2006 GREAT WALL PEGASUS clock

TF-18
1. deceleration gear
2. output shaft
3. insert face of toggle fork
4. deceleration toggle fork assembly
5. pin, contact roller and sleeve assembly
6. deceleration shift toggle fork
7. plastic sleeve
8. contact roller
9. pin
12
6
7
8
9 3
NO PQ
R
S T
Transfer Box
Transfer Box Assembly
7. Deceleration shift parts assembly
The mounting process is as follows:
(a) If the parts are taken apart for change, assemble the shift
toggle fork assembly with a new pin-contact roller
assembly. Press the pin-contact roller in the deceleration
fork hole until the detent passes the hole completely and
seizes the right location. Ensure that the contact roller can
run freely.
(b) Mount two inserted faces of toggle fork on the decelera-
tion toggle fork assembly.
(c) Engage the deceleration fork assembly and deceleration
gear sleeve and put them in the housing, and the decelera-
tion gear sleeve shall be put in the planetary mechanism
assembly that is assembled already. Mount the rear
output shaft and joint the bearings at the ends of output
shaft and input shaft as well as the spline of the gear
sleeve.
Remarks: the output shaft assembly can be delayed until the oil
pump is mounted on the output shaft. The oil pump may be
dipped into the lubricant through the oil pump screen, turn the
output shaft in clockwise from the output shaft direction to see
whether there is lubricant pumped out so as to check whether
the oil pump can work normally or not. The parts mounted
readily may be encased in the transfer box housing as an
assembly
8. Oil pump assembly
Ensure the parts of oil pump are completely lubricated when
assembling, and the oil can be pumped out from the conical
hole of the oil pump front cover. The mount of oil pump is as
follows:
(a) Mount the pin on the rear output shaft.
(b) Slide the oil pump assembly on the rear output shaft
along with the pin.
(c) Put the gripping hoop at the end of oil pipe that is
mounted on the oil nozzle of the pump housing, screw up
the gripping hoop.
1. filter
2. oil pump hose
3. gripping hoop
4. oil pump assembly
5. output shaft
6. pump pin
7. output shaft and pump assembly5
4

TF-22
12
3 4
6
7
8
95
21
Transfer Box
Transfer Box Assembly
1. motor assembly
2. shift shaft
1. fixed sensor bracket
2. bolt
3. sensor assembly
4. velocity sensor
5. o-ring6. motor assembly
7. bolt
8. gasket
9. transfer box rear body
12. Mount the external electric shifting element (for the elec-
tric shift transfer box)
(a) Locate the motor assembly by aligning the triangle
groove on motor to the shift shaft.
(b) Move the motor to combine the shift shaft and keep it
close to the rear cover. Then run the motor clockwise
until the motor locates the correct place and the mooting
holes are aligned.
(c) Mount the O-ring on the velocity sensor and encase the
velocity sensor assembly in rear cover. A clip and three
bolts shall be mounted on the velocity sensor.
Fastening torque
(8
11)N
m
(d) Mount the bolts and gaskets on the end of motor clip.
Fastening torque
(8
11)N
m

SR-3Steering System
On-vehicle Inspection
max play
On-vehicle Inspection
Steering wheel play
1.SR-18Check to see whether the steering wheel play is
correct;
Park the vehicle stably and align the tires in correct direction,
press the steering wheel with finger and swing it in left and
right direction. The play should not exceed the max play.
(Max play)
6
(Dr SF)
If the play is nor correct, adjust or repair the steering wheel as
requirement.
2. Adjust the steering wheel play:
(a) Align the wheel forward precisely;
(b) Loosen the locking nuts of steering gear;
(c) Rotate the adjusting screws of steering gear clockwise to
reduce the steering wheel play, while contrarotate the
adjusting screws to increase the steering wheel play.
Remark: screw the adjusting screws and enlarge the play a
little each time to check the adjusted play.
3. Check to see whether there is steering inconvenience
Rotate the steering wheel by half round in right and left
direction to check whether the play is correct, and whether the
wheel runs smoothly or any seize-up in its running.
4. Fix the adjusting screws and fasten the adjustable nut.
Oil level height
Check the oil level height in the steering gear housing.
Oil level height: flush with the filler opening.
If there oil is insufficient, add the gear oil and check to see
whether there is oil leakage.

BE-33Body Electric System
Combination Instrument
Electric circuit diagram (continued)
SF
A3 connected
with negative pole
A1 connected
with positive pole
B8 connected
with negative
pole
B7connected
with positive
pole
A4 connecting
with lighting
switch
A6 connected
with negative
pole
pressure-regulating
potential deviceirect-current
power supply
5-9Vdrive power
supply
110VEL
luminous
plate
left turn indicating lamp
right turn indicating lamp
upper beam indicating lamp
rear fog lamp indicating lamp
rear window/defroster indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
connected with sensor
connected with revolution signal
speedometer
digital clock
fuel gaugeconnect to the cathode of sensor
connected with sensor anode
connected with sensor
connected with sensor
back door indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp75
B9
B2 A15 B1 A9 B11 B10
A14 B4 B6 A12
B14 connected
with positive
pole
B7 connected
with positive
pole
A11 A5A7 B12B5 B13 A16A13 B16 B15
A2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
In this drawing, A stands for the white plugging
elements, B for black plugging elements, they
use the same numerical order.
instrument
plugging element