2006 Acura TL buttons

µ
µ Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Press the button again.
The other XM band will show.
Store the next six channels using
steps 2 and 3.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
Youcanstoreupto12
preset channels using the six preset
buttons or preset icons (on models
with navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
To store a channel: Press the button. Either
XM1 or XM2 will show in the
display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In category mode, only channels
within that category can be selected.
In channel mode, all channels can be
selected.
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or 5
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. 1.
2.3.
4.
5.
Playing the XMSatellite Radio (U.S. Models)
Preset
SCAN
136

´´
µ
µ
Playing Discs
140
DISC
BUTTON LOAD
BUTTON
SEEK
BUTTONS
EJECT
BUTTON
SEEK
BUTTONS DISC
SLOT
DISC BUTTON
DISC BUTTON
RANDOM BUTTON
DISC BUTTON
RANDOM BUTTON REPEAT BUTTON
SCAN BUTTON DISC
SLOT
CD/DVD BUTTON
U.S. Models (with Navigation System)
Canadian Models (without Navigation System)
REPEAT
BUTTON SCAN
BUTTON LOAD
BUTTON DISC/TAPE
BUTTON AM/FM
BUTTON
PWR/VOL
KNOB PWR/VOL
KNOB
EJECT
BUTTON AM
BUTTON
FM
BUTTON

µ´µ´
µ
µ
´
Select the disc changer by pressing
the DISC/TAPE button (U.S.
models) or CD/DVD button
(Canadian models). The system will
begin playing the last selected disc in
the disc changer. You will see the
disc and track numbers displayed.
To select a dif f erent disc when all six
positions are loaded, use the preset 5
(DISC ) or preset 6 (DISC )
button. Otherwise, press the
corresponding number on the preset
buttons or icons. On models with
navigation system, you can also
touch the appropriate disc icon (1
6) to select a dif f erent disc.
WhenyoupressandholdtheSCAN
button until you see D-SCAN in the
display, or when you touch the DISC
SCAN icon on the audio display
(models with navigation system), the
f irst track of the current disc plays
f or about 10 seconds. You will see D-
SCAN (DISC SCAN) in the display.
To hear the rest of the disc, press
the SCAN button or touch DISC
SCAN again, within 10 seconds. If
you don’t, the system advances to
the next disc, plays about 10 seconds
of it, and continues throughout the
rest of the discs the same way.
When the system reaches the last
disc, DISC SCAN is cancelled, and
the disc you originally had on plays
normally.
Each time you press and release the
SEEK button, the player skips
f orward to the beginning of the next
track. Press and release the SEEK
buttontoskipbackwardtothe
beginning of the current track or to
skip back to previous track.
When you press the SCAN button or
touchtheTRACKSCANicononthe
audio display (models with
navigation system), the f irst track of
the current disc plays f or about 10
seconds. You will see SCAN
(TRACK SCAN) highlighted in the
display. To hear the rest of the track,
press the SCAN button or touch
TRACK SCAN again within 10
seconds. If you don’t, the system
advances to the next track, plays
about 10 seconds of it, and continues
through the rest of the tracks the
same way.
The preset 5 (DISC ) and preset 6
(DISC ) buttons are f or use with
an optional, external CD changer. T o Play a Disc
T o Change T racks Disc Scan
Track Scan
Playing Discs
Features
142

Playing a T ape
147
DOLBY BUTTON
CD/DVD BUTTON
REWIND BUTTON
PLAY/PROGRAM BUTTON Canadian Models (without Navigation System)
U.S. Models (with Navigation System)
FAST FORWARD BUTTON FAST FORWARD BUTTON
DOLBY BUTTON SEEK
BUTTONS EJECT
BUTTON
REWIND BUTTON
PLAY/PROGRAM BUTTON REPEAT
BUTTON PWR/VOL
KNOB DISC/TAPE
BUTTON AM/FM
BUTTON PWR/VOL
KNOB FM
BUTTON
REPEAT
BUTTON
AM
BUTTON
EJECT
BUTTON
SEEK
BUTTONS
TAPE BUTTON

If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code. If you are
unsuccessf ul in 10 attempts, you
must then leave the system on for 1
hour bef ore trying again.
If thecodecardislost,yourdealer
can access your code with your
radio’s serial number. To access the
serial number, turn the radio on. It
must display ‘‘CODE’’, then turn theradio of f . Push the preset 1, preset 6,
and power buttons at the same time,
then quickly release. The serial
number will appear in two sets of
f our digits.
Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code in the
preset buttons. Because there are
hundreds of number combinations
possible f rom f ive digits, making the
system work without knowing the
exact code is nearly impossible.
Youshouldhavereceivedacardthat
lists your audio system code number
and serial number. It is best to store
this card in a saf e place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
If youshouldhappentolosethecard,
you must obtain the code number
f rom your dealer. To do this, you will
need the system’s serial number. If your vehicle’s battery is discon-
nected or goes dead, the audio
system will disable itself . If this
happens, you will see ‘‘CODE’’ in the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons to enter the five-digit code.
Thecodeisontheradiocodecard
included in your owner’s manual kit.
When it is entered correctly, the
radio will start playing.
Radio T hef t Protection
151

µ
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. They do not
have the safety feature that causes the motor to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury.
The HomeLink
Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remote controlled devices
around your home, such as garage
doors, lighting, or home security
systems. Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment. If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button.
Todothis,pressandholdthetwo
outside buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red indicator in
HomeLink.
For quick and accurate training,
make sure the remote control
transmitter for the device (garage
door, automatic gate, security
system, etc.) has a fresh battery.
1.
2.
Bef ore you begin
General Inf ormationImportant Saf ety PrecautionsT raining HomeL ink
HomeL ink Universal Transceiver
Features
156

Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time.If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5. If the red indicator in HomeLink
continues to f lash slowly (does
not f lash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds. If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to f lash slowly (does
not begin to f lash rapidly),
repeat steps 2 thru 4.
Plug in the garage door opener
motor, then test the HomeLink
button by pushing it f or about 1 second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink. If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
If the indicator f lashes rapidly
f or 2 seconds then stays on, you
have a rolling code transmitter:
Go to ‘‘Training with a Rolling
Code System’’ (see page ).
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
3.
4.
5.6.
7.
158
HomeL ink Universal Transceiver
157

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red
indicator begins to f lash, then
release the buttons. If a standard transmitter was
programmed, the indicator will
stay on f or about 25 seconds.
Once the HomeLink indicator
begins to f lash slowly, continue to
hold the HomeLink button, and
f ollow steps 3 thru 6 under
‘‘Training HomeLink’’ (see page ).
If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com.
HomeLink
is a registered
trademark of Johnson Controls, Inc.
Youshoulderaseallthreecodes
bef ore selling the vehicle.
If you want to retrain a programmed
button f or a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure:
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds.
1. 2.
157
Erasing Codes
Customer Assistance
Retraining a Button
HomeL ink Universal Transceiver
159