2006 FIAT STILO wheel bolts

171
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF A TYRE IS
PUNCTURED
GENERAL INSTRUCTIONS
Wheel changing and correct use of the
jack and space-saver spare wheel call for
some precautions as listed below.
IMPORTANT If the car is fitted with “Fix
& Go (quick tyre repair kit)”, see the rel-
evant instructions in the following chap-
ter.
Alert other drivers that the
car is stationary in compli-
ance with local regulations: hazard
warning lights, warning triangle, etc.
Any passengers on board should leave
the car, especially if it is heavily laden.
Passengers should stay away from on-
coming traffic while the wheel is be-
ing changed. If parked on a slope or
rough surface, chock the wheels with
wedges or other suitable devices to
prevent the car from rolling.
WARNING
The space-saver spare wheel
(where provided) is specific
to your car, do not use it on other
models, or use the spare wheel of oth-
er models on your car. The space-
saver spare wheel shall only be used
in an emergency. It shall only be used
for the distance necessary to reach a
service point and the car speed shall
not exceed 80 Km/h. The spare wheel
has an orange sticker that summaris-
es the main cautions for use and lim-
itations. The sticker should never be
removed or covered. Never fit a wheel
cap on a space-saver spare wheel.
The sticker gives the following infor-
mation in four languages: caution! For
temporary use only! 80 km/h max!
Replace by normal wheel as soon as
possible. Do not cover this label.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of the car
changes. Avoid accelerating or brak-
ing sharply, abrupt turns or fast cor-
nerings. The life of the spare wheel
is approx. 3000 Km, after this dis-
tance it should be replaced with an-
other of the same type. Never at-
tempt to fit a conventional tyre on a
rim designed for use as a space-saver
spare wheel. Have the punctured
wheel repaired and refitted as soon
as possible. Two or more space-saver
spare wheels should never be used to-
gether. Do not grease the threads of
bolts before installing them: they
might slip out.
WARNING

174
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒using the wrench provided L-fig. 6
loosen the fastening bolts by about one
turn; if the car is fitted with alloy rims,
shake the car to facilitate removing this
rim from the wheel hub;
❒work the jack crank M-fig. 7to extend
it until the groove Non the upper part
of the jack is correctly inserted on the
lower profile Pof the body in point Q
(at approx. 72 cm from the front wheel
centre or 75 cm from rear wheel cen-
tre);❒undo the wheel bolts and remove the
wheel.
❒make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not come
loose;
fig. 6F0C0394m
fig. 7F0M0395m
❒warn anybody nearby that the car is
about to be lifted. They must stay clear
and not touch the car until it is back on
the ground;
❒fit the handle R-fig. 7to operate the
jack and raise the car until the wheel
is a few centimetres from the ground;

175
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒install the space-saver spare wheel
matching the holes S-fig. 8with the
corresponding pins T;
❒using the wrench provided, fully tight-
en the four fastening bolts;
❒work the jack handle R-fig.7to lower
the car and remove the jack;
❒using the wrench provided, tighten up
the wheel bolts in a criss-cross fashion
following the sequence shown in fig. 9.REFITTING THE STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
Versions with steel rims
Proceed as follows:
❒Make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will not
come loose;
❒Fit the normal wheel matching the
holes S-fig. 8with the corresponding
pins T;
❒Using the wrench provided, tighten the
fastening bolts;
❒Lower the car and remove the jack;
❒Using the wrench provided, fully tight-
en the bolts in the sequence shown in
fig. 9;
❒Place the cap near the wheel so that the
inflation valve can come through the
slot provided on the cap;
❒Press the circumference of the cap,
starting from the parts nearest the in-
flation valve until it is inserted com-
pletely.
IMPORTANT Incorrect fitting may cause
the wheel cap to come off when the car is
travelling.
fig. 8F0C0396mfig. 9F0C0397m

176
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Versions with alloy rims
Proceed as follows:
❒Tighten the pin A-fig. 10in one of the
fastening bolt holes on the wheel hub;
❒Insert the wheel on the pin and, using
the wrench provided, tighten the four
bolts available. This is facilitated by the
extension provided B;
❒Loosen the pin Aand tighten the last
fastening bolt;
❒Lower the car and remove the jack;
❒Using the wrench provided, fully tight-
en the bolts in the sequence shown
previously for the space-saver spare
wheel (see fig. 9).When you have finished
❒Stow the space-saver spare wheel G-
fig. 11in the space provided in the
boot;
❒Insert the partially open jack into the
container Fand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ Put the tools back into their places in
the container;
❒Stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device E;
❒Correctly reposition the boot stiff cov-
er.
fig. 10F0C0217m
fig. 11F0C0392m

187
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
FRONT SIDELIGHTS
To replace the bulbs proceed as follows:
❒remove the protective cover Aand C-
fig. 27releasing catch Band Dre-
spectively;
❒using the extension A-fig. 28or D-
fig. 29, turn the bulb holder B-fig. 28
or E-fig. 29clockwise and counter-
clockwise and then withdraw it;
❒remove the bulb C-fig. 28or F-fig. 29
and replace it;
❒refit the bulb holder making sure the
catch clicks into place; also check the
proper bulb positioning looking at the
lamp from outside;
❒refit the protective cover correctly.REAR LIGHT UNITS
(saloon versions)
To change the bulb, proceed as follows:
❒open the tailgate;
❒from inside the boot, withdraw the
connector A-fig. 30, loosen the 3 nuts
Bwith the extension (where provided)
used to tighten the wheel bolts (sup-
plied with the tool kit) and remove the
light unit.
IMPORTANT When subwoofer is locat-
ed on the left side of the boot, to replace
the rear light cluster contact Fiat Dealer-
ship.
fig. 27F0C0175mfig. 28F0C0180mfig. 29F0C0388m
fig. 30F0C0208m