2006 Acura TL automatic transmission

´´
Although this seems like a simple
procedure, you should take several
precautions.
You cannot start a vehicle with an
automatic transmission by pushing
or pulling it. Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or like ice, do not try
jump starting until it thaws.
Turn of f all the electrical acces-
sories: heater, A/C, stereo system,
lights, etc. Put the transmission in
neutral or Park, and set the
parking brake.
The numbers in the illustration
show you the order to connect the
jumper cables.
Connect one jumper cable to the
positive ( ) terminal on your
battery. Connect the other end to
the positive ( ) terminal on the
booster battery.
1.
2.
3.
Jump Starting
To Jump Start Your Vehicle:
252
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.

If you do not see steam or spray,
leave the engine running, and
watch the temperature gauge. If
the high heat is due to overloading,
the engine should start to cool
down almost immediately. If it
does, wait until the temperature
gauge comes down to the midpoint,
then continue driving.
The pointer of the vehicle’s
temperature gauge should stay in
the midrange. If it climbs to the red
mark, you should determine the
reason (hot day, driving up a steep
hill, etc.).
If the vehicle overheats, you should
take immediate action. The only
indication may be the temperature
gauge climbing to or above the red
mark. Or you may see steam or
spray coming f rom under the hood.
If the temperature gauge stays at
the red mark, turn of f the engine.
Look f or any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you f ind a leak, it
must be repaired bef ore you
continue driving (see
on page ).
If you see steam and/or spray
coming f rom under the hood, turn
of f the engine. Wait until you see
no more signs of steam or spray,
then open the hood. Saf ely pull to the side of the road.
Put the transmission in neutral
(manual) or Park (automatic), and
set the parking brake. Turn of f all
the accessories, and turn on the
hazard indicators.
1.
2. 3.
4.
5.
263
If theEngineOverheats
Emergency
Towing
254
Steam and spray from an
overheated engine can
seriously scald you.
Do not open the hood if steam
is coming out.
Driving with the temperature gauge
pointer at the red mark can cause
serious damage to the engine.

µµThe operator
loads your vehicle on the back of a
truck.
The tow
truck uses two pivoting arms that go
under the tires (f ront or rear) and lif t
them of f the ground. The other two
tires remain on the ground.
If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do this: Release the parking brake.
Shif t the transmission to neutral.
If your vehicle is equipped with a
f ront spoiler, remove it bef ore
towing so it is not damaged.
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
behind another vehicle with just a
rope or chain. It is very dangerous.
Therearetwowaystotowyour
vehicle:
Release the parking brake.
Start the engine.
ShifttoD,thentoN.
Turn of f the engine.
With the f ront wheels on the ground,
it is best to tow the vehicle no farther
than 50 miles (80 km), and keep the
speedbelow35mph(55km/h). If you decide to tow your vehicle
with all f our wheels on the ground,
make sure you use a properly-
designed and attached tow bar.
Prepare the vehicle for towing as
described above, and leave the
ignition switched in the
ACCESSORY (I) position so the
steering wheel does not lock. Make
sure the radio and any items plugged
into the accessory power socket are
turned of f so they do not run down
the battery.
Manual Transmission:
Automatic Transmission:
CONT INUED
Emergency Towing
Flat -bed Equipment
Wheel-lif t Equipment
This is the best way to trans-
port your vehicle.
T his is
an acceptable way to tow your
vehicle.
T aking Care of t he Unexpect ed
263
Trying to lif t or tow your vehicle by the
bumpers will cause serious damage.
The bumpers are not designed to
support the vehicle’s weight.
Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine (automatic transmission), your
vehicle must be transported with the
f ront wheels of f the ground.

