2006 CADILLAC STS door lock

You may be able to close the windows from outside
the vehicle using the lock button on the keyless access
transmitter. The engine must be off. Press and hold the
lock button for more than two seconds to close any open
window(s) on your vehicle. If any window is unable to
close completely, it will reverse and the horn will chirp.
See “Anti-Pinch Feature” underPower Windows on
page 2-18for more information.
You can program your vehicle so the turn signal
indicators will not ash and the horn will not sound
when pressing the lock button on the keyless access
transmitter. For more information see “Lights Flash at
Lock” and “Horn Chirps at Lock” underVehicle
Personalization on page 2-53.
/(Remote Start):Pressing this button operates the
remote start feature. See “Remote Vehicle Start” at
the end of this section for more detailed information.
"(Unlock):Press this button once to unlock the
driver’s door. The turn signal indicators will ash twice.
Press the unlock button twice within ve seconds to
unlock all the doors. If it is dark enough outside, your
interior lamps will come on.You can program your vehicle so the turn signal
indicators will not ash and the fog lamps and reverse
lamps remain on steady for approximately 20 seconds
when the keyless access transmitter is used to unlock the
vehicle. See “Lights Flash at Lock” and “Ext. (Exterior)
Lights at Unlock” underVehicle Personalization
on page 2-53.
If your vehicle has the memory feature you can program
and recall memory settings when you press the unlock
button on the keyless access transmitter. SeeMemory
Seat, Mirrors and Steering Wheel on page 2-70for more
information.
G(Trunk):Press and hold this button for
approximately one second to open the trunk while the
engine is turned off or the shift lever is in PARK (P).
L(Vehicle Locator/Panic Alarm):Press and
release this button to locate your vehicle. The horn
will chirp three times and the turn signal lamps will ash
three times. Press and hold the button for three seconds
to sound the panic alarm. The horn will chirp and the turn
signal lamps will ash for 30 seconds. Press and release
the button again to cancel the panic alarm.
2-6

Matching Transmitter(s) to
Your Vehicle
Each Keyless Access System is coded to allow only
transmitters programmed to your vehicle to work. If
a transmitter is lost or stolen, a replacement can be
purchased and programmed through your GM dealer.
Your GM dealer can reprogram your vehicle so lost or
stolen transmitters no longer work with your vehicle.
Each vehicle can have a maximum of four transmitters
matched to it.
To match a new transmitter to your vehicle when
you have a recognized transmitter, do the following.
Two recognized transmitters are required for
Canadian owners.
1. The vehicle must be off.
2. Have the recognized transmitter and the new,
unrecognized transmitter(s) with you.
3. Insert the vehicle key into the key lock cylinder
located on the outside of the driver’s door.
4. Turn the key to the unlock position ve times within
ve seconds.
5. The Driver Information Center (DIC) will display
READY FOR FOB #X, where X can be 2, 3 or 4.6. Place the new, unrecognized transmitter into the
transmitter pocket with the transmitter buttons facing
the front of the vehicle. The transmitter pocket is
inside the center console storage area located
between the driver and front passenger seats.
7. Once the transmitter is programmed, a beep will
sound. The DIC will display READY FOR #X, where
Xcanbe3or4,orMAX#FOBSLEARNED.
8. Remove the transmitter from the transmitter pocket
and press the unlock button on the keyless access
transmitter two times.
2-7

