2006 CADILLAC DTS radio

Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the
hills. When going up steep hills, you may have to step
on the accelerator pedal to maintain your speed.
When going downhill, you may have to brake or shift to
a lower gear to keep your speed down. Applying the
brake or shifting into a lower gear will take you out
of cruise control. If you need to apply the brake or shift
to a lower gear due to the grade of the downhill
slope, you may not want to attempt to use your cruise
control feature.
Ending Cruise Control
To turn off the cruise control, step lightly on the brake
pedal, or press the cancel button on the steering wheel.
Erasing Speed Memory
When you turn off the cruise control or the ignition, your
cruise control set speed memory is erased.
Adaptive Cruise Control
If your vehicle has this feature, be sure to read this
entire section before using it.
The system operates on a radio frequency subject to
Federal Communications Commission (FCC) Rules and
with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
3-19

Other conditions that may affect system performance
include vibrations from a jackhammer or the
compression of air brakes on a very large truck or
other mechanical devices that interfere with UFRPA
performance.
When UFRPA is disabled without driver action and
the driver attempts to turn UFRPA back on using the
Driver Information Center (DIC), the PARKING
ASSIST ON option will not be selectable if the
necessary conditions stated above for normal system
operation are not met.
As always, drivers should use care when backing up a
vehicle. Always look behind you, being sure to check
for other vehicles, obstructions and blind spots.
For Driver Information Center messages related to
UFRPA, seeDIC Warnings and Messages on
page 3-76.
If the bumper is damaged, your UFRPA system may
not work properly. Take the vehicle to your dealer
to repair the system.
Accessory Power Outlet(s)
Your vehicle is equipped with accessory power outlets.
The outlets can be used to plug in electrical equipment
such as a cellular telephone, CB radio, etc.
If your vehicle has a stationary center console, the
power outlet is located inside the lower storage area.
There are outlets also on the right front lower part of the
driver’s seat and in the lower storage bin. SeeCenter
Console Storage Area on page 2-50.
There are two accessory power outlets in the rear
seat area located on the door armrests next to the
ashtrays.
Your vehicle may have a small cap that must be
removed to access the accessory power outlet. If it
does, when not using the outlet be sure to cover it with
the protective cap.
The accessory power outlet can be used at any time.
Notice:Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
3-42

Cigarette Lighter
Notice:Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
The cigarette lighter is located near the front ashtray.
Press the lighter all the way in and release it. It will pop
back out by itself once the element has heated for use.
Cigarette lighters can be used to provide electrical
power to accessories. SeeAccessory Power Outlet(s)
on page 3-42for more information.
Analog Clock
The clock is located on the instrument panel above the
radio. To adjust the clock, do the following:
1. Locate the adjustment button directly below the
clock face.
2. Push and hold the adjustment button to advance
the clock hands. Holding the button down will
cause the clock to advance faster. Release the
buttonbeforeyou get to the desired time.
3. Push and release the button to increase the time by
one minute increments until the desired time is
reached.
Climate Controls
Dual Climate Control System
With this system you can control the heating, cooling
and ventilation for your vehicle. To avoid window fogging
on rainy and humid days at temperatures above
freezing, run the air conditioning compressor. Also, it is
best to avoid the use of recirculation mode except
when maximum air-conditioning performance is needed
for a short amount of time to avoid exterior odors
and fogging.
Climate Control Panel for Vehicles with Rear
Climate Control
3-44

Audio System(s)
Determine which radio your vehicle has and then
read the pages following to familiarize yourself with
its features.
Driving without distraction is a necessity for a safer
driving experience. SeeDefensive Driving on page 4-2.
By taking a few moments to read this manual and
get familiar with your vehicle’s audio system, you can
use it with less effort, as well as take advantage of
its features. While your vehicle is parked, set up your
audio system by presetting your favorite radio stations,
setting the tone, and adjusting the speakers. Then,
when driving conditions permit, you can tune to
your favorite stations using the presets and
steering wheel controls if the vehicle has them.{CAUTION:
This system provides you with a far greater
access to audio stations and song listings.
Giving extended attention to entertainment
tasks while driving can cause a crash and you
or others can be injured or killed. Always keep
your eyes on the road and your mind on the
drive — avoid engaging in extended searching
while driving.
Keeping your mind on the drive is important for safe
driving. For more information, seeDefensive Driving
on page 4-2.
3-97

Here are some ways in which you can help avoid
distraction while driving.
While your vehicle is parked:
Familiarize yourself with all of its controls.
Familiarize yourself with its operation.
Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
conditions permit, you can tune to your favorite
radio stations using the presets and steering wheel
controls if the vehicle has them.
Notice:Before adding any sound equipment to
your vehicle, such as an audio system, CD player,
CB radio, mobile telephone, or two-way radio, make
sure that it can be added by checking with your
dealer. Also, check federal rules covering mobile
radio and telephone units. If sound equipment can
be added, it is very important to do it properly.
Added sound equipment may interfere with
the operation of your vehicle’s engine, radio, or
other systems, and even damage them. Your
vehicle’s systems may interfere with the operation
of sound equipment that has been added.Notice:The chime signals related to safety belts,
parking brake, and other functions of your vehicle
operate through the radio/entertainment system.
If that equipment is replaced or additional equipment
is added to your vehicle, the chimes may not
work. Make sure that replacement or additional
equipment is compatible with your vehicle before
installing it. SeeAccessories and Modifications
on page 5-3.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, the audio system can be
played even after the ignition is turned off. SeeRetained
Accessory Power (RAP) on page 2-24for more
information.
Setting the Time (Radio with Single
CD Player)
Enabling the Digital Radio Clock
Your vehicle has an analog clock as well as the digital
radio clock. At the time of new vehicle delivery, the
digital radio clock display should be disabled. If
you decide to use the digital radio clock as well as the
analog clock, you can change the setting to enable
the radio clock display.
3-98

