BE-52Body Electric SystemCentral Control Lock and Electric Rocker Gear System
Definition for connecting wire of central control lock
1. Y/V Connect the power to the cell anode on vehicle, in front of which a fuse of 15 A should be set, and
anode of 12V when the motor is started, the voltage should not less than 10V
2. B1 Unlocking output of the locking wire of the CCL actuator, and the grounding wire at the normally
central control lock: closed contact inside the relay will contact with the normally opening contact at
the common spots inside relay when unlocking with REMOTE CONTROLLER
or manually, the wire will output 12 V voltage.
3. LG locking signal of The CCL locking signal is connected to the unlocking wire of actuator of CCL,
central control lockand the normally closed contact in the interior relay is grounding wire, which will
output 12 V voltage when unlocking with REMOTE CONTROLLER or manually
and the common spots of relay contacting the normally opening contact.
4. non-connection There is no wire connected at present
5. G/R Right turn lampConnected to the anode wire of the right turn lamp on the vehicle, and it will output
12 V voltage in operation.
6. G/Y Left turn lamp Connected to the anode wire of left turn lamp on the vehicle, and it will output
12 V voltage when in operation
7. Br Negative input ofWhich is connected to the door switch and it is grounding when the door is
door switch opened (the indoor lamp will light)
8. GD ON power check cable Connected to the ON wire of the locking door( there will be 12 v voltage when
rotating the key at ON position.
9. Non-connection This wire is not connected temporarily
10. GD/B Lock head lamp outputThere will be 12 V voltage outputted in this wire when opening the door, and will
be powered off (no output) ten seconds later after the door is closed
12. Y/B Locking signal Connected to the locking signal wire of CCL at the left front door, and connect
to the grounding wire when in operation.
13. B Power cathode Connect to the body (grounding wire) it should be as short as possible, because
the overlong wire will produce the interference source. SF
13P
1
2
3
4
5
6
7
8
9
10
11
12
13Power anode 12 V
unlocking signal of central control lock
locking signal of central control lock
no signal
right turn lamp
left turn lamp
negative input of door switch
ON power check cable
no connection
lock head lamp
unlocking signal
locking signal
power cathode
MK
Remark: the inner switch in actuator should be
connected when the actuator is in the locking status
Remark: In case the actuator is in locking status,
connect the switch inside.
ON wire connected to key
hNOs
hj
left front CCL switch
1 2 3 4 5 6
7 8 9 10 11 12 13
BE-55 Body Electric SystemCCL and Electric Rocker Gear System
Definition of the connecting wire of CCL
1. G/R (G/W) Turn lampConnected to the anode wire of the turn lamp (right ) on vehicle, it will output 12 V voltage
when it is in operation
2. Ow/b1)Window-shutting signal outputThis wire has one second of voltage output of 12V when the car door is locking. (top SY SJ)
3. No connection
4. G (Y) Unlocking output of CCLConnected to the locking wire of actuator of CCL, and the normally closed contact in the
internal relay is the grounding wire.It will output 12 v voltage when locking with REMOTE
CONTROLLER or manually because the common spot of relay will contact the normally
opening contact.
5. Bl (G) Locking output of CCLConnected to the locking wire of actuator of CCL, and the normally closed contact inside
the internal relay is the grounding wire.It will output 12 V voltage when locking with
REMOTE CONTROLLER or manually because the common sots of relay will contact
with the normally opening contact.
6. Gr (G/B) Turn lampConnected to the anode wire of left turn lamp of vehicle, it will output 12 v Voltage when in
operation.
7. W (W) Manually controlled unlocking signalThe door lock control the locking process through the manual unlocking switch at left front
door, that is, under the locking condition, press the switch, the lock will be opened (the
switch will return to the connection situation automatically after pressing.
8. Br (R/B) Negative output of door switchConnected to the car door lamp switch, it is connected to the grounding wire (the indoor
lamp will light when opening the door.
9. R/G (G/B) Rotating speed testThe car door will lock automatically when the vehicle reaches a certain speed.
10. W(R ) ACC testConnect to the ACC wire, which will have 12 V voltage when the key is rotated to the ACC position.
11. R (R ) Power anode (12V)Connect to the anode of accumulator on vehicle, in front of which should be set the fuse
so that the voltage will be no less than 10V when the starter is in operation.
12. B(B) Power cathodeConnect to the body (grounding wire), it should be short as possible as can because the
overlong wire will produce the interference source.
SY SJ
1
2
3
4
5 6
7
8
9
10
11
12left turning light
manual switch locking signal
closing window output
none
door switch negative input
speed test
ACC test
power anode 12V
remote control opening lock output
power cathode
remote control closing lock output12V
W
K door switchK
M
M
MM
Items in the parenthesis is for SY diesel model
Items with are configuration for SJ and top SY