2006 CHRYSLER PACIFICA light

INTEGRATED POWER MODULE (IPM)
An Integrated Power Module is located in the engine
compartment near the battery. This center contains maxi
fuses, mini fuses and relays. A label that identifies each
component is printed on the inside of the cover.
Cavity Maxi Fuse Description
1 40 Amp Green Anti-Lock Brake System
(ABS) Pump
2 Spare
3 30 Amp Pink Ignition Off Draw (IOD)
4 40 Amp Green Body Control Module
(BCM) Feed 1
5 40 Amp Green Electronic Back Light (EBL)
6 30 Amp Pink Front Wipers
7 40 Amp Green Starter
8 40 Amp Green Power Seat C/B
9 40 Amp Green Power Sunroof
Integrated Power Module (IPM)
MAINTAINING YOUR VEHICLE 377
7

Cavity Maxi Fuse Description
10 Spare
11 40 Amp Green Headlight Washer, Power
Liftgate
12 Spare
13 40 Amp Green Radiator Fan 1
14 Spare
15 40 Amp Green Anti-Lock Brake System
(ABS) Module
40 40 Amp Green Driver Door Node
41 40 Amp Green Passenger Door Node
42 40 Amp Green Front BlowerCavity Mini Fuse Description
24 20 Amp Yel- low Power Outlet (Selectable)
25 15 Amp Blue Radio, Amplifier, Naviga- tion, Hands-Free Phone
(HFM), Electronic Vehicle
Information Center (EVIC),
EC, SNRF, Mirror
26 20 Amp Yel- low Power Outlet
27 Spare
28 25 Amp Natural Horn
29 20 Amp Yel- low Cluster, CHMSL, Stop
Lights, Anti-Lock Brake
System (ABS)
30 10 Amp Red Ignition Switch
31 20 Amp Yel- low Hazard
378 MAINTAINING YOUR VEHICLE

REPLACEMENT LIGHT BULBS
LIGHT BULBS — Interior Bulb Number
Center & Rear Reading Lights ............... 578
Front Door Courtesy Light .................. 578
Liftgate Light(s) .......................... 578
Overhead Console Reading Lights ...........212–2
Visor Vanity Lights ..................... V26377
NOTE: For lighted switches, see your dealer for replace-
ment instructions.
All of the interior bulbs are glass wedge base or glass
cartridge types. Aluminum base bulbs are not approved
and should not be used for replacement. LIGHT BULBS — Exterior Bulb Number
Back-up
............................... 921
Rear Stop, Turn Signal .................... 3157
Rear Sidemarker ......................... 168
Fog Light ............................. 9145
Front Turn Signal ....................... 3157A
Front Sidemarker ......................... 194
Standard Headlight ....................... H7
License ................................ 168
MAINTAINING YOUR VEHICLE 381
7

BULB REPLACEMENT
Standard Quad Headlights
1. Remove the two screws securing the headlight mod-
ule to the vehicle and pull the headlight module forward
away from the vehicle, disengaging the assembly from
the lower attachment clip. 2. Remove the rubber boot seals.
3. Disconnect the electrical connector.
4. Rotate the bulb to the left and replace the bulb.
Reinstall the rubber boot seals and then the headlight
module.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
382 MAINTAINING YOUR VEHICLE

High Intensity Discharge Headlights (HID) — If
Equipped
The headlights are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlight switch off and the key removed. Because of
this, you should not attempt to service a headlight bulb
yourself. If a headlight bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb sockets of
High Intensity Discharge (HID) headlights when the
headlight switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced prop-
erly. See your authorized dealer for service.
NOTE: On vehicles equipped with High Intensity Dis-
charge Headlights (HID), when the headlights are turned
on there is a blue hue to the lights. This diminishes and
becomes more white after approximately 10 seconds, as
the system charges.
MAINTAINING YOUR VEHICLE 383
7

Front Park/Turn Signal and Sidemarker Lights
1. Remove the two screws securing the headlight mod-
ule to the vehicle and pull the headlight module forward
away from the vehicle, disengaging the assembly from
the lower attachment clip.
2. Twist the bulb socket to remove from the headlight
module and pull the bulb from socket. 3. Replace the bulb, reinstall the socket and then reinstall
the headlight module.
Front Fog Light
1. Reach under the front fascia and grasp the front fog
light bulb.
2. Twist the front fog light bulb to remove from the fog
light module.
3. Disconnect the electrical connector and replace the
bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
384 MAINTAINING YOUR VEHICLE

Rear Tail, Stop, Turn Signal, Side Marker and
Back-up Lights
1. Raise the liftgate.
2. Remove the two tail light assembly screws and rotate
the assembly outward to remove the ball stud form the
attaching grommet. 3. Twist the socket assembly to remove it from the
housing.
4. Pull the bulb out of the socket.
5. Replace the bulb, reinstall the socket, and reattach the
tail light assembly.
License Light
1. Place a screwdriver in the slot next to the release tab
and push on the release tab to remove the lens.
2. Pull the bulb out of the socket. Replace the bulb and
push on the lens until it snaps into place.
MAINTAINING YOUR VEHICLE 385
7

Once a Month
•Check tire pressure and look for unusual wear or
damage.
•Inspect the battery and clean and tighten the terminals
as required.
•Check the fluid levels of coolant bottle, brake master
cylinder and transmission, add as needed.
•Check all lights and all other electrical items for correct
operation. At Each Oil Change
•Change the engine oil filter.
•Inspect the exhaust system.
•Inspect the brake hoses.
•Inspect the CV joints and front suspension compo-
nents.
•Check the automatic transmission fluid level.
•Check the coolant level, hoses, and clamps.
392 MAINTENANCE SCHEDULES
8
M
A I
N T
E
N A
N C E
S
C
H E
D
U L
E
S