2006 DODGE RAM 2500 DIESEL wheel torque

25. Transmission Oil Temperature Warning Light
(Automatic Transmissions Only)
This light indicates that there is excessive trans-
mission fluid temperature that might occur
with severe usage such as trailer towing. It may
also occur when operating the vehicle in a high
torque converter slip condition, such as 4-wheel-drive
operation (e.g. snow plowing, off- road operation). If this
light comes on, stop the vehicle and run the engine at idle
or faster, with the transmission in NEUTRAL until the
light goes off.
26. Wait To Start Indicator
The Wait To Start Indicator will illuminate when
the ignition key is first turned to the ON position.
Wait until the Wait To Start Indicator turns OFF then start
the vehicle.27. Odometer/Trip Odometer Button
Press this button to toggle between the odometer and the
trip odometer display. Holding the button in resets the
trip odometer reading when in trip mode.
28. Fuel Gauge
Shows level of fuel in tank when ignition switch is in the
ON position.
29. Low Fuel Warning Light
Glows when the pointer is between “E” and 1/8
indication mark (approximately 15% of tank vol-
ume) on the fuel gauge. When the fuel gauge
pointer is on “E” (equivalent to Distance To Empty [DTE]
= 0 on the overhead console if so equipped) there is
reserve fuel capacity, which corresponds to approxi-
mately 8% of tank volume. This reserve capacity was put
in place to prevent the likelihood of customers running
184 UNDERSTANDING YOUR INSTRUMENT PANEL

4. By rotating the wheel wrench clockwise, raise the
vehicle until the wheel just clears the surface.
WARNING!
Raising the vehicle higher than necessary can make
the vehicle unstable and cause an accident. It could
slip off the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.
5. Remove the wheel nuts and pull the wheel off. Install
the spare wheel and wheel nuts with the cone shaped end
of the nuts toward the wheel on 2500/3500 single rear
wheel (SRW) models. On 3500 dual rear wheel models
(DRW) the lug nuts are a two piece assembly with a flat
face. Lightly tighten the nuts. To avoid risk of forcing the
vehicle off the jack, do not fully tighten the nuts until the
vehicle has been lowered.
6. Using the wheel wrench, finish tightening the nuts
using a crisscross pattern. Correct nut tightness is 135 ft.
lbs. (183 N·m) torque for 2500/3500 single rear wheel
WHAT TO DO IN EMERGENCIES 357
6

(SRW) models and 145 ft. lbs. (197 N·m) for 3500 dual rear
wheel models. If in doubt about the correct tightness,
have them checked with a torque wrench by your dealer
or at a service station.
WARNING!
A loose tire or jack thrown forward in a collision or
hard stop could injure someone in the vehicle.
Always stow the jack parts and the extra tire and
wheel in the places provided.
7. Install wheel center cap and remove wheel blocks. Do
not install chrome or aluminum wheel center caps on the
spare wheel. This may result in cap damage.
8. Lower the jack to its fully closed position. If the jack
will not lower by turning the dial (thumb wheel) byhand, it may be necessary to use the jack drive tube in
order to lower the jack. Stow the replaced tire, jack, and
tools as previously described.
9. Adjust the tire pressure when possible.
NOTE:Do not oil wheel studs. For chrome wheels, do
not substitute with chrome plated wheel nuts.
Hub Caps/Wheel Covers
The hub caps must be removed before raising the vehicle
off the ground.
For 2500/3500 single rear wheel (SRW) models, use the
blade on the end of the lug wrench to pry the hub cap off.
Insert the blade end into the pryoff notch and carefully
pop off the hub cap with a back and forth motion.
On 3500 models with dual rear wheels (DRW), you must
first remove the hub caps. The jack handle driver has a
hook at one end that will fit in the pry off notch of the
rear hub caps. Position the hook and pull out on the
358 WHAT TO DO IN EMERGENCIES

