2006 FIAT MULTIPLA key

35
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SERVICE
The SERVICE function is used to
acquire information concerning
correct maintenance of your car.
Proceed as follows to reference
information:
Menu
Back to menu
Back to
standard display See ACCESSING
THE MAIN MENU
Qâ
ã
â
ã
âã
â
ã
ã
â
âã
â
â
ã
QR
IMPORTANT The Service Schedule establish-
es the interventions to be carried out every
20,000 km. This message will appear automat-
ically when the key is turned to MAR when a
distance of 2,000 km (or miles) before the
service deadline is reached. The message is
then represented every 200 km until there
are 200 km left to the deadline after which
the message is represented every 100 km, 50
km, etc... The data can only be reset by a Fiat
Dealership.

37
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
TRIP A (GENERAL) - TRIP B (PARTIAL)
The TRIP COMPUTER function shows the quantities related to car operation on the configurable multifunction
display. This function consists of TRIP A (general) related to the total mission of the car and TRIP B (partial) which
relates to the partial mission of the car. The latter function is part of the total mission (as shown in the following
graph). Both functions can be reset. TRIP A is used to display information concerning consumption (average
consumption), range, average speed, travel time (the time for which the car has been driven) and distance travelled.
TRIP B is used to display consumption B (average consumption), average speed B, travel time B (the time for which
the car has been driven) and distance travelled B
Start of trip procedure (reset)
To start a new trip under TRIP A, with the key at MAR, press the TRIP button in TRIP 1 (see “Control buttons”).
End mission
Start new partial mission
Reset TRIP B
˙Reset TRIP B
End mission
Start new partial mission
˙
˙Reset TRIP B
˙˙
˙
TRIP B
TRIP B
TRIP B
End mission
Start new partial missionEnd mission - Start new partial mis-
sion - Reset TRIP B TRIP A End mission
Start new general mission
Reset TRIP A
˙
End mission
Start new partial
mission - Reset TRIP A
˙
The reset procedure (pressing the TRIP button - TRIP 2, see “Control buttons” in this section) in TRIP A menu will
also reset TRIP B. The reset procedure (pressing the TRIP button - TRIP 2) in TRIP B menu will only reset the values
related to this specific function.
IMPORTANT The range value cannot be reset.

40
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DIMMER
This function is used to adjust (increase/decrease) the brightness of the instrument panel and of the display.
Standard display
Back to standard displayAfter 10s without actions Adjust brightness
Turn ignition
key to MAR
IMPORTANT The display will be dimmed when the external
lights are switched on. This function will not be available in the
event of a failure to the dimmer and the display will be on at maxi-
mum brightness.
â
ãâ
ã
Q
Switch side/
taillights on

42
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
The same lever can be used to lower it, on the rear of the centre seat
back there is a rigid surface that acts as an armrest and table with glass
holders.
Use the same lever to return the seat back to its original position.
When lowering the centre seat back make sure that the seat is pushed
back as far as it will go and that the head restraint is lowered.
Driver’s seat electrical height adjustment (where provided)
This can only be adjusted with the ignition key at MAR.
Use button (A) to adjust the seat height.
REAR SEATS
Adjustment and lowering of seat back
Lift the lever (B) and adjust the slope of the seat back. To lower use the
same lever.
The back of the centre rear seat back has a rigid surface that can be used
as a table with glass holders.
F0E0012m
F0E0013m

47
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
When driving the mirrors shall always be in position (1).
As the door mirrors are curved, they may slightly alter the perception of distance. The fixed part of the right-hand mirror reflects the
rear right wheel when parking.
This can only be adjusted with the ignition key at MAR.
Use switch (C) to select the mirror (left, neutral, right)
for adjustment.
Press any of the four directions on switch (D) located
on the ceiling light.
Switch (E) electrically controls the movement of the
folding mirrors from position 1 to position 2.
Electrically folding mirrors have a demisting device that
comes on automatically when rear window heating is
turned on.The mirrors can tilt in both directions in the event of a
collision.
To reset the mirror in the correct position, first set it
in the fully closed position by keeping the control
pressed until the mirror stops, then open it.
If the mirror is moved out of its position manually, it is
possible to set it back to the correct position
manually, although it is preferable to move it
electrically. If the mirror is moved out of its position
electrically, it is COMPULSORY to set it back
electrically to its correct position.
If the open mirror makes it difficult to pass through
narrow gaps, fold it from position 1 to position 2.

58
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
D AND
CONTROLS
If there is a fault
If an anomaly affecting the automatic system is
detected the words “AIR-COND FAULTY” will be
displayed.
The automatic system will continue to work for as
long as possible.If the fault involves the fan control (C) and the fan still
works, it will automatically operate at 1st speed.
If the fault involves an air temperature sensor, the
required air temperature control (A) will work as a
manual air temperature mixing control.
Climate control functions in automatic mode
Reason
To reach the required
temperature as soon as possible
after you get into the car
To reach the new temperature
required as quickly as possible
To prevent the entry of harmful
gas; to prevent the windows
steaming up; to speed up air
cooling
Fast window
demisting/defrosting Automatically enabled
function
Compressor on if the required
temperature is lower than or the
same as that outside
Compressor on if the required
temperature is lower than or the
same as that outside
Compressor on
Compressor on - Maximum air
flow/temperature - Air
recirculation off - Air distribution
to windows Signal to
user
Button √led on
Button √led on
Buttons √
and Tled on
Button √led on
Button Tled off Action performedby the user
Car start-up
(key to MAR)
Required
temperature
variation
Recirculation Ton
MAX/DEF
function on

59
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
EXTERNAL LIGHTS
LEFT-HAND STALK
This stalk groups together the external lights and the direction indicators.
The external lights can only be switched on when the ignition key is at
MAR.
When the external lights are turned on: the instrument panel and the
symbols of the various controls located on the dashboard will turn on.
Side and taillights
These come on when you turn the knurled switch from O to
6.
Instrument panel indicator light
3comes on.
Dipped beams
These come on when you turn the knurled switch from
6to 2.
Main beams
These come on when, with knurled knob at
2, you push the stalk
forward towards the dashboard.
Instrument panel indicator
1comes on.
To switch them off, pull the stalk towards the steering wheel.
F0E0051m
F0E0052m
F0E0053m

61
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Never use the window wiper to remove ice or snow from the windscreen. In these conditions, the
wiper is submitted to excessive effort that results in motor protection cutting in and wiper
operation inhibition for few seconds as a consequence. If operation is not restored contact Fiat
Dealership.
WINDOW CLEANING
WINDSCREEN WIPER/WASHER
This device can only work when the ignition key is at MAR.
A - Windscreen wiper off.
B - Flick wipe.
C - Slow continuous wipe.
D - Fast continuous wipe.
E - Temporary fast continuous wipe (unstable position): when the stalk is
released, it returns to position (A) automatically stopping the wiper.
When the stalk is pulled towards the steering wheel, the windscreen and
headlight washer jets starts operating (where fitted) providing the dipped
beam headlights are switched on.
F0E0056m
F0E0057m