2006 CHRYSLER SEBRING CONVERTIBLE hood release

Adjustable Head Restraints
Head restraints can reduce the risk of whiplash injury in
the event of impact from the rear. Adjust the restraints so
that the upper edge is as high as practical. To raise, pull
up on the head restraint. To lower, depress the button on
the post guide and push down on the head restraint.
TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull
the hood release lever located under the left side of the
instrument panel.
Then lift the secondary latch located under the front edge
of the hood, near the center and raise the hood.
Adjustable Head Restraint
Hood Release Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63
3

If Engine Fails to Start
If the engine fails to start after you have followed the
“NORMAL STARTING” or “EXTREME COLD
WEATHER” procedures, it may be flooded. Push the
accelerator pedal all the way to the floor and hold it there
while cranking the engine. This should clear any excess
fuel in case the engine is flooded.
CAUTION!
To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.
If the engine has been flooded, it may start to run, but not
have enough power to continue running when the key is
released. If this occurs, continue cranking with the accel-
erator pedal pushed all the way to the floor. Release the
accelerator pedal and the key once the engine is running
smoothly.If the engine shows no sign of starting after two 15
second periods of cranking with the accelerator pedal
held to the floor, the “NORMAL STARTING” or “EX-
TREME COLD WEATHER” procedure should be re-
peated.
After Starting
The idle speed will automatically decrease as the engine
warms up. At cooler ambient temperatures, the idle
speed for the 2.7L engine may increase during extended
idles for improved heater performance.
BATTERY AND ENGINE BLOCK HEATERS — If
EQUIPPED
The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 volt AC electrical outlet with a
grounded, three wire extension cord. The engine block
heater cord is found under the hood near the air cleaner
housing.
148 STARTING AND OPERATING

Fluid level should be maintained at the proper level
indicated on the side of the reservoir. If necessary, add
fluid to restore to the proper indicated level. With a clean
cloth, wipe any spilled fluid from all surfaces. Refer to
Fluids, Lubricants, and Genuine Parts for correct fluid
type.
Suspension Ball Joints
There are two upper front and rear suspension ball joints.
Inspect these ball joints whenever under vehicle service is
done. If the seals are damaged, the ball joint should be
replaced.
Body Mechanism Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing otherunderhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
Hood Latch
When performing other under hood services, the hood
latch release mechanism and safety catch should be
inspected, cleaned, and lubricated.
It is important to maintain proper lubrication to insure
that the hood mechanisms work properly and safely.
Multi-Purpose Lubricant, NLGI Grade 2, should be ap-
plied sparingly to all pivot and sliding contact areas.
External Lock Cylinders
Lubricate the external lock cylinders twice a year, prefer-
ably in the fall and spring. Apply a small amount of
lubricant, such as Mopar Lock Cylinder Lubricant or
equivalent directly into the lock cylinder (avoid excess
lubricant). Insert the key into the lock cylinder and rotate
from the unlocked to the locked position; without adding
more lubricant. Repeat this procedure three or four times.
Wipe all the lubricant off the key with a clean cloth, to
avoid soiling clothing.
228 MAINTAINING YOUR VEHICLE

Cleaning............................ 244
High Beam.........................69,90
High Beam/Low Beam Select Switch....... 69
Passing............................. 69
Switch.............................. 67
Time Delay........................68,69
Heater............................129,136
Heater, Engine Block.................... 148
High Beam Indicator..................... 90
Hitches
Trailer Towing....................... 187
HomeLink(Garage Door Opener) Transmitter . 75
Hood Prop............................ 64
Hood Release.......................... 63
Hoses............................236,239
Ignition
Key ................................. 9
Lock................................ 9
Illuminated Entry....................... 12
Immobilizer (Sentry Key).................. 10
Infant Restraint......................... 35
Inside Rearview Mirror................... 56Instrument Cluster..................86,87,88
Instrument Panel and Controls.............. 85
Instrument Panel Cover.................. 245
Instrument Panel Lens Cleaning............ 245
Interior Fuses.......................... 248
Interior Lighting........................ 65
Interior Lights........................65,66
Introduction............................ 4
Jack Location.......................... 200
Jack Operation......................... 200
Jump Starting......................... 204
Key, Programming....................... 11
Key, Replacement........................ 11
Key, Sentry (Immobilizer).................. 10
Key-In Reminder......................... 9
Keyless Entry System..................... 15
Keys.................................. 9
Lap/Shoulder Belts...................... 23
LATCH (Lower Anchors and
Tether for CHildren)...................37,39
294 INDEX

Tread Wear Indicators................... 172
Trip Computer.......................... 95
Trip Odometer.......................... 92
Trip Odometer Reset Button................ 92
Trunk Release, Emergency...............20,21
Trunk Release Remote Control.............. 20
Turn Signals.........................68,90
Underhood Fuses....................... 248
Uniform Tire Quality Grades.............. 284
Universal Transmitter.................... 75
Unleaded Gasoline...................... 178
Vacuum/Vapor Harnesses................ 236
Vanity Mirrors.......................... 58
Vehicle Identification Number (VIN).......... 6
Vehicle Loading........................ 164
Vehicle Modifications/Alterations............ 6
Vehicle Storage......................... 250
Vehicle Theft Alarm (Security Alarm)......... 19
Vinyl Trim............................ 243
Viscosity, Engine Oil..................... 257
Voltmeter.............................. 90Warning, Door Ajar...................... 14
Warning Flasher, Hazard................. 198
Warnings and Cautions.................... 6
Warranty Information.................... 282
Washer, Adding Fluid................... 230
Washers, Windshield..................69,230
Washing Vehicle........................ 242
Waxing and Polishing................... 242
Wheel Alignment and Balance............. 174
Wind Buffeting......................... 22
Window Fogging....................... 133
Windows.............................. 21
Power.............................. 21
Windshield Washers...................69,230
Windshield Wipers.................68,69,229
Wiper Blade Replacement................. 230
Wipers, Intermittent...................... 70
Wood Trim Cleaning.................... 245
INDEX 301
10