2006 INFINITI FX35 electrical

ELECTRICAL COMPONENT INSPECTION ACS-73
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2006 December 2006 FX35/FX45
ELECTRICAL COMPONENT INSPECTIONPFP:00000
ICC Steering SwitchNKS003FZ
1. Disconnect ICC steering switch.
2. Check resistance between ICC steering switch connector termi- nals by pressing each switch.
Booster SolenoidNKS003G1
Disconnect booster solenoid/release switch connector, and measure
resistance between terminals 4 and 6.
Release SwitchNKS003G2
Disconnect booster solenoid/release switch connector and check
resistance between the terminals.
NOTE:
If pedal is depressed insufficiently, resistance value may remain unchanged. Terminals Switch Condition Resistance [k
Ω]
14 15 MAIN
Pressed Approx. 0
Released Approx. 5.5
CANCEL Pressed Approx. 0.3
Released Approx. 5.5
DISTANCE Pressed Approx. 0.7
Released Approx. 5.5
SET/COAST Pressed Approx. 1.4
Released Approx. 5.5
RESUME/ACCELERATE Pressed Approx. 2.6
Released Approx. 5.5
PKIB4169E
Terminals Resistance [ Ω]
4 6 Approx. 1.4
PKIC5181E
Condition 1 - 3 1 - 2 2 - 3
Release
the brake pedal. Continuity should
exist. Continuity should
not exist. Continuity should
not exist.
Depress
the brake pedal. Continuity should
not exist. (Note) Continuity should
exist. (Note) Continuity should
not exist.
SKIA1256E

ACS-74
[ICC]
ELECTRICAL COMPONENT INSPECTION
Revision: 2006 December 2006 FX35/FX45
ICC Brake Switch and Stop Lamp SwitchNKS003G0
Check each switch after adjusting brake pedal, refer to BR-6,
"BRAKE PEDAL" .
ICC Brake Hold RelayNKS003IE
Disconnect ICC brake hold relay, and check continuity between ter-
minals.
Condition Continuity
ICC brake switch Stop lamp switch
When brake pedal is depressed No Yes
When brake pedal is released Yes No
SKIA5984E
Terminals Condition Continuity
34 Applying battery voltage to
between terminals 1 and 2. No
67 Yes
34 No battery voltage Ye s
67 No
PKIC4924E

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D E
F
G H
I
J
K L
M
SECTION AT
A
B
AT
Revision: 2006 December 2006 FX35/FX45
AUTOMATIC TRANSMISSION
INDEX FOR DTC ................................................... ..... 5
Alphabetical Index ............................................... ..... 5
DTC No. Index .................................................... ..... 6
PRECAUTIONS ..................................................... ..... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine ............................................... ..... 7
Precautions ......................................................... ..... 8
Service Notice or Precautions ............................. ..... 9
PREPARATION ...................................................... ... 10
Special Service Tools .......................................... ... 10
Commercial Service Tools ................................... .... 11
A/T FLUID .............................................................. ... 12
Changing A/T Fluid ............................................. ... 12
Checking A/T Fluid .............................................. ... 13
A/T Fluid Cooler Cleaning ................................... ... 15
A/T CONTROL SYSTEM ....................................... ... 18
Cross-sectional View (2WD Models) ................... ... 18
Cross-sectional View (VQ35DE Models for AWD) ... 19
Cross-sectional View (VK45DE Models for AWD) ... 20
Shift Mechanism .................................................. ... 21
TCM Function ...................................................... ... 32
CAN Communication ........................................... ... 33
Input/Output Signal of TCM ................................. ... 33
Line Pressure Control ......................................... ... 34
Shift Control ........................................................ ... 35
Lock-up Control ................................................... ... 37
Engine Brake Control .......................................... ... 38
Control Valve ....................................................... ... 38
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 40
Introduction ......................................................... ... 40
OBD-II Function for A/T System .......................... ... 40
One or Two Trip Detection Logic of OBD-II ......... ... 40
OBD-II Diagnostic Trouble Code (DTC) .............. ... 40
Malfunction Indicator Lamp (MIL) ........................ ... 43
TROUBLE DIAGNOSIS ......................................... ... 44
DTC Inspection Priority Chart ............................. ... 44
Fail-safe .............................................................. ... 44 How to Perform Trouble Diagnosis for Quick and
Accurate Repair ................................................... ... 46
A/T Electrical Parts Location ............................... ... 51
Circuit Diagram .................................................... ... 52
Inspections Before Trouble Diagnosis ................. ... 53
Check Before Engine Is Started .......................... ... 57
Check at Idle ........................................................ ... 57
Cruise Test - Part 1 .............................................. ... 58
Cruise Test - Part 2 .............................................. ... 60
Cruise Test - Part 3 .............................................. ... 61
Vehicle Speed at Which Gear Shifting Occurs .... ... 62
Vehicle Speed at Which Lock-up Occurs/Releases ... 63
Symptom Chart .................................................... ... 64
TCM Input/Output Signal Reference Values ........ ... 89
CONSULT-II Function (A/T) ................................. ... 90
Diagnostic Procedure without CONSULT-II ......... .102
DTC U1000 CAN COMMUNICATION LINE ........... .104
Description ........................................................... .104
On Board Diagnosis Logic ................................... .104
Possible Cause .................................................... .104
DTC Confirmation Procedure .............................. .104
Wiring Diagram — AT — CAN ............................. .105
Diagnostic Procedure .......................................... .106
DTC P0615 START SIGNAL CIRCUIT .................. .107
Description ........................................................... .107
CONSULT-II Reference Value ............................. .107
On Board Diagnosis Logic ................................... .107
Possible Cause .................................................... .107
DTC Confirmation Procedure .............................. .107
Wiring Diagram — AT — STSIG ......................... .108
Diagnostic Procedure .......................................... .109
DTC P0700 TCM .................................................... .. 111
Description ........................................................... ..111
On Board Diagnosis Logic ................................... ..111
Possible Cause .................................................... ..111
DTC Confirmation Procedure .............................. ..111
Diagnostic Procedure .......................................... ..111
DTC P0705 PARK/NEUTRAL POSITION SWITCH .112
Description ........................................................... .112
CONSULT-II Reference Value ............................. .112

