and cycles through the follow-
ing sequence:Total distance covered
Tripmeter 1 (Trip I)
Tripmeter 2 (Trip II)Resetting tripmeterSwitch on the ignition.
Select the desired tripmeter.
Press and hold down
button 1until the reading
changes.
The tripmeter is reset to
zero.
Residual rangeThe residual-range readout 1
indicates how far you can ride
with the fuel remaining in the
tank. On a motorcycle not
equipped with an on-board
computer, this reading is not
displayed until fuel level has
dropped to reserve. This dis-
tance is calculated on the
basis of fuel level and average
consumption.
When you refuel, the increase
in fuel level is not registered
unless several litres are ad- ded to the fuel already in the
tank.
The residual range is
only an approximate
reading. Consequently, BMW
Motorrad recommends that
you should not try to use the
full residual range before
refuelling.
ClockSet the clock
Attempting to set the
clock while riding the
motorcycle can lead to ac-
cidents.
Set the clock only when the
motorcycle is stationary.
Switch on the ignition.
444zOperation
The on-board computer's dis-
play field starts with the cur-
rent value and cycles through
the following sequence:Ambient temperature
Average speed
Average consumption
Range
Oil level
Tyre pressures (OE)
Ambient temperatureAmbient-temperature dis-
play 1is active only when
the engine is running; at other
times the display shows
---
.
An ice warning appears
if the ambient-temper-
ature reading drops below
3 °C. The display automat-
ically switches from any oth-
er mode to the temperature
reading when the temperature
drops below this threshold
for the first time. The reading
flashes until you select some
other display mode.
Calculating average
speedAverage speed 1is calculated
on basis of the time elapsed
since the last RESET. Times
during which the engine was
stopped are excluded from
the calculation.
447zOperation
Resetting average speedRepeatedly press INFO
button1until the average
speed appears in the
display.
Press and hold down the
INFO button until the read-
ing changes ("RESET").
The display shows
"--- km/h".
Calculating average
consumptionAverage consumption 1is
calculated by dividing the dis-
tance covered since the last
RESET by the corresponding
amount of fuel used.
Reset average
consumptionRepeatedly press INFO but-
ton 1until the average fuel
consumption appears in the
display.
Press and hold down the
INFO button until the read-
ing changes ("RESET").
The display shows
"--.- l/100 km".
448zOperation
ImmobiliserWarning, 26
Instrument cluster Overview, 18
Sensor for lighting, 18
J
Jump start, 114
L
Laying up, 124
Lights Switch on the high-beam
headlight, 52
Switching off parking
lights, 53
Switching on parking
lights, 53
Switching on the low-beam
headlight, 52
Switching on the side
lights, 52 M
Maintenance
General instructions, 86
Intervals, 143
Mirrors Adjusting, 57, 58
Multifunction display, 18, 22
O
Odometer and tripmeters, 22 Operation, 43
Pushbutton, 16
Resetting tripmeter, 44
Selecting readings, 43
On-board computer Ambient temperature, 47
Average consumption, 48
Average speed, 47
Oil level, 49
Pushbutton, 16
Range, 49
Reset average consump-
tion, 48 Resetting average
speed, 48
Selecting readings, 46
P
Power socket, 11
Pre-ride check, 67
R
Rear-wheel stand Installing, 106
Refuelling, 71
Reserve Warning, 26
Residual range, 44
Restoring to use, 125
Rev. counter, 18
Running gear Technical data, 135
11154zIndex
