2006 CADILLAC DTS display

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. SeeTurn and
Lane-Change Signals on page 3-8.
3Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on page 3-9.
Flash-To-Pass Feature. SeeFlash-to-Pass
on page 3-13.
NWindshield Wipers. SeeWindshield Wipers on
page 3-13.
LWindshield Washer. SeeWindshield Washer
on page 3-15.
_Heated Washer Fluid. SeeWindshield Washer
on page 3-15.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is
complete. If you momentarily press and release the
lever, the turn signal will ash 3 times.
An arrow on the instrument
panel cluster and in the
outside rearview mirror will
ash in the direction of
the turn or lane change.
Raise or lower the lever until the arrow starts to ash
to signal a lane change. Hold it there until the lane
change is complete. The lever returns when it is released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON after driving about a mile to remind
you to turn it off.
Arrows that ash rapidly when signaling for a turn or
lane change may be caused by a burned out signal bulb.
Other drivers will not see the turn signal.
Replace burned-out bulbs to help avoid possible
accidents. Check the fuse and for burned-out bulbs if
the arrow fails to work when signaling a turn. SeeRear
Underseat Fuse Block on page 5-96.
3-8

Windshield Washer
{CAUTION:
In freezing weather, do not use your washer
until the windshield is warmed. Otherwise the
washer uid can form ice on the windshield,
blocking your vision.
J(Washer Fluid):Press and release this paddle,
located at the top of the turn signal/multifunction lever,
to spray washer uid on the windshield. The wipers
will clear the windshield and either stop or return to your
preset speed. For more washer cycles, press and
hold the paddle.
_(Heated Washer Fluid):If your vehicle is equipped,
the heated windshield washer uid system may be
used to help clear ice, snow, tree sap, or bugs from
your windshield. Sliding the switch on the turn signal/
multifunction lever to this position and then releasing
it will activate the heated windshield washer uid system.
This activation will initiate four heated wash/wipe cycles.
The rst heated wash/wipe cycle may take up to
40 seconds to occur, depending on outside temperature.
After the rst wash/wipe cycle, it may take up to
20 seconds for each of the remaining cycles. The heated
windshield washer uid system may be turned off at any
time by sliding the switch on the turn signal/multifunction
lever to this position again.
When the heated windshield washer uid system is
activated under certain outside temperature conditions,
steam may ow out of the washer nozzles for a short
period of time before washer uid is sprayed. This is a
normal condition.
A message will be displayed on the Driver Information
Center (DIC) when the washer uid is low. SeeDIC
Warnings and Messages on page 3-76.
3-15

The cruise control buttons
are located on left side of
the steering wheel.
I(On):This position activates the system.
+ RES (Resume/Accelerate):Press this button to
make the vehicle accelerate or resume to a previously
set speed.
–SET (Set):Press this button to set the speed.
[(Cancel):Press this button to cancel cruise control.
Cruise control will not work if your parking brake is
set, or if the master cylinder brake uid level is low.
If you apply your brakes, the cruise control will shut off.The cruise light on the instrument panel cluster will
come on after the cruise control has been set to
the desired speed.
1. Press the cruise control button.
2. Get up to the speed you want.
3. Press the SET button located on the steering wheel
and release it.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This shuts off the
cruise control. But you do not need to reset it.
Once the vehicle is traveling approximately
25 mph (40 km/h) or more, you can press the
RES (resume/accelerate) button to return to your
desired preset speed. The cruise light will be displayed
again.
The vehicle will return to and stay at your preset speed.
If you press and hold the RES button, the vehicle
speed will increase until you release the button or apply
the brake. Unless you want to go faster, do not press
and hold the RES button.
3-17

To set Adaptive Cruise Control, do the following:
1. Press the
](On) button.
2. Get up to the speed you want.
3. Press in the−SET button and release it.
4. Take your foot off the accelerator pedal.
Once Adaptive Cruise Control is set, it may immediately
apply the brakes if it detects a vehicle ahead is too
close or moving slower than your vehicle.
The on symbol is located on the display at the top of
the instrument panel to the right of the driver. When
the on symbol is lit on the display, it indicates that
Adaptive Cruise Control is active.
A message on the DIC will also display when Adaptive
Cruise Control is set. SeeDIC Warnings and
Messages on page 3-76.
Keep in mind speed limits, surrounding traffic speeds,
and weather conditions when adjusting your set speed.
If your vehicle is in Adaptive Cruise Control when the
traction control system begins to limit wheel spin, the
Adaptive Cruise Control will automatically disengage.
SeeTraction Control System (TCS) on page 4-9and
StabiliTrak
®System on page 4-10. When road conditions
allow you to safely use it again, you may turn the
Adaptive Cruise Control back on.
Increasing Set Speed While Using Adaptive
Cruise Control
There are two ways to increase the set speed:
Use the accelerator to get to the higher speed.
Press the SET button and then release the
button and the accelerator pedal. You will now
cruise at the higher speed.
Press the RES button. Hold it there until the desired
set speed is displayed on the Driver Information
Center (DIC), then release the switch. To increase
your set speed in very small amounts, move the
switch briey to RES. Each time you do this,
your vehicle set speed will increase by
1 mph (1 km/h).
Your vehicle will not reach the set speed until the
system determines there is not a vehicle in front of you.
At that point, your vehicle speed will increase to the
set speed.
3-23

