2006 Acura RL light

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to theupper end of the white section of the
gauge. If it reaches the red (hot)
mark, pull saf ely to the side of the
road. For more information, see page
. This shows how much f uel you
have. It may show slightly more
or less than the actual amount.
The needle returns to the
bottom after you turn off the
ignition.
406
Gauges
Temperature Gauge Fuel Gauge
70
U.S. model is shown.TACHOMETER
TEMPERATURE GAUGE
SPEEDOMETER
FUEL GAUGE
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

Û
Ý
ÛÝ
You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize:
While the multi-information display
is in the CUSTOMIZE ENTRY
screen, press the SEL/RESET
button. The screen changes to the
initial CUSTOMIZE GROUP display.
METER SET UP ADAPTIVE CRUISE CONTROL
SETUP
Each time you press the INFO ( /) button, the screen changes as
shownonthenextpage.Pressthe
INFO ( / ) button, until you see
the setup you want to customize,
then press the SEL/RESET button
to enter your selection.
POSITION SET UP
LIGHTING SET UP
DOOR/WINDOW SET UP
WIPER SET UP
Multi-Inf ormation Display
Customize Settings
84

ÛÝ
Multi-Inf ormation Display
Inst rument s and Cont rols
85
Press the or button.
Press the SEL/RESET button.ADAPTIVE CRUISE
CONTROL SET UP
seepage86
METER SET
UP
seepage91
POSITION
SET UP
see page100
KEYLESS
ACCESS SET UP
see page105
LIGHTING
SET UP
see page112
DOOR/WINDOW
SET UP
see page119
WIPER SET
UP
see page130

ÛÝÛÝ
While the multi-information display
is in the ACC SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display. Press the SEL/RESET button. The
screen changes as shown above. The
highlighted unit, mph or km/h, is
the current setting. To change the
setting, press the INFO ( / )
button until the unit you want is
highlighted, then press the SEL/
RESET button.
To change the unit of measurement
f rom mph to km/h, do this:
CONT INUED
Multi-Inf ormation Display
A dapt ive Cruise Cont rol Display
Speed Unit
Inst rument s and Cont rols
89

ÛÝÛ
Ý
While the multi-information display
is in the METER SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display. Press the SEL/RESET button. The
screen changes as shown above. The
highlighted number is the current
setting above or below the outside
temperature. Press the INFO ( /
) button repeatedly until the
number you want appears, then
press the SEL/RESET button to
enter your selection.
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions:
Multi-Inf ormation Display
A djust Outside T emp. Display
94

Û
Ý
ÛÝ Û
Ý
ÛÝ
CONT INUED
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button.
Multi-Inf ormation Display
K EYL ESS A CCESS Setup
Inst rument s and Cont rols
105
Press the or button.
Press the SEL/RESET button. seepage106
seepage108
seepage110

ÛÝÛÝ
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
The same exterior lights blink once
when you lock the doors by touching
the door lock sensor while carrying
the remote.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
Multi-Inf ormation Display
K eyless A ccess L ight Flash
108

ÛÝ
To exit KEYLESS ACCESS LIGHT
FLASH without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
keyless access light f lash setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109