The Canadian immobilizer standard requires Canadian
owners to see their GM dealer for matching new
transmitters when a recognized transmitter is not
available. United States Owners are permitted to match
a new transmitter to their vehicle when a recognized
transmitter is not available. The procedure will require
three, ten minute cycles to complete the matching
process. Do the following:
1. The vehicle must be off.
2. Place the new, unrecognized transmitter into the
transmitter pocket with the transmitter buttons facing
the front of the vehicle. The transmitter pocket is
inside the center console storage area located
between the driver and front passenger seats.3. Insert the vehicle key into the key lock cylinder
located on the driver’s door.
4. Turn the key to the unlock position ve times within
ve seconds.
5. The DIC message will display OFF/ACC
TO LEARN.
6. Press the ACC button (ignition switch).
7. The DIC will read WAIT 10 MINUTES and will
count down to zero, one minute at a time.
8. The DIC will display OFF/ACC TO LEARN again.
9. Press the ACC button (ignition switch) again.
10. The DIC will again read WAIT 10 MINUTES and
will count down to zero, one minute at a time.
11. The DIC will display OFF/ACC TO LEARN again.
12. Press the ACC button (ignition switch) again.
13. The DIC will again read WAIT 10 MINUTES and
will count down to zero, one minute at a time.
14. A beep will sound and the DIC will read READY
FOR FOB #1. At this time, all previously known
transmitters have been erased.
15. Once the transmitter is recognized and
programmed, a beep will sound and the DIC will
display READY FOR FOB #2.
16. Remove the keyless access transmitter and press
the unlock button twice to initialize it.
2-8

3. Put the new battery in the transmitter, positive (+)
side down. Use a battery type CR2032 or
equivalent.
4. Reassemble the transmitter. Make sure to put it
together so water will not get inside the transmitter.
5. Test the transmitter.
Remote Vehicle Start
This feature allows you to start the engine from outside
the vehicle.
/(Remote Start):To start the vehicle using the
remote start feature, do the following:
1. Aim the remote keyless access transmitter at the
vehicle.
2. Press the transmitter’s lock button, release it, and
then immediately press and hold the transmitter’s
remote start button for at least three seconds or until
the vehicle’s turn signal lamps ash. The vehicle’s
doors will be locked.
3. When the vehicle starts, the parking lamps will turn
on and remain on while the vehicle is running.
4. Repeat Steps 1 and 2 while the engine is still
running to add 10 minutes of engine running.If the vehicle is left running it will automatically shut off
after 10 minutes unless a time extension has been done.
To manually shut off a remote start, do any of the
following:
Aim the keyless access transmitter at the vehicle and
press the remote start button until the parking lamps
turn off.
Turn on the hazard warning ashers.
Press the ACC button (ignition switch). SeeIgnition
Positions on page 2-24.
Turn on the valet lockout switch. SeeValet Lockout
Switch on page 2-23.
When you enter the vehicle during a remote start,
press the brake pedal and press the start button on the
keyless ignition switch to transition from remote start
operation to normal vehicle operation.
Before the remote vehicle start system can be operated
with the keyless access transmitter it must be activated.
The remote start system is turned on through the vehicle
personalization system.
You can also program the remote vehicle start system
to start up the vehicle’s automatic climate control
system. If this feature is turned on, the system monitors
the outside temperature and turns on the rear window
defogger, front window defogger, and heated or
ventilated seats, if equipped. See “Personal Settings
Menu” underVehicle Personalization on page 2-53.
2-10

Doors and Locks
Door Locks
{CAUTION:
Unlocked doors can be dangerous.
Passengers, especially children, can easily
open the doors and fall out of a moving
vehicle. When a door is locked, the handle
will not open it. You increase the chance
of being thrown out of the vehicle in a
crash if the doors are not locked. So, wear
safety belts properly and lock the doors
whenever you drive.
Young children who get into unlocked
vehicles may be unable to get out. A child
can be overcome by extreme heat and can
suffer permanent injuries or even death
from heat stroke. Always lock your vehicle
whenever you leave it.
Outsiders can easily enter through an
unlocked door when you slow down or
stop your vehicle. Locking your doors can
help prevent this from happening.There are several ways to lock and unlock your vehicle.
From the outside, press the lock or unlock button
on the keyless access transmitter. When you have
your transmitter with you, you may also unlock and
open the door by pulling the door handle. You do not
have to press the unlock button on the transmitter. Entry
occurs when the door handle is pulled and the vehicle
recognizes your transmitter. SeeVehicle Personalization
on page 2-53for information on how to program the
keyless access feature.
From the inside, use the power door lock switches
located on each front door. SeePower Door Locks
on page 2-12for more information. The rear passenger
doors have manual door lock knobs located at the top of
the door panel near the window. Push down the knob to
lock the door. Pull up the knob to unlock the door.
Power Door Locks
The power door lock switches are located on the
armrest on the front doors.
K(Unlock):Press the side of the switch with the
unlock symbol to unlock the doors.
Q(Lock):Press the side of the switch with the lock
symbol to lock the doors.
2-12