AT-4Revision: 2006 December 2006 FX35/FX45 A/T Does Not Shift: 5th Gear
→ 4th Gear ........... .219
A/T Does Not Shift: 4th Gear → 3rd Gear ........... .221
A/T Does Not Shift: 3rd Gear → 2nd Gear .......... .223
A/T Does Not Shift: 2nd Gear → 1st Gear ........... .225
Vehicle Does Not Decelerate by Engine Brake ... .227
SHIFT CONTROL SYSTEM ................................... .229
Control Device Removal and Installation ............. .229
Control Rod Removal and Installation ................. .230
Adjustment of A/T Position .................................. .231
Checking of A/T Position ..................................... .231
A/T SHIFT LOCK SYSTEM .................................... .232
Description ........................................................... .232
Shift Lock System Electrical Parts Location ........ .232
Wiring Diagram — AT — SHIFT .......................... .233
Diagnostic Procedure .......................................... .234
KEY INTERLOCK CABLE ..................................... .236
Components ........................................................ .236
Removal and Installation ..................................... .237
ON-VEHICLE SERVICE ......................................... .239
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .239
Parking Components (2WD Models Only) ........... .251
Rear Oil Seal ....................................................... .258
Revolution Sensor Components (2WD Models
Only) .................................................................... .259
AIR BREATHER HOSE .......................................... .264
Removal and Installation ..................................... .264
TRANSMISSION ASSEMBLY ............................... .266
Removal and Installation (2WD Models) ............. .266
Removal and Installation (AWD Models) ............. .269 OVERHAUL ............................................................
.274
Components ......................................................... .274
Oil Channel .......................................................... .288
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .291
DISASSEMBLY ...................................................... .294
Disassembly ......................................................... .294
REPAIR FOR COMPONENT PARTS ..................... .312
Oil Pump .............................................................. .312
Front Sun Gear, 3rd One-way Clutch ................... .315
Front Carrier, Input Clutch, Rear Internal Gear .... .317
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .323
High and Low Reverse Clutch ............................. .329
Direct Clutch ........................................................ .332
ASSEMBLY ............................................................ .335
Assembly (1) ........................................................ .335
Adjustment ........................................................... .349
Assembly (2) ........................................................ .352
SERVICE DATA AND SPECIFICATIONS (SDS) ... .359
General Specifications ......................................... .359
Vehicle Speed at Which Gear Shifting Occurs ..... .359
Vehicle Speed at Which Lock-up Occurs/Releases .360
Stall Speed ........................................................... .360
Line Pressure ....................................................... .360
A/T Fluid Temperature Sensor ............................. .360
Turbine Revolution Sensor ................................... .361
Vehicle Speed Sensor A/T (Revolution Sensor) .. .361
Reverse Brake ..................................................... .361
Total End Play ...................................................... .361