µµÎ
Î
Î
Î
Specif ications
270
Dimensions
Weights
Capacities Capacities
Air Conditioning 186.2 in (4,730 mm)
72.2 in (1,835 mm)
56.7 in (1,441 mm)
107.9 in (2,740 mm)
62.1 in (1,577 mm)
62.0 in (1,576 mm)
HFC-134a (R-134a)
17.6 19.4 oz (500 550 g) ND-OIL8
2.6 US qt (2.5
)
7.6 US qt (7.2
)
3.1 US qt (2.9)
5.3 US qt (5.0)
4.2 US qt (4.0
)
4.5 US qt (4.3
)
0.16 US gal (0.6
)
2.3 US qt (2.2
)
2.6 US qt (2.5)
4.8 US qt (4.5
)
2.14 US gal (8.1
)
2.09 US gal (7.9)
1.66 US gal (6.3
)
1.69 US gal (6.4)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating
Fuel tank Engine
coolant
Engine oil
Automatic
transmission
fluid
Manual
transmission
fluid
Windshield
washer
reservoir
Refrigerant type
Charge quantity
Lubricant type
See the certification label attached
to the driver’s doorjamb.
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity:
Approx.
Front
Rear
1:
2:Change
Manual
Automatic
Total Manual
Automatic
Change Including
filter
Without
filter
Total
Change
Total
Change
Total
U.S. Vehicle
Canada Vehicle
1
2
17.1 US gal (64.7)

µ
µ
Î
Î
Î
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
Î
ÎÎ
Specif ications
Technical Inf ormation
271
Engine
Alignment
Tires
Lights
Battery
Fuses
3.50 x 3.39 in (89.0 x 86.0 mm)
195.9 cu-in (3,210 cm
)
11.0 : 1
0.00 in (0.0 mm)
0.00 in (0.0 mm) 0°30’
1°00’
3°17’
P235/45R17 93W 235/45R17 93W IZFR6K-11
SKJ20DR-M11
35 psi (240 kPa , 2.4 kgf/cm
)
33 psi (230 kPa , 2.3 kgf/cm)
32 psi (220 kPa , 2.2 kgf/cm)
60 psi (420 kPa , 4.2 kgf/cm)
T145/70R17 106M T135/80R16 101M
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
Water cooled 4-stroke
SOHC VTEC 6-cylinder (V6), gasoline engine
Toe-in
Camber
Caster
Size
Pressure
12 V 12 V
12 V
12 V
12 V
12 V
12 V 12 V 21 W 12 V 60 W (HB3) 12 V 35 W (HID)
Headlight
(High beam/Low beam)
DRL (Canadian models)
Front/Rear turn signal lights
Front Fog lights (U.S.models)
Front parking lights
Back-up lights
License plate light
Ceiling light
Trunk light
Door courtesy lights
Vanity mirror lights
Map lights 12 V
12 V
51 W (HB4)
5W
21 CP
3CP
5W
5W
2CP
5W
4CP
Capacity 12 V 65 AH/20 HR
Interior
Under-hood See page262or the fuse label
attached to the inside of the fuse
box door on each side of the
dashboard.
See page261or the fuse box
cover. Front
Rear
Front
Rear
Front
NGK:
DENSO:
Front/Rear
Spare
Front
Rear
Spare
All season tire
Summer tire
Vehicles with manual transmission
Vehicles with automatic transmission
1:
2:
3:
4: Automatic:
Manual:
1
2
34