Turn the radio clock display on or off by following
these steps:
1. Press the clock button until the clock and date
setting menus appear.
2. Press the pushbutton located under the forward
arrow label until the menu for default clock and
date settings appear.
3. Press the pushbutton located under the currently
displayed status of either ON or OFF. The ON
display indicates the radio clock display is disabled
and the OFF display indicates the radio clock
display is enabled. Press this pushbutton to toggle
the radio clock display on or off.
If the radio clock display is turned on, the screen
will display Radio Clock ON for ve seconds,
then return to the original clock display menu.
If the radio clock display is turned off, the screen
will display Radio Clock OFF for ve seconds. The
menus for clock and date settings will be removed,
and the ON display will appear as a current
status indicating that the clock display can be
turned on, if desired.
The radio clock and analog clock are not synchronized.
Occasionally you may need to set the digital radio
clock using the procedure below to synchronize
both clocks.Setting the Time and Date on the Digital
Radio Clock
If your vehicle has a radio with a single CD player, it
has a clock button for setting the time and date. To set
the time and date, do the following:
1. Press the clock button and HR, MIN, MM, DD,
YYYY (hour, minute, month, day, and year) will
appear on the display.
2. Press the pushbutton located under each one of
the labels that you want to change. Every time the
pushbutton is pressed again, the time or the
date if selected, will increase by one.
Another way to increase the time or date, is to
press the right SEEK arrow or the FWD button.
3. To decrease the time or date, press the left SEEK
arrow or the REV button. You can also rotate the
tune knob to adjust the selected setting.
3-99

Changing the Time and Date Default
Setting
To change the time and date default setting, do the
following:
1. Change the time default setting from 12 hour to
24 hour or the date default setting from month/day/
year to day/month/year, by pressing the clock button.
2. Once the clock and date settings are displayed
along with the forward arrow, press the pushbutton
located under the forward arrow until the time
12H and 24H, and the date MM/DD/YYYY (month,
day, and year) and DD/MM/YYYY (day, month,
and year) are displayed.
3. Press the pushbutton located under the desired
option, then press the clock button again to apply
the selected default, or let the screen time out.
Setting the Time (Radio with
Six-Disc CD Player)
Enabling the Digital Radio Clock
Your vehicle has an analog clock as well as the digital
radio clock. At the time of new vehicle delivery, the
digital radio clock display should be disabled. If
you decide to use the digital radio clock as well as the
analog clock, you can change the setting to enable
the radio clock display.Turn the radio clock display on or off by following
these steps:
1. Press the MENU button until the clock label
display appears.
2. Press the pushbutton located under the clock label
until the clock and date settings appear.
3. Press the pushbutton located under the forward
arrow label until the menu for default clock and
date settings appear.
4. Press the pushbutton located under the currently
displayed status of either ON or OFF. The ON
display indicates the radio clock display is disabled
and the OFF display indicates the radio clock
display is enabled. Press this pushbutton to toggle
the radio clock display on or off.
If the radio clock display is turned on, the screen
will display Radio Clock ON for ve seconds,
then return to the original clock display menu.
If the radio clock display is turned off, the screen
will display Radio Clock OFF for ve seconds. The
menus for clock and date settings will be removed,
and the ON display will appear as a current
status indicating that the clock display can be turned
on, if desired.
The radio clock and analog clock are not synchronized.
Occasionally you may need to set the digital radio clock
using the procedure below to synchronize both clocks.
3-100

Setting the Time and Date on the Digital
Radio Clock
If your vehicle has a radio with a six-disc CD player, it
has a MENU button for setting the time and date. To set
the time and date, do the following:
1. Press the MENU button until the clock option is
displayed.
2. Press the pushbutton located under the clock label
and the HR, MIN, MM, DD, YYYY (hour, minute,
month, day, and year) will appear on the display.
3. Press the pushbutton located under each one of
the labels that you want to change. Every time the
pushbutton is pressed again, the time or the
date if selected, will increase by one.
Another way to increase the time or date, is to
press the right SEEK arrow or the FWD button.
4. To decrease the time or date, press the left SEEK
arrow or the REV button. You can also rotate the
tune knob to adjust the selected setting.
Changing the Time and Date
Default Setting
To change the time and date default setting, do the
following:
1. Change the time default setting from 12 hour to
24 hour or the date default setting from month/day/
year to day/month/year, by pressing the MENU
button.
2. Once the clock symbol is displayed, press the
pushbutton located under that symbol until the
time and date settings are displayed along with a
forward arrow.
3. Press the pushbutton located under the forward
arrow until the time 12H and 24H, and the date
MM/DD/YYYY (month, day, and year) and
DD/MM/YYYY (day, month, and year) are displayed.
4. Press the pushbutton located under the desired
option, then press the MENU button again to
apply the selected default, or let the screen
time out.
3-101