2006 GREAT WALL PEGASUS gearbox

TF-7Transfer Box
Disassembly and Mount of Transfer Box
Disassembly and Mount of Transfer Box
1. Transfer Box Disassembly
(a) Drive the vehicle on the lifting jack.
(b) Locate the gear of transfer box at the neutral
position, shift the transfer box to the 2H and
extinguish the engine.
(c) Disconnect the cell cathode.
(d) Lift the vehicle.
(e) Put down an oil disc under the transfer box, tear
down the oil drain plug and oil filling plug of the
transfer to drain all the lubricant up, then re-
mount the two plugs.
(f) Disconnect all wires and wire harnesses that
connected with the transfer box.
(g) Take apart the hose on the venting valve of
transfer shaft.
(h) Disconnect the linkage of the front drive shaft
with the front flange of the transfer box.
(i) Disconnect the linkage of the rear drive shaft
with the rear flange of the transfer box.
(j) Raise the transfer box up with the jack.Notice: The transfer box shall be guaranteed to
support by the lifting jack before tearing down
the sets of bolt and nut that connected with the
transfer box and gearbox. The transfer box is
not allowed to hang directly on the gearbox
through spline because such operation will
damage the transfer box parts.
(l) Tear down the connecting nuts between the
transfer box and gearbox and take down the
transfer box.
(m) Move the transfer box backward directly until
the linkage between the input shaft of transfer
box and the gearbox spline.
(n) Put down the lifting jack of the transfer box, and
(o) Tear down the gasket between the transfer box
and gearbox. Clean the gasket or glue on the
coupling face of front body of transfer box with
rear body of the gearbox. Take notice not to
damage the coupling face.
1234
5 6 7
8
9
1. input shaft
2. front frame of transfer box
3. rear cover of transfer box
4. flange
5. front output fork flange
6. venting valve
7. gasket
8. rear body of gearbox
9. bolt

TF-8Transfer Box
Disassembly and Mount of Transfer Box
2. Transfer box mount
a) Coat the lubricant grease on the output axial
spline of the gearbox with a thin sleeve contain-
ing lubricant grease.
b) Mount a new gasket on the mounting face of the
transfer box.
c) Lift the lifting bracket of transfer box and align
it to the same axle with the gearbox.
Notice: The transfer shall be guaranteed to flush
with the gearbox before connecting the spline.
Do not handle it forcefully to press the transfer
box spline into the gearbox. Otherwise, damage
will be caused, run the rear output shaft where
necessary to aim at the spline.
(d) Move the transfer box forward slowly so that
the spline and pin of the input shaft of gearbox
reach the front body of the transfer box, and the
gasket attaches on the gearbox completely.
(e) Ensure that the mounting holes of the front
body of transfer box, gasket, and gearbox are in
alignment and then mount the sets of bolt and
nut.
Fastening torque
(35-48)N
m
(f) Connect the rear drive shaft and the rear output
flange of the transfer box.
(g) Connect the front drive shaft and the front
output fork flange of the transfer box.(h) Connect the venting valve and the soft ventila-
tion pipe.
(i) Connect the cables of odometer that locates
nearby the transfer box.
(j) Connect all wire harnesses that connected with
the transfer box, and
(k) Add the lubricant of right brand.
Notice: when starting the engine, if the lubricant
is added incorrectly or in unsuitable volume,
which may lead the transfer box to damage.
Notice: as for the transfer box mounted on
vehicle, oil pump shall be used when adding oil
for it.
Notice: In case the transfer box is taken apart for
maintenance or inspection, there will be no
lubricant supplied by oil pump in the oil passage
on the top of transfer box. Therefore, it is not
accurate to control the oil volume by opening the
oil filling plug, in such condition, the oil passage
will be filled with oil once the oil pump runs. If the
wheel can run, such operation can be conducted
on the lifting jack. The oil level shall be rechecked
once the oil pump runs.
(l) Put down the vehicle after finishing the lubri-
cant inspection, and connect the cell cathode.

PR-5Drive Shaft
Drive Shaft
(4WD)
Rear axle drive shaft
1. Take apart the universal joint flange fork of rear axle drive
shaft from the differential flange.
(a) Label the two flanges with assembly marks.
(b) Take apart the four sets of bolt and nut.
Disassembly of Drive Shaft
(2WD)
1. Take apart the universal joint flange fork of the drive shaft
from the differential flange.
(a) Label the two flanges with assembly remarks.
(b) Take apart the four sets of bolt and nut.
assembly mark
2. Take apart the center support bearing from the frame
beam (for the three-joint type)
3. Take apart the drive shaft from the gearbox
(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox for oil leakage prevention.
2. Take apart the center support bearing from the frame
beam (three-joint type
SST
assembly mark