These dual rear wheels should be tightened as follows:1. Tighten the wheel nuts in the numbered sequence to a
snug fit.
2. Retighten the wheel nuts in the same sequence to the
torques listed in the table. Go through the sequence a
second time to verify that specific torque has been
achieved. Retighten to specifications at 100 miles (160
km) and after 500 miles (800 km).
It is recommended that wheel stud nuts be kept torqued
to specifications at all times. Torque wheel stud nuts to
specifications at each lubrication interval.
Wheel Nuts
All wheel nuts should be tightened occasionally to elimi-
nate the possibility of wheel studs being sheared or the
bolt holes in the wheels becoming elongated. This is
especially important during the first few hundred miles
of operation to allow the wheel nuts to become properly
set. All nuts should first be firmly seated against the
WHAT TO DO IN EMERGENCIES 361
6

wheel. The nuts should then be tightened to recom-
mended torque. Tighten the nuts to final torque in
increments. Progress around the bolt circle, tightening
the nut opposite to the nut just previously tightened until
final torque is achieved. Recommended torques are
shown in the following chart.
Disc
WheelsType Nut Stud Size Torque
Ft. Lbs.Torque
Newton
Meters
Cone 9/16-18 120-150 160-200
Flanged 9/16-18 130-160 190-220
To Stow The Flat Or Spare
Turn the wheel so that the valve stem is down. Slide the
wheel retainer through the center of the wheel and
position it properly across the wheel opening.
For convenience in checking the spare tire inflation, stow
with the valve stem toward the rear of the vehicle.Attach the wheel wrench to the extension tube. Rotate the
winch mechanism until the wheel is drawn into place
against the underside of the vehicle. Continue to rotate
until you feel the winch mechanism slip or click 3 or 4
times. It cannot be overtightened. Push against the tire
several times to be sure it is firmly in place.
HOISTING
A conventional floor jack may be used at the jacking
locations, refer to the graphics that show jacking loca-
tions. However, a floor jack or frame hoist must never be
used on any other parts or the underbody.
CAUTION!
Never use a floor jack directly under the differential
housing of a loaded truck or damage to your vehicle
may result.
362 WHAT TO DO IN EMERGENCIES

Replacement......................... 307
Rotation............................. 311
Safety...........................291,300
Sizes............................... 293
Snow Tires........................... 311
Spare Tire........................... 352
Spinning............................ 305
Tread Wear Indicators................... 306
Wheel Mounting....................... 353
Wheel Nut Torque..................... 357
Tongue Weight/Trailer Weight.............. 326
Torque Converter Clutch.................. 270
Tow Hooks, Emergency................... 367
Towing............................... 323
Disabled Vehicle....................... 368
Guide.............................. 326
Recreational.......................... 339
Weight.............................. 326
Traction.............................. 347Traction Control......................... 406
Trailer Towing.......................... 323
Cooling System Tips.................... 333
Hitches............................. 325
Minimum Requirements................. 328
Mirrors...........................81,334
Trailer and Tongue Weight................ 326
Wiring.............................. 331
Trailer Towing Guide..................... 326
Trailer Weight.......................... 326
Transfer Case
Electronically Shifted.................... 278
Fluid............................... 439
Transmission
Automatic........................266,407
Fluid............................... 439
Maintenance.......................... 407
Manual..........................272,406
Shifting............................. 266
INDEX 491
10

Transmitter, Garage Door Opener (HomeLink) . . 141
Tread Wear Indicators.................... 306
Trip Computer.......................... 134
Trip Odometer.......................180,184
Turn Signals...................124,177,424,428
Underhood Fuses........................ 420
Uniform Tire Quality Grades................ 475
Universal Transmitter..................... 141
Variance, Compass....................... 139
Vehicle Identification Number (VIN)............ 6
Vehicle Loading......................297,319
Vehicle Modifications/Alterations.............. 7
Vehicle Storage......................... 423
Video Entertainment System
(Rear Seat Video System).................. 223
Voltmeter............................. 177Warning Lights (Instrument Cluster Description) . 177
Warnings and Cautions..................... 5
Warranty Information..................... 473
Washers, Windshield..................127,395
Washing Vehicle......................... 416
Wheel Alignment and Balance............... 308
Wheel and Wheel Trim.................... 417
Wheel Changing........................ 352
Wheel Cover........................... 358
Wheel Mounting........................ 353
Wheel Nut Torque....................357,361
Wind Buffeting.......................30,150
Window Airbag (Side Curtain)............... 52
Window Fogging........................ 243
Windows.............................. 28
Power............................... 28
Rear Sliding........................... 30
Windshield Defroster..................233,235
Windshield Washers................126,127,395
492 INDEX