Page 422 of 484
B0-39Vehicle BodySide Window Glass
3. Mount the trim strip and spilling strip of side window (SY SJ)
(a) Assemble the trip strip of side window on the left upper
conner of inner edge of the left side window at 60 mm under
the conner, and encase the roof in the trim strip.
(b) Stick the spilling strip (46) to the center of lower edge of
side window and to the circumference of the glass frame.
4. Mounting of side glass
Coat the cleaning active agent around the inner edge along the
circumference of side window glass (the black glass edge).
Airing for 3 to 5 min, coat the priming agent on the layer of cleaning
active agent and airing for 5 to 30 min.
(SYSJ)
(a) Plaster the glass glue with the glue container on the layer of
priming paint of window frame with the initiative location
200 mm under the left upper conner of left side window.
(b) Stick the glass quickly to the window frame and adjust the
upper, lower, left and right clearance, and fill them with
gasket.
(c) Exert the pressure of certain degree on the glass circumfer-
ence after adjusting so that the glass contact
Recommended sealing glue for use
Glass glue U-201 windshield glue
Priming paint 130
Cleaning active agent C020
(SF)
(a) Plaster the glass glue alongside the complete circumference
of adhesive strip of side window glass, and the glue section
should be similar to tri-angle after coating.
(b) Put the side window glass assembly at the corresponding
location on body, fix the upper edge of side window glass with
three hex nuts and others should be fixed with flange nuts.
Recommended sealing glue for use
Glass glue TS-100 PVC windshield glue
Priming paint TS-5028
Cleaning active agent TS-7016
Notice:
(a) When plastering glue, the glue should be plastered continu-
ously and no breakage is allowable at the sealing glue seam.
(b) Clean the redundant glue on the body;
(c) The vehicle is not allowed to drive within 4 hours in summer
and 8 hours in winder under common circumstances.
5. Check whether there is leakage and the leakage reparation;
(a) Conduct the leakage test;
(b) Seal the leaking parts with glass glue. SJ
SY
SF
Page 425 of 484
B0-42Vehicle BodyRear Windshield
Mount of rear windshield
1. Clean the body and glass;
Clean the contacting face of body and glass with the
cleaning materials.
2. Clean the sealing strip
Clean the sealing strip with cleaning materials;
4. Mount the rear windshield
(a) Lay the ready glass against the corresponding position of
rear windshield opens.
(b) Pull the rope from the inside of body to encase the roof,
the rear column and the door frame within the adhesive
strip, meanwhile push the outside of the glass by hand.
(c) Tap the four edges of the adhesive strip to ensure that the
adhesive strip contact closely with the body windshield
opened.
(d) Coat the glue from left to right at the upper part of
windshield (location between the adhesive strip and the
body windshield open) and the lower part of windshield
(location between the adhesive strip and glass), and the
remaining glue should be cleared away with abrasive
paper, and the location should be cleaned with cloth.
Notice: there should no breakage at the sealing glue
seam when coating the glue.
Recommended sealing agent for use
Glass glue XL-1211 acid silicone glass glue
5. Check whether there is leakage and the leakage
reparation;
(a) Conduct the leakage test;
(b) Seal the leaking parts with glass glue. 3. Mount the rear windshield in the sealing strip
(a) Coat a layer of silicon oil around the glass circumference
and mount the adhesive strip on the glass according to
the glass shape.
Notice: if the adhesive strip becomes stiffening or
deforming that will lead to water leakage, change with
the new one where possibly.
(b) Mount a rope alongside the sealing strip channel as
shown in the drawing (fix the rope in the adhesive strip).
Page 457 of 484
B0-74
Body Dimension
Rear Wall ()
Vehicle BodyBody Dimension
Mark NameBore diameterMark NameBore diameter
J,jConnecting part of outer panel of
rear wall with roofO,oCorresponding spots of upper edge
K,kLower edge of outer panel of rear
wallP,pVertical corresponding spot of
floor
L,lLines and angle of rear side wall
Q,q
M,mUpper angle of rear lamp cavity
R,rOuter edge of lock box at tailgate
N,nLower angle of rear lamp cavity
J
k K 1022j
1270 1202
376
SY SJ
(point size in 3D)
GN Oo
m Qq
N
n
Pp
Rr M900 L
1042
1376 1141l
*1: SY 1376
SJ 1385
SF
(point size in 3D)