PR-6Drive Shaft
Drive Shaft
3. Take apart the drive shaft from the gearbox.
(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox to prevent the oil leakage
Front axle drive shaft
4. Tear down the front universal joint flange fork of the front
drive shaft.
(a) Hang he front end of the front axle drive shaft.
(b) Label the assembly mark on the flange
(c) Take apart the four sets of bolt and nut.
5. Disconnect the rear universal joint flange fork from the
front axel drive shaft along the transmission path.
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
Drive shaft disassembly
1. Separation of the rear joint of the rear axle drive shaft
from the front joint of rear axle drive shaft
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
2. Take apart the center support bearing from the front joint
of the rear axle drive shaft.
(a) Loosen the riveted nut by chiseling with a chisel and
hammer.
SST
assembly mark
assembly mark

PR-12Drive Shaft
Drive Shaft
Mount of Drive Shaft
(2WD)
1. Insert the universal joint yoke in the gearbox.
(a) Tear down the SST tools.
(b) Push the universal joint yoke into the gearbox.
2. Connect the universal joint flange of the rear joint of rear
axle drive shaft and the relative the differential flange.
(a) Align the assembly marks on the two flanges and connect
the flanges with four sets of bolt and nut.
(b) Screw up the sets of bolt and nut according to the
specified torque.
Fastening torque
(74
5)N
m
3. Mount the center support bearing on the frame beam
(three-joint type)
(a) Use two bolts to mount the center support bearing on the
frame beam and tighten them manually.
(b) Check the bearing seat, which shall be vertical with the
drive shaft, and change it where necessary.
(c) Check the central line of the central bearing and ensure
that the central lines of the central bearing and the bear-
ing seat shall be the same when the vehicle is in the non-
loaded stage. And adjust the bearing seat only it is
necessary.
(d) Screw up the mounting bolts according to the specified
torque.
Fastening torque
(40
5)N
m
(4WD)
1. Connect the universal joint flange fork of the front axle
drive shaft with the flange that matches with the transfer
box.
Align the assembly marks and use four sets of bolt and nut to
connect the flange fork with the flange, screw up the sets of bolt
and nut according to the specified torque.
Fastening torque
(74
5)N
m
forward
SST
assembly mark
assembly mark

B0-53Vehicle Body
Instrument Panel
Dismantle of instrument panel
(Dr SF)
1. Disconnect the cable of accumulator from the negative
polar;
2. Tear down the steering wheel;
3. Tear down the combined switch shell cluster;
4. Tear down the bonnet lock switch;
Tear down the two screws and the sliding fastener of bonnet
lock.
5. Tear down the central bottom-wall (Dr)
Tear down the decorative cover of gearbox (SF)
6. Tear down the instrument cover (SF).
Tear down the two screws and the cover.
7. Tear down the lower instrument cover;
(a) Tear down the ignition lock;
(b) Tear down the five screws and the cover;
Tear down the four screws and the cover;
(c) Disconnect the plugging elements.
8. Tear down the air-conditioner controlling panel;
(a) Pull out the air-conditioner controlling button;
(b) Prize out the A/C switch;
(c) Prize out the air-conditioner panel as shown in the
drawing with screwdriver and take it down.
Notice: the screwdriver should be wrapped with adhesive
strap at its head before using.
(d) Disconnect the plugging elements.
9. Tear down the decorative cover of instrument (Dr)
(a) Tear down the two screws to pull out the decorative cover
of instrument;
(b) Disconnect the plugging elements.E
F

A-2
Clutch
Specification
Item Specification
Fastening torque for clutch tube on master cylinder
Fastening torque for clutch tube on wheel-brake cylinder
Fastening torque for clutch pressure plate160
190-200
5-15
0.3
0.8
0.2
0.6
5
Max misplacement
0.5 Pedal height (calculated from front wall
Pedal free stroke
Min depth of clutch-facing rivet
Max radial swing difference of clutch rib
Max radial swing difference of flywheel
Max width of wear of diaphragm spring
Max width of wear of diaphragm spring
Alignment degree of diaphragm spring endApplicable vehicle model
Dr SF
SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Torsion moment
Fastening location (N*m)
15-17
15-17
30 Applicable Vehicle model
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,
Lubricant Type
GL-5 SAE80W/90
Torsion moment of relative connecting elements
Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)
Unit
ãã Specification of Maintenance and Up-Keeping
Clutch and Gearbox
Locating screw of fork axle at first and second gear
Locating screw of yoke block
Screw on baffle of rear bearing of output shaft
Screw of reverse idler shaft
Bolt of gearshift cover
Bolt of front cover
Bolt of rear body
Bolt of clutch shell
Bolt of locating spring13
17
15
20
17
22
17
20
15
20
15
20
30
45
30
45
17
22 Fastening location N*m