is complete the system ends the
VR session.
You can stop the playback of the list at
any time by pressing the button on
the steering wheel. The system ends the
VR session.
ªMemo padº
The Memo Pad records a maximum of 3
voice memos, each up to 20 seconds
long.
ªPlayº
q A
The system plays back all the memos in
the order of newest to oldest. The system
ends the VR session.
If there are no memos recorded, the
system announces ªNo messages to
play.º The system ends the VR session.
Display screen, heater, air conditioner and audio systems
4-39
w 06.1.4/V35-D/V5.0
X

ªRecordº
q B
The system announces ªRecordingº and a
tone sounds signaling you to begin.
Speak the information you wish to record
clearly. When you are done, press the
or button on the steering
wheel.
A tone sounds and the system announces
ªMemo recorded.º Another tone sounds
to end the VR session.
If the memo pad is full, the system asks if
you wish to record over the oldest memo.
ªDeleteº
q C
The Delete command erases all memos.
The system asks you to confirm this ac-
tion before deleting all memos. ªSetupº
Use the Setup command to change op-
tions associated with the Bluetooth
Hands-Free Phone System.
ªPair phoneº
q A
Use the Pair Phone command to pair a
phone to the Bluetooth Hands-Free
Phone System.
When you are asked to enter a PIN code for
pairing your Bluetooth cellular phone, op-
erate it to enter the code ª1234º.
The code is always ª1234º regardless of
the number of phones paired.
Up to 5 phones can be paired. If you try to
pair a sixth phone, the system announces that you must first delete one phone or
replace an existing phone.
If you try to pair a phone that has already
been paired to your vehicle's system, the
system announces the name the phone is
already using. The pairing procedure will
then be cancelled.
When prompted by the system, choose
from the following commands:
O ªNew phoneº Ð Refer to ªPairing a
phoneº earlier in this section.
O ªReplace phoneº Ð The system an-
nounces the names of the phones al-
ready paired and asks which you
would like to replace.
Once you say the name of the phone
you wish to replace, the paring proce-
dure will begin. Refer to ªPairing pro-
cedureº earlier in this section.
O ªList phoneº Ð See the description
below.
ªList phonesº
q B
Use the List Phone command to hear the
names of the phones currently paired. If
no phones are paired, the system an-
nounces, ªNo paired phones to list.º The
system then ends the VR session.
4-40 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

ªSelect phoneº
q C
Use the Select Phone command to select
a phone of lesser priority when two or
more phones paired with Bluetooth
Hands-Free Phone System are in the ve-
hicle at the same time.
The system asks you to name the phone
and confirm the selection.
Once the selection is confirmed, the se-
lected phone remains active until the igni-
tion switch is turned OFF or you select a
new phone.
ªChange priorityº
q D
Use the Change Priority command to
change the priority level of the active
phone.
The priority level determines which phone
is active when more than one paired
Bluetooth phone is in the vehicle.
The system states the priority level of the
active phone and asks for a new priority
level (1, 2, 3, 4, 5).
If the new priority level is already being
used for another phone, the two phones
will swap priority levels. For example, if the current priority levels
are:
Priority Level 1 = Phone A
Priority Level 2 = Phone B
Priority Level 3 = Phone C
and you change the priority level of Phone
C to Level 1, then:
Priority Level 1 = Phone C
Priority Level 2 = Phone B
Priority Level 3 = Phone A
ªDelete phoneº
q E
Use the Delete Phone command to delete
a specific phone or all phones from the
Bluetooth Hands-Free Phone System.
The system announces the names of the
phones already paired with the system and
their priority level. The system then gives
you the option to delete a specific phone,
all phones or listen to the list again.
Once you chose to delete a phone or all
phones, the system asks you to confirm
this action.
NOTE:
When you delete a phone, the associated
phone book for that phone will also be de-
leted. ªSelect ringtoneº
q F
Use the Select Ringtone command to se-
lect the tone heard in the vehicle when an
incoming call is received.
The system announces the name of the
active phone and asks you to choose from
the following commands:
O ªRingtoneº Ð The system plays a ring-
tone and asks if you would like to se-
lect that tone. If you say no, the
system plays the next ringtone avail-
able and continues to cycle through
the ringtones until you select one or
quit.
O ªSilentº Ð The system asks you to
confirm your wish to disable the ring-
tone.
ªBluetooth offº
q G
Use the Bluetooth Off command to turn
off the Bluetooth Hands-Free Phone Sys-
tem.
When Bluetooth Hands-Free Phone
System is off, you will not be able to
make or receive calls using INFINITI Voice
Recognition. Also, you will not have ac-
cess to the Phone Book.
Display screen, heater, air conditioner and audio systems
4-41
w 06.1.4/V35-D/V5.0
X

