2006 Acura TL reset

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.Driver 1 or 2 Detected
Door and Trunk Open
Fasten Seat Belt
Release Parking Brake
Odometer
Trip Meter
Outside Temperature
Engine Oil Lif e Maintenance Messages
Auto door lock conditions
Auto door unlock conditions
Whenever unlocking (driver’s
door, or all doors)
Keyless lock acknowledgment
conditions
Security relock timer
Headlight auto of f timer
Interior light dimming time
To customize these control settings,
see page .
Low Windshield Washer Fluid
Level (Canada only)
Here is a list of the messages you
can see. The f ollowing pages give
you more inf ormation on these
messages.
Tighten Fuel Cap With the multi-information display
and the two buttons next to it, you
can also customize these vehicle
control settings to your liking.Language Selection (Canada only) HandsFree Link
Keyless Memory Settings
Trip Computer
Tire Pressure
76
Multi-Inf ormation Display
67
SELECT/
RESET
BUTTON
INFO
BUTTON
TMTM

The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.This meter show the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. When you first turn the ignition
switch to ON (II), Trip A is displayed.
Switch between Trip A and Trip B by
pressing the Select/Reset button
repeatedly. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
If the f luid level in the windshield
washer reservoir gets low, the multi-
inf ormation display shows the above
message.
On Canadian models
L ow Windshield Washer Fluid
Level
Odometer
T rip Meter
Multi-Inf ormation Display
71
ODOMETER
TRIP METER

¶¶µµµµ
µ µµµ
Both trip meters will reset if the
vehicle’s battery goes dead or is
disconnected. This shows the outside Fahrenheit
temperature in U.S. models, and
Centigrade temperature in Canadian
models.
To reset a trip meter, display it, then
press and hold the Select/Reset
button until the number resets to
‘‘0.0.’’
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace. If the outside temperature is
incorrectly displayed, you can adjust
it up to 5°F ( 3°C) warmer or
cooler.
NOTE: The temperature must be
stabilized bef ore doing this
procedure.
Select the outside temperature
display, then press the Select/Reset
button f or 10 seconds. The f ollowing
sequence will appear f or 1 second
each:0,1,2,3,4,5, 5, 4, 3, 2,1, 0, 1 (0, 1, 2, 3, 3, 2, 1, 0, 1).
When it reaches the desired value,
release the Select/Reset button. You
should see the new outside
temperature displayed.
The temperature sensor is in the
f ront bumper. The temperature
reading can be affected by heat
ref lection f rom the road surf ace,
engine heat, and the exhaust f rom
surrounding traf f ic. This can cause
an incorrect temperature reading
when your speed is under 19 mph (30 km/h). When you start
your trip, the sensor is not f ully
acclimatized, theref ore it may take
several minutes until the proper
temperature is displayed.
Outside Temperature
Multi-Inf ormation Display
Inst rument s and Cont rols
72
SELECT/
RESET
BUTTON

This shows the remaining lif e of the
engine oil. It shows 100% af ter the
engine oil is replaced and the display
is reset. The engine oil lif e is
calculated based on engine operating
conditions and accumulated engine
revolutions.When the engine oil lif e reaches 15
percent, the display shows
‘‘SERVICE DUE SOON’’ and the
code f or the maintenance items to be
perf ormed.Have your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display af ter completing the service.
If you do not perf orm the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil lif e becomes 0 percent.
These messages appear on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.
When the engine oil lif e reaches 5
percent, the display shows
‘‘SERVICE DUE NOW’’ along with
the same maintenance items. For details on engine oil lif e and
maintenance messages, ref er to page
.
Also ref er to page f or important
maintenance saf ety precautions. 209
208
Engine Oil L if e
Maintenance Messages
Multi-Inf ormation Display
73

¼
When you press the side of the
INFO button three times af ter you
turn the ignition switch to the ON
(II) position, you will see the above
display. To see the inf lation pressure of all
f our tires, press the SEL/RESET
button. The display changes as
shown above.
If one or more of your vehicle tires
are low on pressure, you will see a
‘‘CHECK TIRE PRESSURE’’
message in the display.
If there is a problem with the TPMS,
you will see a ‘‘CHECK TPMS
SYSTEM’’ message.
See page through f or
complete inf ormation about the
TPMS.
204 206
Multi-Inf ormation Display
Tire Pressure Monitoring System
(TPMS) Messages
74

¼
When the multi-information display
is in the trip computer mode, press
the Select/Reset button. The display
changesasshownabove. Themessagesinthisdisplay
indicate:
AVG MPG: Average vehicle speed
AVG MPH: Average f uel economy
DIST: Distance traveled
TIME: Time traveled
To reset the values in the trip
computer, press the Select/Reset
button, and hold it f or about 1
second.
When the display shows the initial
trip computer screen, press the
side of the INFO button to display
‘‘RANGE’’. This is the estimated
distance you can travel on the fuel
remaining in the tank. This distance
is estimated f rom the f uel economy
you received over the last several
miles, so it will vary with changes in
speed,traffic,etc.
Multi-Inf ormation Display
Trip Computer
Inst rument s and Cont rols
75

¼
Select the menu item you want
(‘‘CHG SETTINGS’’, ‘‘DEFAULT
ALL’’ or ‘‘EXIT’’) by moving the
pointer ‘‘ ’’ with the INFO button.
Af ter selecting a menu item, enter
your selection by pressing the
Select/Reset button.
To exit this mode without changing
the current settings, select ‘‘EXIT’’
and press the Select/Reset button.
The display will move to the next
mode.
If you want to change the settings,
select ‘‘CHG SETTINGS’’, and press
the Select/Reset button. The display
will change to the screen shown in
the middle column of this page.
While ‘‘Keyless Memory Settings’’ is
displayed, press the Select/Reset
button. The display will change to
the screen shown above. Auto door lock conditions
Auto door unlock conditions
Keyless lock acknowledgment
conditions
Security relock timer
Headlight auto of f timer
Interior light dimming time
With the vehicle stopped and the
transmission in Park (A/T) or the
parking brake set (M/T), you can
customize some of the vehicle
control settings to your pref erence.
Here are the settings you can
customize:
Multi-Inf ormation Display
K eyless Memory Settings
76
TM

»¼¼
¼
If you want the settings as they were
when the vehicle lef t the f actory,
select ‘‘DEFAULT ALL’’ and press
the Select/Reset button. The display
will change to the screen shown
above. Press the Select/Reset button
to select ‘‘OK’’ or press the or
side of the INFO button to cancel. Therearethreepossiblesettings:
OFF: The auto door lock is
deactivated all the time.
SHIFTFROMP:Thedoorswilllock
whenever you move the shif t lever
out of P. (Models with automatic
transmission.)
10 MPH: The doors will lock when
the vehicle speed reaches 10 mph.
The f irst Keyless Memory Setting is
Auto Door Lock conditions. Select
the desired condition by moving the
pointer with the side of the INFO
button. On the display, will be
next to the current setting.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
77