Programmable Automatic
Door Locks
Your vehicle was programmed from the factory so that
when the doors are closed, the ignition is on and the shift
lever is moved out of PARK (P), all the doors will lock.
The front doors can still be opened from the inside while
the doors are locked. If a rear passenger needs to exit
the vehicle, have that person use the manual knob or use
the power door lock switch on either front door. When the
door is closed again, it will not lock automatically. Use
the manual knob or the power door lock switch to lock
the door.
The doors were also programmed from the factory to
unlock every time the shift lever is moved back into
PARK (P).
The power door locks can be programmed through the
radio display. The radio display allows you to choose
various lock and unlock settings. For more information
on programming, seeVehicle Personalization on
page 2-53.
Rear Door Security Locks
Your vehicle is equipped with rear door security locks
that prevent passengers from opening the rear doors on
your vehicle from the inside.
The rear door security locks
are located on the inside
edge of each rear door.
You must open the rear
doors to access them.
To use these locks, do the following:
1. Insert your key into the slot next to the rear door
security lock label and turn it to engage the lock.
2. Close the door.
3. Repeat the steps for the other rear door.
The rear doors on your vehicle cannot be opened from
the inside when this feature is in use.
2-13

When you want to open a rear door when the security
lock is on, do the following:
1. Unlock the door using the remote keyless entry
transmitter, the front door power lock switch or
by lifting the rear door manual lock.
2. Then open the door from the outside.
To cancel the rear door security lock, do the following:
1. Unlock the door and open it from the outside.
2. Insert your key into the slot next to the rear door
security lock label and turn it to disengage the lock.
3. Repeat the steps for the other lock.
The rear door locks will now work normally.
Lockout Protection
Your vehicle can be programmed to sound the horn
three times and unlock the driver’s door when all doors
are closed and there is a keyless access transmitter
inside the interior of the vehicle. When the driver’s door
is reopened, the key in reminder chime will sound
continuously. The vehicle will remain locked only when
at least one transmitter has been removed from the
vehicle and both doors are closed. SeeVehicle
Personalization on page 2-53.
Trunk
{CAUTION:
It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You cannot see or
smell CO. It can cause unconsciousness and
even death. If you must drive with the trunk lid
open or if electrical wiring or other cable
connections must pass through the seal
between the body and the trunk lid:
Make sure all other windows are shut.
Turn the fan on your heating or cooling
system to its highest speed and select the
control setting that will force outside air
into your vehicle. See Climate Control
System.
If you have air outlets on or under the
instrument panel, open them all the way.
SeeEngine Exhaust on page 2-39.
2-14

Trunk Lid Release
There are several ways to release the trunk lid.
V(Trunk Lid Release):Press this button
located on the driver’s door. The vehicle must be
in PARK (P) or NEUTRAL (N) and the valet mode
turned off. To disable valet mode, seeValet Lockout
Switch on page 2-23.
Press the trunk lid release button on the keyless
access transmitter. SeeKeyless Access System
Operation on page 2-5. The vehicle must be in
PARK (P) or NEUTRAL (N) and the valet mode
turned off.
Squeeze the trunk release button located on the
rear of the trunk lid above the license plate, as
long as you have your keyless access transmitter
with you. Entry occurs when the button is being
pressed and the vehicle recognizes the transmitter.
The vehicle must be in PARK (P) and the valet
mode turned off.
If your vehicle has lost battery power, you can still
access the trunk by unlocking and lowering the rear seat
pass-through door and pulling the emergency trunk
release handle.
2-15