You can still use the Memo Pad and ac-
cess Setup.
To turn on the system again, choose the
Bluetooth On command from the Setup
command.
SPEAKER ADAPTATION (SA) MODE Speaker Adaptation allows up to two out-of
dialect users to train the system to improve
recognition accuracy. By repeating a
number of commands, the users can create
a voice model of their own voice that is
stored in the system. The system is ca-
pable of storing a different speaker adapta-
tion model for memory A and memory B.
If memory A is available, the system will
use memory A to store the model. If
memory A is in use and memory B is
available, the system will use memory B
to store the model. If both of the memory
locations are in use, the system will ask
the user to select which memory location
should be overwritten.
Training procedure The procedure for training a voice is as
follows.
1. Position the vehicle in a reasonably
quiet outdoor location. 2. Sit in the driver's seat with the engine
running, the parking brake on, and the
transmission in Park.
3. Press and hold the button for
more than 5 seconds.
4. The system announces: ªPress the
PHONE/SEND ( ) button for the
hands-free phone system to enter the
speaker adaptation mode or press the
PHONE/END ( ) button to select a
different language.º
5. Press the button.
For information on selecting a dif-
ferent language, see ªChoosing a lan-
guageº earlier in this section.
6. Voice memory A or memory B is se-
lected automatically. If both memory
locations are already in use, the
system will prompt you to overwrite
one. Follow the instructions provided
by the system.
7. When preparation is complete and you
are ready to begin, the press the
button.
8. The SA mode will be explained. Follow
the instructions provided by the
system. 9. When training is finished, the system
will tell you an adequate number of
phrases have been recorded.
10. The system will ask you to say your
name. Follow the instructions to regis-
ter your name.
11. The system will announce that
speaker adaptation has been com-
pleted and the system is ready.
The SA mode will stop if:
O The button is pressed for more
than 5 seconds in SA mode.
O The vehicle is driven during SA mode.
O The ignition switch is turned to the
OFF or LOCK position.
Training phrases During the SA mode, the system instructs
you to say the following phrases.
(The system will prompt you for each
phrase.)
O phone book new entry
O dial three oh four two nine
O delete call back number
O setup pair phone
4-42 Display screen, heater, air conditioner and audio systems
w 06.1.13/V35-D/V5.0
X

O memo pad play
O eight pause nine three two pause
seven
O delete all entries
O call seven two four zero nine
O phone book delete entry
O memo pad record
O dial star two one seven oh
O Yes
O No
O select ring tone
O dial eight five six nine two
O Bluetooth on
O setup change priority
O call three one nine oh two
O nine seven pause pause three oh eight
O Cancel
O call back number
O call star two zero nine five
O delete phone
O dial eight three zero five one O Home
O four three pause two nine pause zero
O delete redial number
O phone book list names
O call eight oh five four one
O Correction
O setup change ring tone
O dial seven four oh one eight
O setup main menu
O Delete
O dial nine seven two six six
O memo pad delete
O call seven six three oh one
O go back
O call five six two eight zero
O dial six six four three seven
Display screen, heater, air conditioner and audio systems
4-43
w 06.1.13/V35-D/V5.0
X

TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solu-
tions.
Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom Solution
System fails to interpret the command cor-
rectly. 1. Ensure that the command is valid. See ªList of voice commandsº earlier in this section.
2. Ensure that the command is spoken after the tone.
3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the ve-
hicle.
4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster on). NOTE: If it is
too noisy to use the phone, it is likely that the voice commands will not be recognized.
5. If more than one command was said at a time, try saying the commands separately.
6. If the system consistently fails to recognize commands, the voice training procedure should be carried out to
improve the recognition response for the speaker. See ªSpeaker adaptation (SA) modeº earlier in this section.
The system consistently selects the wrong en-
try from the phone book. 1. Ensure that the phone book entry name requested matches what was originally stored. This can be confirmed
by using the ªList Namesº command. See ªPhone bookº earlier in this section.
2. Replace one of the names being confused with a new name.
4-44 Display screen, heater, air conditioner and audio systems
w 06.1.13/V35-D/V5.0
X