PRECAUTIONS AT-7
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NCS001AN
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineNCS001AO
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative termi-
nal before any repair or inspection work. The open/short circuit of related switches, sensors, sole-
noid valves, etc. Will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. May cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EVAP system or fuel injection system,
etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-44
TROUBLE DIAGNOSIS
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSISPFP:00004
DTC Inspection Priority ChartNCS001BC
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000 CAN
COMMUNICATION. Refer to AT- 1 0 4
.
Fail-safeNCS001BD
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is a an error in
a main electronic control input/output signal circuit.
In fail-safe mode, even if the selector lever is “D” or “M” mode, the transmission is fixed in 2nd, 4th or 5th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration”.
Even when the electronic circuits are normal, under special conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the tire rotation), the transmission can go into fail-safe
mode. If this happens, switch OFF the ignition switch for 10 seconds, then switch it ON again to return to the
normal shift pattern. Therefore, the customer's vehicle has returned to normal, so handle according to the
“WORK FLOW” (Refer to AT- 4 7
).
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the A/T to mark driving possible.
Vehicle Speed Sensor
Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the trans-
mission and from combination meter so normal driving is possible even if there is a malfunction in one of the
systems. And if vehicle speed sensor A/T (revolution sensor) has unusual cases, 5th gear and manual mode
are prohibited.
Accelerator Pedal Position Sensor
If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow systems,
the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor
If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow systems,
the accelerator opening angle is controlled by the idle signal sent from the ECM which is based on input indi-
cating either idle condition or off-idle condition (pre-determined accelerator opening) in order to make driving
possible.
PNP Switch
In the unlikely event that a malfunction signal enters the TCM, the position indicator is switched OFF, the
starter relay is switched OFF (starter starting is disabled), the back-up lamp relay switched OFF (back-up lamp
is OFF) and the position is fixed to the “D” position to make driving possible.
Starter Relay
The starter relay is switched OFF. (Starter starting is disabled.)
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

TROUBLE DIAGNOSIS AT-45
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
A/T Interlock

If there is an A/T interlock judgment malfunction, the A/T is fixed in 2nd gear to make driving possible.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.

When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is per-
formed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG X: OK
A/T 1st Engine Braking
When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is switched
OFF to avoid the engine brake operation.
Line Pressure Solenoid
The solenoid is switched OFF and the line pressure is set to the maximum hydraulic pressure to make driving
possible.
Torque Converter Clutch Solenoid
The solenoid is switched OFF to release the lock-up.
Low Coast Brake Solenoid
When a (electrical or functional) malfunction occurs, in order to make driving possible, if the solenoid is ON,
the transmission is held in 2nd gear; if the solenoid is OFF, the A/T is held in 4th gear. (Engine brake is not
applied in 1st and 2nd gear.)
Input Clutch Solenoid
If a (electrical or functional) malfunction occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Direct Clutch Solenoid
If a (electrical or functional) malfunction occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Front Brake Solenoid
If a (electrical or functional) malfunction occurs with the solenoid ON, in order to make driving possible, the A/
T is held in 5th gear; if the solenoid is OFF, 4th gear.
High and Low Reverse Clutch Solenoid
If a (electrical or functional) malfunction occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Turbine Revolution Sensor 1 or 2
The control is the same as if there were no turbine revolution sensors, 5th gear and manual mode are prohib-
ited.
Gear position ATF pressure switch output
Fail-safe function Clutch pressure output pattern after fail-safe func-
tion
SW3 (I/C) SW6
(HLR/
C) SW5
(D/C) SW1
(FR/B) SW2
(LC/B) I/C HLR/C D/C FR/B LC/B L/U
A/T inter-
lock cou-
pling pattern 3rd – X X –

Held in
2nd gear OFF OFF ON OFF OFF OFF
4th – X X –
Held in
2nd gear OFF OFF ON OFF OFF OFF
5th X X – X
Held in
2nd gear OFF OFF ON OFF OFF OFF

TROUBLE DIAGNOSIS AT-51
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
A/T Electrical Parts LocationNCS001BF
SCIA7752E