The exhaust emissions controls
include f our systems: PGM-FI,
ignition timing control, exhaust gas
recirculation, and three way catalytic
converter. These f our systems work
together to control the engine’s
combustion and minimize the
amount of HC, CO, and NOx that
come out the tailpipe. The exhaust
emissions control systems are
separate f rom the crankcase and
evaporative emissions control
systems.The emissions control systems are
designed and certif ied to work
together in reducing emissions to
levels that comply with the Clean Air
Act. To make sure the emissions
remain low, you should use only new
Acura replacement parts or their
equivalent f or repairs. Using lower
qualitypartsmayincreasethe
emissions f rom your vehicle.
The emissions control systems are
covered by warranties separate from
the rest of your vehicle. Read your
warranty manual for more informa-
tion.
The three way catalytic converter is
in the exhaust system. Through
chemical reactions, it converts HC,
CO, and NOx in the engine’s exhaust
to carbon dioxide (CO ), nitrogen
(N ), and water vapor. The exhaust gas recirculation (EGR)
system takes some of the exhaust
gas and routes it back into the intake
manif old. Adding exhaust gas to the
air/f uel mixture reduces the amount
of NOx produced when the f uel is
burned. This system constantly adjusts the
ignition timing, reducing the amount
of HC, CO, and NOx produced.
The PGM-FI system uses sequential
multiport f uel injection.
It has three subsystems: air intake,
engine control, and f uel control. The
powertrain control module (PCM) in
automatic transmission vehicles or
the engine control module (ECM) in
manual transmission vehicles uses
various sensors to determine how
much air is going into the engine. It then controls how much f uel to inject
under all operating conditions.
2
2
Emissions Cont rols
Exhaust Emissions Controls Replacement Parts
PGM-FI System
Three Way Catalytic Converter
Exhaust Gas Recirculat ion (EGR)
Syst em
Ignit ion T iming Cont rol Syst em
Technical Inf ormation
275

Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
If you take your vehicle f or a state
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions. If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle retested within the
next two or three days, you can
condition the vehicle f or retesting by
doing the f ollowing.
Keep the vehicle in Park
(automatic transmission) or
neutral (manual transmission).
Increase the engine speed to 2,000
rpm,andholditthereuntilthe
temperature gauge rises to at least
1/4of thescale(about3minutes).
Make sure the vehicle has been
parked with the engine of f f or 6
hours or more.
Make sure the ambient
temperature is between 40° and
95°F.
CONT INUED
State Emissions T esting
T esting of Readiness Codes
Technical Inf ormation
277

CONT INUED
...
Accessories and Modif ications .181
................................
Accessories .181
............................
Modif ications .182
ACCESSORY (Ignition Key .......................................
Position) .90
............
Accessory Power Sockets .115
................
Adding Engine Coolant .221
........................
Adding Engine Oil .218
....................
Additives, Engine Oil .219
.............................
Airbag (SRS) .11,23
...............
Additional Information .23
......................................
Servicing .32
...................
System Components .23
..............
Air Conditioning System .122
.......................
Air Pressure, Tires .234
......................................
Antif reeze .221
Anti-lock Brakes (ABS) ...............................
Indicator .61,201
...................................
Operation .201
..............
Anti-thef t, Audio System .151
.
Anti-thef t Steering Column Lock .90
................................
Audio System .127
...
Automatic Lighting Off Feature .86
...
Automatic Seat Belt Tensioners .21 .............
Automatic Speed Control .153
..............
Automatic Transmission .193
..........................
Capacity, Fluid .270
...............
Checking Fluid Level .223
.......................................
Shif ting .193
.
Shif t Lever Position Indicator .193
.......................................
Shif ting .193
....................
Shif t Lock Release .197
Battery Charging System ...........................
Indicator .60,256
............................
Jump Starting .252
..............................
Maintenance .240
............................
Specif ications .271
..............................
Bef ore Driving .175
..................................
Belts, Seat .10,20
...........................
Beverage Holder .115
Brakes ...........
Anti-lock System (ABS) .201
.............
Break-in, New Linings .176
...........................................
Fluid .225
.......................................
Parking .112
.................
System Indicator .60,258 ........................
Wear Indicators .200
.............................
Braking System .200
.................
Break-in, New Vehicle .176
..
Brightness Control, Instruments .85
........................
Brights, Headlights .84
Bulb Replacement ..........................
Back-up Lights .230
.................................
Fog Lights .227
............................
Specif ications .271
............
Turn Signal Lights .228,229
..............................
Bulbs, Halogen .227
............................
Capacities Chart .270
.............
Carbon Monoxide Hazard .53
............................
Carrying, Cargo .183
Cassette Player ............................................
Care .149
...................................
Operation .147
..............
CAUTION, Explanation of .ii
..................................
Ceiling Light .113
........................
Certif ication Label .268
...................................
Chains, tires .239
Index
A
BC
INDEX
I