2006 BMW 7 SERIES AUX

Downloaded from www.Manualslib.com manuals search engine 2 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
Installation information
The Auxiliary jack G1 must always be installed on the left-hand side of the monitor trim AT.
Ensure that the cables/lines are not kinked or damaged as you install them in the car. The costs incurred
as a result of this will not be reimbursed by BMW AG.
Additional cables/lines that you install must be secured with cable ties.
If the specified PIN chambers are already used, bridges, double crimps or twin-lead terminals must be
used.
Deburr holes and treat them with anti-corrosive coatings as set out in BMW directives to protect them
from corrosion.
Ordering instructions
The monitor trims AC/AT are not supplied in the retrofit kit and must be ordered separated in the interior
trim colours of the car or in a primed finish (see EPC for part numbers and further details).
The multimedia changer L is not included in the retrofit kit and must be ordered separately for the
appropriate region code (see EPC for part number and further details).
The monitor AA is not included in the retrofit kit and must be ordered separately (see EPC for part
number and further details).
List of special equipment
SA 456Comfort seat, front
SA 601TV function
Special tools required
00 9 317, Installation wedge

Downloaded from www.Manualslib.com manuals search engine 4 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
1. Parts list
Legend
AConnection cable
BVoltage supply
CMultimedia changer AV adapter
DConnection wiring harness (left seat, length 5200 mm)
EConnection wiring harness (right seat, length 6700 mm)
FSeat wiring harness (2x)
GAuxiliary cable (jack diameter 2.5 mm, 2x)
HHeadphone cable (jack diameter 3.5 mm, 2x)
IFan wiring harness
JMultimedia changer power supply cable
KAuxiliary adapter (2x)
LMultimedia changer (not supplied with the retrofit kit)
MHexagonal screw M5 x 14 mm (not required)
NAdhesive patches (supplied with the multimedia changer kit)
OMounting plate
PSpacer plate (2x)










M
IJK
DEFG
H
OP
B
A
LN
C

 


Downloaded from www.Manualslib.com manuals search engine 11 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
3. Connection diagram
FSeat wiring harnessLMultimedia changer
F18-pin round plug, SWL1Cinch plug, WS
F2WS 10-pin plugL2Cinch plug, RT
F38-pin round plug, SWL3Cinch plug, GE
F48-pin round plug, SWL4Black 4-pin plug
L5Black 4-pin plug
GAuxiliary cable
G1Auxiliary jack (2.5 mm)UAV switcher
G28-pin round plug, SW
AAMonitor
HHeadphone cableAA18-pin round plug RT
H1Headphone jack (3.5 mm)
H28-pin round plug RT
JMultimedia changer power supply
cable
J18-pin round plug, SW
J2WS 3-pin plug
J
C
D
HH
G
E
G
FF
U
L
D3E3
B2
L5 L1-L3 C3-C5
L4 C2
J2 J1
B3B1 E2
E1F3
F4F1F2
G2AA1
AA1 H2
G1
G2 G1H1
H2 H1
B
F2
F1
F3
D2
D1F4
AA AA
D4E4C1

  

Downloaded from www.Manualslib.com manuals search engine 24 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
8. To install the monitor
Secure the adhesive marking (1) that you pre-
viously fitted on the seat wiring harness F to the
seat backrest (2) as shown using a cable tie AP.
Thread branches F1 and F2 through the front
seat rear panel (1).
Install the front seat rear panel (1) as described in
TISRA5215198.
Unscrew the tooth washer (1) and hexagonal nut (2)
from the auxiliary cable
G and headphone cable H.
Insert the auxiliary cable G into the front monitor
trim AT on the left and secure it with a toothed
washer (1) and hexagonal nut (2).
Insert the headphone cable H into the front
monitor trim AT on the right and secure it with a
toothed washer (1) and hexagonal nut (2).
Insert grommets AL into the monitor AA.
Thread headphone connector AA1 for the
monitor AA through the top grommet AL.
Insert cable ties AP into the existing holes.
1
21
F
APAP



 
1
F2
F1


 
21G
HAT


 
ALAP
AA1
AP
AA