Alerting the Driver
The Adaptive Cruise
Control alert symbol is
located on the display at
the top of the instrument
panel to the right of
the driver.
The alert symbol will ash and a warning beep will
sound when driver action may be required. If Adaptive
Cruise Control is engaged, the alert symbol will
ash when:
Adaptive Cruise Control cannot apply sufficient
braking because you are approaching a vehicle
too rapidly.
The vehicle speed drops below about
20 mph (32 km/h).
A temporary condition prohibits Adaptive Cruise
Control from operating. SeeDIC Warnings and
Messages on page 3-76for more information.
A malfunction is detected in the system. SeeDIC
Warnings and Messages on page 3-76for more
information.
SeeDefensive Driving on page 4-2.
{CAUTION:
Adaptive Cruise Control has only limited
braking ability to slow your vehicle. In some
cases, Adaptive Cruise Control may not have
time to slow your vehicle enough to avoid a
collision. Be ready to take action and apply the
brakes yourself. SeeDefensive Driving on
page 4-2.
Approaching and Following a Vehicle
The Vehicle Ahead symbol is located on the top of the
instrument panel to the right of the driver.
The Vehicle Ahead symbol will only appear when a
vehicle is detected in your path.
3-25

Instrument Panel Brightness
D(Instrument Panel Brightness):This feature
controls the brightness of the instrument panel lights.
The button for this control is located below the exterior
lamps control.
Push the button in and release to extend the button.
Turn the button clockwise for brightness of the
instrument panel lights and counter clockwise to turn
the brightness down.
Courtesy Lamps
The courtesy lamps are located on the headliner above
the rear seat. These lamps come on by turning the
instrument panel brightness knob fully clockwise or when
any door is opened and it is dark outside. Puddle
lamps are located on the bottom of the front and rear
door trim.
Professional vehicles have an additional dome lamp and
also opera lamps.
Entry Lighting
This feature turns on the courtesy lamps and the
backlighting to the door switches and to the exterior
lamp control when a door is opened or if you press the
remote keyless entry transmitter unlock button. If
activated due to the transmitter, the lighting will remain
active for about 40 seconds. Since the entry lighting
system uses the light sensor, it must be dark outside in
order for the courtesy lamps to turn on. The courtesy
lamps turn off approximately 25 seconds after the
last door is closed. They will dim to off if the ignition key
is turned to RUN, or immediately deactivate if the
power locks are activated.
Parade Dimming
This feature prohibits dimming of the digital displays and
backlighting during daylight hours when the key is in
the ignition and the headlamps are on. This feature is
fully automatic. When the light sensor reads darkness
outside and the parking lamps are active, the digital
displays can be adjusted by turning the instrument panel
brightness knob counterclockwise to dim and clockwise
to brighten lighting.
3-36

The front display is located on top of the instrument
panel to the right of the driver. The rear display is
located near the rear window and can be seen by
looking over your right shoulder. The rear display has
three color-coded lights. The front display will have
either three or six lights depending on whether
your vehicle is equipped with Adaptive Cruise Control
(ACC). If your vehicle has ACC, it will have three lights
along with the ACC lights. If your vehicle does not
have ACC, it will have six UFRPA lights.The UFRPA lights are used to provide distance and
system information, along with beeps played out either
the front or rear speakers. For objects detected near
the front bumper, high-toned beeps will be played
out the front speakers. For objects detected near the
rear bumper, low-toned beeps will be played out the
rear speakers.
How the System Works
When the vehicle is started, the front display will
briey illuminate to let you know the display is
operating correctly. When the shift lever is moved into
REVERSE (R), the rear display will briey illuminate
to let you know the display is operating correctly.
UFRPA comes on automatically when the shift lever is
moved out of PARK (P). The system does not work
at a forward speed greater than 5 mph (8 km/h), so
the front display indicators are turned off. The system
also does not work at a reverse speed greater than
5 mph (8 km/h). To remind you of this, the red light on
the rear display will ash.
The system can be disabled using the Driver Information
Center (DIC). SeeDIC Controls and Displays on
page 3-72. Front Parking Assist
Display
Rear Parking Assist
Display
3-39

When you are backing the vehicle and objects are
detected at the same time near both the front and rear
bumpers, both color-coded light displays will notify
you of objects close to each bumper. If there are objects
detected near both bumpers, the beeps will only be
sounded to notify that objects are close to the rear
bumper. However, if while you are backing and an object
comes within 1 ft (0.3 m) of the front bumper, and at
the same time there is another object further than
1 ft (0.3 m) from the rear bumper, then the beeps will
only be sounded to notify you of the closer object that is
near the front bumper.
When the System Does Not Seem to
Work Properly
If the UFRPA system will not activate due to a temporary
condition, the message PARKING ASSIST OFF will
be displayed on the DIC and a red light will be shown on
the rear UFRPA display when the shift lever is moved
into REVERSE (R). This occurs under the following
conditions:
The driver disables the system. SeeDIC Controls
and Displays on page 3-72.
The parking brake pedal is depressed.
A trailer was attached to your vehicle, or a bicycle
or an object was hanging out of your trunk during
your last drive when you turned off the vehicle. If the
attached objects are removed from your vehicle
before the start of your next drive, the system will
return to normal operation unless an object is
detected when the vehicle is shifted out of park.
If this occurs, you will have to wait until the vehicle
is driven forward above 15 mph (25 km/h) before
UFRPA will return to normal operation.
A bicycle or an object is attached to the front
bumper during your last drive when you turned off
the vehicle. If the attached objects are removed
from your vehicle before the start of your next drive,
the system will return to normal unless an object
is detected when the vehicle is shifted out of park.
If this occurs, UFRPA will return to normal
operation when the vehicle is driven forward
above 15 mph (25 km/h).
The ultrasonic sensors are not kept clean.
So be sure to keep your vehicle’s front and rear
bumpers free of mud, dirt, snow, ice and slush.
For cleaning instructions, seeWashing Your Vehicle
on page 5-86. If after cleaning the front and rear
bumpers and driving forward at a speed of
at least 15 mph (25 km/h), the DIC displays the
PARKING ASSIST OFF message, see your dealer.
3-41